Lubemate L-OCGAE User manual

2 Lubemate |

macnaught.com

INSTRUCTION MANUAL

30locg-rev-1-2018

Lubemate®is a practical, cost-effective range of

equipment brought to you by the trusted team at Macnaught.

All Lubemate products are specially selected by our

experienced technical team at Macnaught®, ensuring they meet our

strict quality standards.

Macnaught Pty Ltd

41-49 Henderson St, Turrella NSW 2205. Australia

Ph: 1800 185 102 Fax: +61 2 9597 7773

Email: info@macnaught.com Website: macnaught.com

OIL CONTROL GUN LOCGAE, LOCGME

Thank you for purchasing a Lubemate oil control nozzle. Your oil control nozzle has

been designed to reliably dispense engine oil, gear oil, automatic transmission fluid

and premix automotive coolants. This manual assists in operating and maintaining

your new oil control nozzle. Please take a few minutes to read through this manual

before installing and operating your new oil control nozzle.

For Macnaught warranty, terms and conditions see macnaught.com/warranty ©Macnaught Pty Ltd, 2017

1/2" BSP (F) inlet swivel

Flexible extension with automatic nozzle

Flow rate up to 30LPM

TECHNICAL SPECIFICATIONS

Suitable for oils up to SAE 140, engine

oils, gear oils, ATF and hydraulic oils

Max pressure up to 6,900kPa (1,000psi)

1/2" BSP (F) inlet swivel

Flexible extension with manual nozzle

Flow rate up to 30LPM

TECHNICAL SPECIFICATIONS

Suitable for oils up to SAE 140, engine

oils, gear oils, ATF and hydraulic oils

Max pressure up to 6,900kPa (1,000psi)

Flexible extension with auto nozzle

easy access in tight spaces and auto nozzle avoids

cross-contamination and fluid wastage.

Flexible extension with auto nozzle

easy access in tight spaces and auto nozzle avoids

cross-contamination and fluid wastage.

Compact and light weight design

aluminium die cast handle.

Compact and light weight design

aluminium die cast handle.

Continuous flow switch

trigger can be locked for unattended dispensing.

Continuous flow switch

trigger can be locked for unattended dispensing.

Built-in strainer

stops foreign material from entering the gun.

L-OCGAE

L-OCGME

Built-in strainer

stops foreign material from entering the gun.

NOTE: This product should be disposed of according to all applicable

local and national government environment regulations and guidelines!

Wearing parts:

Part No. Description Q'ty

1* O-ring 1

9* O-ring 1

13* Battery 1

19* Waterproof protector 2

20* Seal washer 4

Part No. Description Q'ty

1* O-ring 1

2 Meter Holder 1

3 Meter Cover 1

4 Rubber Protector 1

5 Main Circuit Board 1

6 Front Label 1

7 Screw 4

8 Screw 4

9* O-ring 1

10 Seat 1

11 Battery cover 1

12 Spring

13* Battery 1

14 Screw 2

15 Shaft 2

16 Oval Gear 2

17 Magnetic Rod 2

18 Bolt 8

19* Waterproof protector 2

20* Seal washer 4

21 Washer 4

No Spare Parts Available

MAC0619_Lubemate_InstructionManual_L-OCGAE-L-OCGME_D2.indd 1-2 7/8/18 4:46 pm

macnaught.com

3 Lubemate | Oil Control Gun

INSTRUCTION MANUAL

GENERAL SAFETY REGULATIONS

1. Keep the work area clean and dry. Damp or

wet work areas can result in injury.

2. Keep children away from work area. Do not

allow children to handle this product.

3. Use the right tool for the job. Do not attempt

to force small equipment to do the work of larger

industrial equipment. There are certain applications

for which this equipment was designed. It will

do the job better and more safely at the capacity

for which it was intended. Do not modify this

equipment, and do not use this equipment for

a purpose for which it Was not intended.

4. Check for damaged parts. Before using this

product, carefully check that it will operate

properly and perform its intended function.

Check for damaged parts and any other conditions

that may affect the operation of this product.

Replace damaged or worn parts immediately.

5. Do not overreach. Keep proper footing and

balance at all times to prevent tripping, falling,

back injury, etc.

6. DO NOT use the equipment when tired or under

the influence of drugs, alcohol, or medication.

A moment of inattention while operating this

equipment may result in serious personal injury.

