Kichler Lighting Verdi User manual

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

56" Verdi LED

2 | KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES..................................................................4

TOOLS REQUIRED............................................................5

PACKAGE CONTENTS ....................................................5

MOUNTING OPTIONS.................................................... 6

HANGING THE FAN..........................................................7

INSTALLATION OF SAFETY SUPPORT................... 9

ELECTRICAL CONNECTIONS .................................. 10

FINISHING THE MOTOR INSTALLATION.............. 11

ATTACHING THE FAN BLADES.................................12

INSTALLING THE SWITCH HOUSING.....................13

INSTALLING THE LIGHT KIT AND GLASS ............14

OPERATING INSTRUCTIONS.....................................17

TROUBLESHOOTING… ............................................... 18

FCC INFORMATION… ....................................................19

56" Verdi LED | 3

4 | KICHLER.COM

1. CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or

main fusebox before starting and during the installation.

2. WARNING: This fixture is intended for installation in

accordance with the National Electrical Code (NEC) and

all local code specifications. If you are not familiar with

code requirements, installation by a certified electrician

is recommended.

3. WARNING: To reduce the risk of fire or electric shock,

use only the control provided with the fan.

4. WARNING: To reduce the risk of fire, electric shock, or

Personal Injury, mount directly to a structural framing

member or to an outlet box marked “Acceptable for

Fan Support of 15.9kg (35 lbs) or less”. For outlet box

mounting, use mounting screws provided with the outlet

box.

5. WARNING: Chemical Burn Hazard. Keep batteries

away from children. This remote contains a lithium

button cell battery. If a new or used lithium button/

coin cell battery is swallowed or enters the body, it can

cause severe internal burns and can lead to death in as

little as 2 hours. Always completely secure the battery

compartment. If the battery compartment does not

close securely, stop using the product, remove the

batteries, and keep it away from children. If you think

batteries might have been swallowed or placed inside

any part of the body, seek immediate medical attention.

Dispose of cells properly and keep away from children.

Even used cells may cause injury.

6. To operate the reverse function on this fan, press the

“Reverse” button while fan is running.

7. Avoid placing objects in the path of the blades.

8. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

9. Make sure the installation site you choose allows a minimum

clearance of 7 feet from the blades to the floor and at least 30

inches from the ends of the blades to any obstruction.

10. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections, spliced conductors

should be turned upward and pushed carefully up into outlet

box. The wires should be spread apart with the ground wire

and white (common) wire to one side with the black (load) wire

to the other side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that

are not packed with the fan must be ETL Listed and marked

suitable for use with the model fan you are installing. Switches

must be ETL General Use Switches. Refer to the Instructions

packaged with the light kits and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

• Phillips Screwdriver

• Blade Screwdriver

• 11 mm Wrench

• Step Ladder

• Wire Cutters

Unpack your fan and check the contents. You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Fan Blade (5)

H. Switch Housing

I. Light Kit

J. Glass

K. Remote Control Kit:

Remote Control (1)

Receiver (1)

Batteries (2)

Wire Connectors (6)

L. Package Hardware

1) Mounting Hardware:

Wire Connector (3)

2) Blade Attachment Hardware:

Screws (15) , Washers (15)

3) Safety Cable Hardware:

Wood Screw (1), Spring Washer (1),

Flat Washer (1)

4) Light Kit Hardware:

Screw (3)

CR2032 3V

56" Verdi LED | 5

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect

the power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the moving

weight of the fan (at least 50 lbs). Do not use plastic outlet

boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist

Hanger” for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 30° ANGLE

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is

necessary for your safety and also the proper programming of the control

system.

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching the fan to outlet box (not included), ensure the outlet

box is securely fastened to at least two points to a structural ceiling member

(a loose box will cause the fan to wobble). Pass the 120 volt supply wires from

the ceiling outlet box through the center of the ceiling mounting bracket. Install

mounting bracket to outlet box in ceiling using the screws and washers included

with the outlet box. (Fig. 5)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain

for later use. Remove the hanger ball from the downrod assembly by loosening

set screws, removing the cross pin, and twisting ball o the rod.( Fig. 6)

NOTE: Make sure to keep loosened hardware separate to avoid confusion

during installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 7)

Fig. 5

Fig. 6

Fig. 7

Hairpin

Outlet Box

Ceiling Mounting Bracket

Flat Washer

Screw

Hanger Ball

Set Screw

Cross Pin

Clevis Pin

Motor Body

Set Screw

56" Verdi LED | 7

8 | KICHLER.COM

HANGING THE FAN (continued)

Step 3. Carefully feed fan wires and safety cable up through the downrod.

