Kichler Lighting 310155 User manual

Kichler® Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

RanaTM

310155

Instruction Manual

UL Model # 60-RECI

1. SAFETY RULES

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualied licensed electrician.

3. WARNING: Suitable for use with solid-state

speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes

commonly used for the support of lighting

xtures are not acceptable for fan support and

may need to be replaced, consult a qualied

electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of reliably

supporting a minimum of 50 pounds. Use only

CUL Listed outlet boxes marked “FOR FAN

SUPPORT”.

6. The fan must be mounted with a minimum of

7 feet clearance from the trailing edge of the

blades to the oor.

7. Do not operate reversing switch while fan

blades are in motion. Fan must be turned off

and blades stopped before reversing blade

direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan

and other items, be cautious when working

around or cleaning the fan.

10. Do not use water or detergents when cleaning

the fan or fan blades. A dry dust cloth or lightly

dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced

conductors should be turned upward and

pushed carefully up into outlet box. The wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are reference only. Light

Kits that are not packed with the fan must be

CUL Listed and marked suitable for use with

the model fan you are installing. Switches must

be CUL General Use Switches. Refer to the

Instructions packaged with the light kits and

switches for proper assembly.

13. Suitable for use in wet locations when installed

in a GFCI protected branch circuit.

14. Use only with light kits marked “Suitable for

use in wet locations”.

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL INJURY,

MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT”

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

WARNING

Charges or modications to this unit not

expressly approved by the party responsible

for compliance could void the user’s authority

to operate the equipment.

FCC: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

60” Rana™

2. TOOLS AND MATERIALS REQUIRED

• Phillips screw driver

• Blade screw driver

• 11mm wrench

• Step ladder

• Wire cutters

3. PACKAGE CONTENTS

Unpack your fan and check the contents.

You should have the following items:

a. Fan blade/blade arm assemblies (3)

b. Ceiling mounting bracket, Canopy

and Canopy bottom cover

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Light kit pan

g. Light kit tter assembly

h. Glass shade

i. Extra non-light cap (for fan without

light kit use)

j. Receiver

k. Wall transmitter

l. Parts bag contents:

1) Mounting hardware:

Star washers (2), wire nuts (3),

machine screws (2), washers (2),

wood screws (2)

2) Blade attachment hardware

screws (7)

3) Safety cable hardware:

wood screw, lock washer, at

washer

4. MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building structure.

Use appropriate fasteners and building materials. The

outlet box and its support must be able to fully support

the moving weight of the fan (at least 50 lbs). Do not

use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different ways to

mount the outlet box.

NOTE: If you are installing the ceiling fan on a sloped

(vaulted) ceiling, you may need a longer downrod

to maintain proper clearance between the tip of the

blade and the ceiling. A minimum clearance of 12” is

suggested for optimal operation.

NOTE: Depending on the location you have selected

for installation, you may need to purchase and install

a “Joist Hanger” for the support of the outlet box.

Make sure the joist hanger you purchase has been

designed for use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

ANGLED CEILING

MAXIMUM 30°ANGLE

Fig. 4

Fig. 3

Fig. 2

Fig. 1

60” Rana™

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

UL Listed

outlet box

120V Wires

Washers

Canopy

Canopy cover

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counterclockwise. (Fig.5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing (and save) one of

the two screws. Loosen the remaining screw by

a half turn. (Fig.5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove and discard the three screws

securing the plastic stabilizer on the bottom of

motor housing. Remove and discard the plastic

stabilizer. (Fig. 7)

Step 6. Remove the hanger ball from the

downrod assembly by loosening the setscrew,

removing the cross pin and turning the ball off

the downrod. (Fig.8)

Fig. 7

Fig. 6

Fig. 5

Plastic Stabilizer

Screws

Cross pin

Hanger ball

Set screw

Downrod

Fig. 8

Registration slot

Check tab

Supply wires

& Safety cable

Hitch

Set screw

Downrod

Set screw

Coupling

Retaining

clip

Hanger ball

Set screw

Downrod

Coupling

Canopy

Canopy cover

Coupling

cover

Cross pin

Supply wires

& Safety cable

Step 7. Loosen the two setscrews and remove the

hitch pin and retaining clip from the coupling on top

of the motor assembly. (Fig. 9)

Step 8. Carefully route the electrical supply

wires and safety cable exiting the top of the fan

motor assembly through the downrod. Thread the

downrod into the coupling until the hitch pin holes

are aligned. (Fig. 9)

Next, replace the hitch pin and retaining clip.

