Messoa NCB355 User manual

3MP/5MP Fixed Network Camera

Quick Guide

201402 355.358 A1

Quick Start Guide

Table of Content

1Product Overview 3

1.1 Physical Characteristics 3

2Installation 5

2.1 Package Content 5

2.2 Installation 5

2.2.1 Connecting the Wires 5

2.2.2 Mounting the camera 6

3Connection 7

3.1 Network Topology 7

3.2 Accessing the Camera for the First Time 7

3.3 IP Finder 8

Quick Start Guide

WARNING

This unit operates at DC 12V/ AC 24V/ PoE.

Installation and service should be performed only by qualified and experienced technicians and comply

with all local codes and rules to maintain your warranty.

To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.

Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and

wipe with a dry soft cloth.

Do not apply benzene or thinner to the camera, which may cause the surface of unit to be melted or lens

fogged.

Avoid aligning the lens to very bright objects (example, light fixtures) for long periods of time.

Avoid operating or storing the unit in the following locations:

Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -10°C to +50°C )

Close to sources of powerful radio or TV transmitters

Close to fluorescent lamps or objects with reflections

Under unstable or flickering light sources

Compliance

This equipment complies with the requirements as listed below:

FCC Part 15 Class B

CE: EMC directive and General Product Safety Directive GPSD conforming to requirements of standards

EN55022 for emission, EN 55024 for immunity, EN 300 and EN 328 for WIFI.

WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product

(applicable in the European Union and other European countries with separate collection

systems). This product should be disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

Quick Start Guide

1Product Overview

1.1 Physical Characteristics

Figure 1 - 1: Pictorial Index

Quick Start Guide

Table 1 - 1: Pictorial Index Definition

Index #

Name

Description

CS Mount

To connect a lens with the unit (lens sold separately)

Lock Screw

To lock back focus Adjustment

Back Focus Adjustment

To adjust focus

Mounting Block

The block contains 2 standard female threaded receptacles

itself and is able to connect the unit with a bracket via

standard thumbscrew.

Auto (DC) Iris Control

Port

When mounting a lens, connect the DC iris control line here

(lens with iris control sold separately)

SD Card Slot

To insert a SDHC/SDXC card into this slot for storage

BNC Video Outlet

To output video signal

RJ-45 Ethernet

Connector/ PoE

To insert the RJ-45 cable for network connection as well as

PoE (Power over Ethernet) capability

Default Button

To restore all settings of the unit to the factory defaults by

pressing for 5 seconds

Reset Button

To reboot the unit

Power Indicator

To indicate power status with red light

I/O Connector

To connect Input/ Output devices via the 8-pin removable

terminal block (supplied)

Power Terminal

DC12V/AC24V, red port: power +/white port: power –/ black

port: GND. Make sure to connect the power connector to

correct ports (+ and –) when the power supply is DC12V.

Ethernet Link LED

Solid green light stands for a live connection is established

Ethernet Activity LED

Amber flashing indicates data is being transmitted / received

by the unit

Table 1 - 2: I/O Connector Definition

A/I

Audio in

GND

A/O

Audio out

GND

Alarm out

COM

Alarm in

GND

Note

Power supply terminal/adaptor for IO connectors and field wiring should comply with the Class

2 Circuit standard for ensuring safe from electrical fires and providing acceptable protection

against electrical shock.

Quick Start Guide

2Installation

2.1 Package Content

Check everything in the packing box matches to the order form and the packing slip. In addition to this manual,

items below are included in the packing box.

One unit of network Box Camera

One 8-pin terminal block for alarm input/output

One CD containing the IP Finder, user manual, and quick installation guide

One printed quick installation guide

Please contact your dealer if any item missing.

2.2 Installation

When first unboxing, please check whether if there is any visible damage to appearance of the unit and its

accessories. The protective materials used for the packaging should be able to protect the unit from most of

accidents during transportation.