Thread the downrod onto the motor coupling until the clevis pin holes are

aligned. Next, replace the clevis pin and hairpin, then tighten both set screws.

(Fig. 8)

Step 4. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod . Make sure

the cross pin is in the correct position and the set screw is tight and the wires

are not twisted. (Fig. 9)

Step 5. Now lift the motor body into position and place the hanger ball into

the mounting bracket. Rotate until the "Check Tab" has dropped into the

"Registration Slot " and seats ﬁrmly. (Fig. 10) The entire motor body should

not rotate if this is done correctly.

WARNING: Failure to properly seat the "Check Tab" can damage the ceiling

fan during operation.

Fig. 8

Fig. 9

Fig. 10

Hairpin

Set Screw

Canopy

Canopy Hole Cover

Coupling Cover

Downrod

Mounting Bracket

Registration Slot

Check Tab

Hanger Ball

Set Screw

Cross Pin

Clevis Pin

Motor Body

Clevis Pin

Hairpin

Set Screw

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from falling,

please install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the

outlet box. Leave 3mm (1/8") of space between the support brace and the washer.

(Fig. 11)

Step 2.Insert the safety cable through the mounting bracket and one of the holes

in the outlet box into the ceiling. Adjust the length of the safety cable to reach the

screw and washers by pulling the extra cable through the cable clamp until the

overall length is correct, put the end of the cable back through the cable clamp,

forming a loop at the end of the cable. Tighten the cable clamp securely. Now, put

the loop in the end of the safety cable over the wood screw and under the washer.

Tighten the wood screw securely. (Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations

only. It’s a good idea to make the attachment with any installation.

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 12

Fig. 11

56" Verdi LED | 9

10 | KICHLER.COM

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power

at the main circuit panel before wiring.

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make

sure there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors than referenced in this manual,

stop immediately. A professional electrician is recommended to determine proper

wiring.

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of

ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connections:

Connect the BLACK wire from the fan to BLACK wire marked "TO MOTOR L" from

the receiver. Connect the WHITE wire from the fan to the WHITE wire marked "TO

MOTOR N" from the receiver. Connect the BLUE wire from the fan to the BLUE wire

marked "FOR LIGHT " from the receiver. Secure all the wire connections with the

plastic wire connectors provided. (Fig. 14)

Step 3. Remote Receiver to Outlet Box Electrical Connections:

Connect the BLACK (hot) wire from the ceiling to the BLACK wire marked “AC IN L”

from the receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITE

wire marked “ AC IN N” from the receiver. Secure all the wire connections with the

plastic wire connectors provided. (Fig. 14)

Mounting Bracket

Receiver

Outlet Box

Black

Black ("AC IN L")

Receiver

Black ("TO MOTOR L")

Black (motor)

Blue (FOR LIGHT)

Blue (for light)

White

Green or bare copper

(ground)

White ("AC IN N")

White ("TO MOTOR N")

Ground wire

White (Neutral)

Fig. 13

Fig. 14

This manual suits for next models

Table of contents

Languages:

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting 35152 User manual

Kichler Lighting

Kichler Lighting VASSAR User manual

Kichler Lighting

Kichler Lighting Cameron User manual

Kichler Lighting

Kichler Lighting Renew Premier User manual

Kichler Lighting

Kichler Lighting IMARI 300365SBK User manual

Kichler Lighting

Kichler Lighting Renew Select User manual

Kichler Lighting

Kichler Lighting Canfield User manual

Kichler Lighting

Kichler Lighting 310155 User manual

Kichler Lighting

Kichler Lighting Starkk User manual

Kichler Lighting

Kichler Lighting 35155 User manual

Kichler Lighting

Kichler Lighting Lija User manual

Kichler Lighting

Kichler Lighting Eris User manual

Kichler Lighting

Kichler Lighting Canfield 300117WH User manual

Kichler Lighting

Kichler Lighting Selectlight fixture User manual

Kichler Lighting

Kichler Lighting 52" RENEW ENERGY STAR User manual

Kichler Lighting

Kichler Lighting Maeve LED 52 User manual

Kichler Lighting

Kichler Lighting 310125 User manual

Kichler Lighting

Kichler Lighting Chicago User manual

Kichler Lighting

Kichler Lighting Compass 300322 User manual

Kichler Lighting

Kichler Lighting Olympia User manual

Kichler Lighting

Kichler Lighting True User manual

Kichler Lighting

Kichler Lighting Incus User manual

Kichler Lighting

Kichler Lighting KAPONO User manual

Kichler Lighting

Kichler Lighting Ried 300356 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual