Messoa NCR870 User manual

This manual suits for next models

4

Table of contents

Languages:

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

ZEIM-4000880G 870 A1

IR Bullet Network Camera

Quick Start Guide

Guia de inicio rápido

Guida rapida

Guide de démarrage rapide

Краткое руководство

クイックスタートガイド

快速安裝指南

快速安装指南

Quick Start Guide 1

English

Safety Instructions

Make sure the supplied voltage meets the power consumption requirements

of the camera before powering the camera on. Incorrect voltage may cause

damage to the camera.

The camera should be protected from water and moisture, excessive heat,

direct sunlight and cold.

This installation should be made by a qualied service person and should

conform to all local codes.

Unplug the camera during lightning storms or when unused for long periods

of time.

2 Quick Start Guide

Compliance

This equipment complies with the requirements as listed below:

FCC Part 15 Class B

CE: 2004/108/EC-Electromagnetic Compatibility (EMC) directive of EN55022

and EN55024.

WEEE

Waste Electrical and Electronic Equipment

Correct disposal of this product (applicable in the European Union

and other European countries with separate collection systems). This

product should be disposed of, at the end of its useful life, as per

applicable local lows, regulations and procedures.

Quick Start Guide 3

English

1. Introduction

1.1 Package Contents

Bullet Network Camera x1

CD-ROM (User manual and IP Finder utility) x1

Quick Start Guide x1

Guide Pattern x1

RJ-45 Female / Female Coupler x1

Pack-in Bracket x1

Accessories x3

• Flat Head Screw (Tapping Type) (#1) x3

• Plastic Anchor (#2) x3

1.2 Dimensions

81.5mm (3.21”)

ø91mm (3.58”)

ø70mm (2.76”)

ø162mm (6.4”)

ø111mm (4.4”)

Power

RJ-45 / PoE

BNC

4 Quick Start Guide

2. Installation

2.1 Mounting the Camera

1. Post the supplied “Guide Pattern” sticker on the mounting surface.

2. Aiming the circles on the sticker, drill three screw holes and one cable entry

hole in the ceiling/wall.

3. Optionally insert the provided anchors into the screw holes.

• For cement surfaces, insert the anchors into the holes.

• For softer surfaces, there is no need to use the anchors.

4. Position the bracket to the mounting holes. Use the supplied tapping screws

to secure the bracket to the surface.

To adjust the view angle, loosen the

knob to rotate the bracket.

5. To adjust the view angle, loosen the knob to rotate the bracket. After

adjustment is done, make sure to tighten the knob.

2.2 Making the Connection

1. Power: Connect to DC 12V/AC 24V (non-heater model) or DC 24V/AC 24V

(heater model) power supply. If using the DC power supply, make sure the

power connector is wired to correct polarities (Red+/Black–). If you are to use

power via the PoE connection, this connector is not used.

Quick Start Guide 5

English

2. RJ-45 (PoE): Connect to the LAN port of a standard 10BaseT/100BaseTX

device, e.g., hub, switch or router. If you are going to use PoE function,

connect to a PoE-capable network device. Power will be supplied through the

Ethernet cable.

3. BNC: Connect to composite video in connector of a monitor.

2.3 Initial Conguration

Before connecting the camera to your network infrastructure, it’s suggested that

you connect the camera to a computer rst to perform initial congurations.

1. Congure the computer’s IP address to one other than the camera’s default

IP address, such as:

• IP Address: 192.168.1.100

• Subnet Mask: 255.255.255.0

2. Usning an Ethernet cable, connect the camera to the computer.

The LAN port of the camera supports auto MDI/MDIX so there is no need to

use a cross-over cable.

3. On the PC, launch a web browser and enter the IP address of the camera in

the URL eld:

http://192.168.1.30

4. When prompted for login, enter the default user name: admin and

password: 1234 to login. Note that the user name and password are case-

sensitive.

5. Congure the settings to meet your requirements. For more information,

refer to the User Manual on the provided CD.

6 Quick Start Guide

2.4 Connecting to Your Network

Connecting to a LAN

If you have multiple cameras installed on your network, you can use the provided

IP Finder utility to manage the cameras. For more information, refer to the User

Manual on the provided CD-ROM.

Router/Switch/Hub

Connecting to the Internet

Router

xDSL/Cable

Modem

To enable remote access to the cameras, you must congure your router/rewall

to open port numbers. For more information, refer to the User Manual on the

provided CD-ROM.

ZEIM-4000880G 870 A1

Cámara de Red Tipo IR Bala

Guia de inicio rápido