SAFETY PRECAUTIONS

WARNING

Read carefully and understand all INSTRUCTIONS

before operating. Failure to follow the safety

rules and other basic safety precautions may

result in serious personal injury. Save these

instructions in a safe place and on hand so that

they can be read when required. Keep these

instructions to assist in future servicing.

WARNING!

The warnings, cautions, and instructions

discussed in this instruction manual cannot cover

all possible conditions or situations that could

occur. It must be understood by the operator

that common sense and caution are factors that

cannot be built into this product, but must be

supplied by the operator.

INSTALLATION

1. This oil control valve has a 1/2" BSP threaded oil inlet, use Teflon tape or an equivalent oil resistant

thread sealant on all threaded connections.

TROUBLESHOOTING GUIDE

Always turn off and relieve line pressure before carrying out any maintenance or repairs.

Ensure that all equipment in the system are operating properly.

AREA 4:

FOR BATTERY CAPACITY

AREA 2: FOR MEASUREMENT UNITS

Value

ER14250 3.6V

1-35L/min

0.5-100bar

Data

Flow rate

Operating Pressure Range

60°C

±0.5%

Accuracy

Battery

Max operation temperature

Fig. 2

1. Air supply

2. Shut off air valve

3. Oil Pump

4. Shut off oil valve

5. Hose reel

6. Oil control valve

Display and button usage

Notes: It will flashing when

battery voltage less than 3.3V;

AREA 1: FOR LAST DISPENSE CYCLE

AREA 3:

FOR ACCUMULATED TOTAL

Menu:

MOVING THE NUMBERS FOR

ADJUSTING THE CALIBRATION

AND CHOOSING THE UNITS

Reset:

CHOOSING THE UNITS AND

SETTING CORRECTION FACTOR

AREA 4:

FOR BATTERY CAPACITY

AREA 2: FOR MEASUREMENT UNITS

Value

ER14250 3.6V

1-35L/min

0.5-100bar

Data

Flow rate

Operating Pressure Range

60°C

±0.5%

Accuracy

Battery

Max operation temperature

Fig. 2

1. Air supply

2. Shut off air valve

3. Oil Pump

4. Shut off oil valve

5. Hose reel

6. Oil control valve

Display and button usage

Notes: It will flashing when

battery voltage less than 3.3V;

AREA 1: FOR LAST DISPENSE CYCLE

AREA 3:

FOR ACCUMULATED TOTAL

Menu:

MOVING THE NUMBERS FOR

ADJUSTING THE CALIBRATION

AND CHOOSING THE UNITS

Reset:

CHOOSING THE UNITS AND

SETTING CORRECTION FACTOR

Problem Cause Solution

Slow or no

fluid flow

Filter is clogged, or pump pressure is

low, or shut-off valve is not fully open,

or foreign materialis jammed in the

metering element.

1. Relief the pressure.

2. Loose swivel fitting, clean or

replace the filter.

3. If the problem remains,

contact your distributor for

repair or replacement.

Oil leaks

from swivel

Swivel is loose

O-ring is worn or damaged

Torque the swivel.

If the problem remains, contact your

distributor for repair or replacement.

Replace the o-ring.

If the problem remains, contact your

distributor for repair or replacement.

Oil drips

from nozzle Nozzle is damaged or obstructed

Inspect the nozzle for damage or

obstructions, and replace if damaged

If the problem remains, contact your

distributor for repair or replacement.

Valve leaks O-rings or valve seat are worn or

damaged

Replace the o-rings and/or the

valve seat. If the problem remains,

contact your distributor for repair

or replacement.

No spare parts available.

MAC0619_Lubemate_InstructionManual_L-OCGAE-L-OCGME_D2.indd 3-4 7/8/18 4:46 pm

Lubemate®is a practical, cost-effective range of

equipment brought to you by the trusted team at Macnaught.

All Lubemate products are specially selected by our

experienced technical team at Macnaught®, ensuring they meet our

strict quality standards.

Macnaught Pty Ltd

41-49 Henderson St, Turrella NSW 2205. Australia

Ph: 1800 185 102 Fax: +61 2 9597 7773

Email: info@macnaught.com Website: macnaught.com

TECHNICAL SPECIFICATIONS

MAC0619_Lubemate_InstructionManual_L-DHFOG-L-HFOG_D1.indd 1 7/8/18 4:33 pm

This manual suits for next models

Other lubemate Measuring Instrument manuals

lubemate

lubemate L-DPOCG User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

lubemate L-OCGAE User manual

Popular Measuring Instrument manuals by other brands