Please remove the protective film of the unit when every item is checked in accordance with the list in “2.1

Package Content”

2.2.1 Connecting the Wires

Connect the power cable to the power plugs with one of the following options.

DC 12V: Connect 12V (－) to terminal =DC 12V－, and Connect 12V (＋) to terminal =DC 12V＋

If using DC supply, make sure the polarity is correct. Incorrect connection may cause malfunction

and/or damage to the unit.

AC 24V: Connect 24V (～) cables to terminals ～AC 24V

PoE: Connect the RJ-45 jack to a PoE compatible network device that supplied power with

networking capability through the Ethernet cable.

Insert audio cable and alarm cable to the corresponding connectors of the unit if required.

Quick Start Guide

2.2.2 Mounting the camera

Please insert the screws into the mounting block and either top or bottom holes of the unit. Securely

fasten the screws to ensure the mounting block is connected with the unit tightly. Select a bracket (sold

separately) which has a standard thumbscrew matching the threaded receptacles of the mounting block

and tighten them. Depending on different applications, mount your selected bracket onto wall/celling to

complete mounting procedure.

Connect the Safety Wire (Fall Prevention Wire, not supplied) with one end to the wall/ceiling and the

other end to the safety-cord screw of the unit.

Figure 2 - 1: Mounting the Camera

Note

To prevent the unit from falling off, ensure that it is mounted to a firm place (ceiling slab or

channel) using a safety wire strong enough to withstand the total weight of the unit. (Pay also

attention to the finishing at the end of the wire.) By cabling so, it is possible to prevent the unit

from accidental falling suddenly at any time.

Safety wire (fall prevention wire, not supplied)

Safety-cord screw of the unit

Quick Start Guide

3Connection

3.1 Network Topology

The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images and audio in real

time via either Internet or Intranet. Please refer to the skeleton drawings shown below for understanding.

Figure 2 - 2: Network Topology TypeⅠ

Figure 2 - 3: Network Topology TypeⅡ

3.2 Accessing the Camera for the First Time

The camera comes with a web-based setup utility, allowing you to view the video of the camera and configure

the camera for optimal use in your environment. Take the following steps to connect your PC to the camera.

Step 1: Make the connection

For initial setup purposes, connect one end of an Ethernet cable to the RJ-45 connector of the camera and

the other end to the LAN port on your PC.

Step 2: Configure your PC’s IP address

The camera uses a default IP address of 192.168.1.30 and subnet mask of 255.255.255.0. To have your PC

on the same network with the camera, configure your PC’s IP settings as below:

IP address: 192.168.1.X, where X is a number between 2 to 254, excluding 30.

Subnet mask: 255.255.255.0.

Quick Start Guide

Step 3: Link Verification between PC and Camera

1. Launch the Command Prompt by clicking the Start menu, Programs, Accessories and then Command

Prompt.

2. At the prompt window, type ping x.x.x.x, where x.x.x.x is the IP address of the camera (the default is

192.168.1.30). If the message of “Reply from…” responds, it means the connection is established.

Step 4: Accessing the Camera from IE Browser

Open the IE browser and enter the IP address of the camera in the URL field. The default is 192.168.1.30.

When prompted for login, enter the user name and the password (The defaults: admin, 1234). Note that the

user name and password are case-sensitive.

3.3 IP Finder

IP Finder is a utility program that helps users to locate the unit in local area network that computer is

connected to. Please note that IP Finder works only in Microsoft Windows XP, Microsoft Windows Vista, and

Microsoft Windows 7.

To install the software, simple locate and double-click the IP Finder setup file on the provided CD. Then follow

the on-screen prompts to proceed.

After you launch IP Finder, the window would list information of units in operation at present, and user can

press FIND CAMERA to find more units. Locate and double-click one of the cameras in the list you want to

configure the network settings. Click Save to enable the settings and click Exit to exit the utility.

Figure 2 - 4: IP Camera Finder

3MP/5MP 固定式网络摄像机

快速安装指南

201402 355.358 A1

This manual suits for next models

Table of contents

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications