METREL A 1445 User manual
Flex current clamps
A 1445
User Manual
Version 1.1.0; Code No. 20 752 635
2
Distributor:
Producer:
METREL d.d.
Ljubljanska 77
SI-1354 Horjul
Tel.: +386 1 75 58 200
Fax: +386 1 75 49 226
http://www.metrel.si
Mark on your equipment certifies that this equipment meets the requirements
of the EC (European Community) regulations concerning safety and
electromagnetic compatibility.
© 2016 Metrel
No part of this publication may be reproduced or utilized in any form or by any means
without permission in writing from METREL.
Flex current clamps A 1227
3
Table of contents
1Introducing the A1445 ..............................................................................................4
2Features ...................................................................................................................5
3Safety .......................................................................................................................6
4Symbols....................................................................................................................7
5Measuring current with A 1445.................................................................................8
6Cleaning ...................................................................................................................9
7Service....................................................................................................................10
8Technical specifications..........................................................................................11
Flex current clamps A 1445
4
1 Introducing the A1445
The A 1445 Flexible Current Clamps consist of the flexible sensor and an
electronic module on the connected wire. It has three current ranges 30A, 300A and
3000 A. The current range of the A 1445 is selected directly by the connected
instrument. The electronic module is powered from the connected instrument to. The
flexible sensor permits measurements on conductors where standard clamp-on current
transformers can not be used. It is particularly useful for installation in tight spaces, or
around breaker panels, cable bundles, wide or large bus bars and irregular shapes.
Unlike standard current transformers, this flexible CP does not use magnetic cores.
The transformation principle is based on an air core. It presents virtually no load to the
system under test, has a low phase shift and excellent frequency response.
Additionally, A 1445 cannot be damaged by overloads. The A 1445 Flexible
Current Clamps are insensitive to DC current and measure only the AC component of
the measured signal.
Flex current clamps A 1445
5
2 Features
Range setup from the instrument, no additional range setup needed
Power supply for electronic module is assured from the instrument
mV output
Waterproof sensor
Minimum angle shift to accomplish accurate power measurements
High accuracy
Total rejection of d.c. component
Friendly-use of the closing-opening system of the current sensor (even if wearing
gloves) due to its highly ergonomic design
It is possible to set the seal on the closing system of the current clamp.
Very light, flexible and fully adaptable to busbar trunking system and insulated
cables
Strengthened security, regardless the working environment industrial or services
Flex current clamps A 1445
6
3 Safety
Read the operating instructions before use and follow all safety instructions.
If the test equipment is used in a manner that is not specified in this user
manual, the protection provided by the equipment might be impaired!
Adhere to local and national safety codes. Individual protective equipment must
be used to prevent shock and arc blast injury where hazardous live conductors
are exposed.
Before each use, inspect the Current Clamps and its latching system for any
damage. Pay particular attention to the insulation surrounding the flexible
measuring head. Look for cracks or missing portions of the clamp housing or
output cable insulation. Also look for loose or weakened components.
Do not use a clamp that is cracked, damaged, or has a defective cable.
Never use the clamp on a circuit with voltages higher than 1000 V CAT III or
600V CAT IV.
De-energize the installation on which current will be measured or adopt safe
operating procedures during application and removal of the current clamp.
Use extreme caution when working around bare conductors or bus bars.
Do not use the Current Clamp to measure bare conductors carrying a voltage
from 30V up to 1000V unless you are wearing protective clothing suitable for
high-voltage work. Contact with the conductor could result in electric shock.
Always use appropriate equipment for personal protection.
Use caution when working with voltages above 60 V dc, 30 V ac rms or 42 V ac
peak. Such voltages pose a shock hazard.
Flex current clamps A 1445
7
4 Symbols
Symbol
Description
Important information. Refer to the manual.
Risk of Electric Shock.
Product is protected by Double/Reinforced insulation
Do not apply around or remove from HAZARDUS LIVE conductors.
Do not dispose of this product as unsorted municipal waste. Contact
Metrel or a qualified recycler for disposal.
Complies with the relevant European standards.
Flex current clamps A 1445
8
5 Measuring current with A 1445
I
1
2
Picture 5.1: Wrap the measured cable with the measuring clamp
To use the A 1445 Flexible Current Clamps, follow these instructions:
1. Connect the D01 3 Pin connector of the A1445 Flexible Current Clamps to the
desired input on the measuring instrument (power meter,..) .
2. Select the corresponding sensitivity (.. mV/A) on your instrument.
3. Wrap the flexible measuring head around the conductor to be tested, close coupling
(See Picture 5.1 ).
4. It is very important that the conductor is as the center and perpendicular to the
measuring head. (if it is no possible additional error of 2% of full scale can occur).
5. Do not measure close to other current-carrying conductors if possible. (An external
field of 40 A/m can cause an additional measurement error of 1% of full scale).
6. Make sure that the arrow marked on the clamp coupling points toward the correct
orientation for correct phase. (See Picture 5.1 )
7. Keep the clamp coupling more than 2.5 cm (1 inch) away from the conductor to be
tested and other nearby conductors.
8. Observe the current value and waveform on the instrument’s display. If desired,
select the lower range on the measurement instrument.
Flex current clamps A 1227
9
6 Cleaning
Use soft patch, slightly moistened with soap water or alcohol, to clean the surface
of the A 1445 and leave it to dry totally, before using it.
Do not use liquids based on petrol or hydrocarbons!
Do not spill cleaning liquid over the A 1445!
Flex current clamps A 1445
10
7 Service
For repairs under or out of warranty time please contact your Metrel distributor for
further information.
Name and address of manufacturer:
METREL d.d.
Ljubljanska cesta 77
SI-1354 Horjul
Tel.: +386 1 75 58 200, fax.: +386 1 75 49 226, +386 1 75 49 206
http://www.metrel.si
E-mail: metrel@metrel.si
Table of contents
Other METREL Measuring Instrument manuals
METREL
METREL power master MI 2892 User manual
METREL
METREL PowerQ4MI 2592 User manual
METREL
METREL EurotestXC User manual
METREL
METREL MD 9273 User manual
METREL
METREL Instaltest 61557 MI 2087 User manual
METREL
METREL MI 3102 Manual
METREL
METREL EurotestXC MI 3152 User manual
METREL
METREL A 1446 User manual
METREL
METREL MD 9225 User manual
METREL
METREL MD 126 User manual
METREL
METREL DeltaGT MI 3309 User manual
METREL
METREL MicroOhm 2A MI 3242 User manual
METREL
METREL EurotestDL User manual
METREL
METREL EurotestAT MI 3101 User manual
METREL
METREL VoltScanner MI 2130 User manual
METREL
METREL MD 9250 User manual
METREL
METREL MI 3295 User manual
METREL
METREL A 1378 User manual
METREL
METREL power master MI 2892 User manual
METREL
METREL GammaGT MI 3311 User manual