Tighten both setscrews. (Fig. 9)

Step 9. Slip the coupling cover, canopy cover and

canopy onto the downrod. (Fig. 10)

Thread the hanger ball onto the downrod, insert the

cross pin through the downrod and tighten. Now

tighten the set screw. (Fig. 10)

Step 10. Lift the motor assembly into position and

place the hanger ball into the ceiling mounting

bracket.

Rotate the entire assembly until the “Check Tab”

has dropped into the “Registration Slot” and seats

rmly. (Fig. 11)

The entire motor assembly should not rotate (left or

right) when seated properly.

WARNING: Failure to reattach the cross pin and

seat the “Check Tab” can cause the fan to fall from

the ceiling during operation. Take special care to

make sure this pin is reattached.

Fig. 10

Fig. 9

Fig. 11

60” Rana™

Code switch

MED

LOW

FAN OFF

ON ECE

1234

ON ECE

1234

6. INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the

ceiling fan from falling, please install it as follows.

Step 1. Attach the provided wood screw and washers

to the ceiling joist next to the mounting bracket but do

not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to reach

the screw and washers by pulling the extra cable

through the cable clamp until the overall length is

correct, put the end of the cable back through the

cable clamp, forming a loop at the end of the cable.

Tighten the cable clamp securely. Now, put the loop

in the end of the safety cable over the wood screw

securely.

NOTE: Although the safety support cable is required

for Canadian installations only. It’s a good idea to

make the attachment with any installation.

7. ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be

sure you have turned off the power at the main circuit

panel.

NOTE: The frequencies on your receiver and wall

transmitter have been preset at the factory. Before

installing the receiver, make sure the dip switches on

the receiver and wall transmitter are set to the same

frequency. (Fig. 13)

Step 1. Insert the receiver into the ceiling mounting

bracket with the at side of the receiver facing the

ceiling. (Fig. 14)

For best performance, make sure the Black antenna,

on the end of the receiver, remains extended and not

tangled with any of the electrical wires.

Step 2. Motor to Receiver Electrical connections:

Connect the black wire from the fan to the black wire

marked “TO MOTOR L” on the receiver. (Fig. 15)

Fig. 14

Fig. 13

Fig. 12

Receiver

Hanger

bracket

Hanger bracket

Safety cable Attach safety cable

to ceiling joist with

screw and washer

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Outlet box

Black (hot)

Black ("AC IN L")

Receiver

White (neutral)

White ("to motor N")

Ground

(green)

Black ("to motor L")

Blue (for light)

Black (motor)

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screw

(Connect to ground

wire on hanger

bracket if no house

ground wire exists.)

Connect the white wire from the fan to the white wire

marked ”TO MOTOR N” from the receiver. Connect the

blue wire from the fan to the blue wire marked ”FOR

LIGHT” from receiver. Secure all the wire connections with

the plastic wire nuts provided.

Step 3. Receiver to House Supply Wires Electrical

Connections: Connect the black (hot) wire from the ceiling

to the black wire marked “AC in L” from the receiver.

Connect the white (neutral) wire from the ceiling to the

white wire marked ”AC in N” from the Receiver. Secure

the wire connections with the plastic wire nuts provided.

(Fig. 15)

Step 4. If your outlet box has a ground wire (green or

bare copper) connect it to the fan ground wires; otherwise

connect the hanging bracket ground wire to the mounting

bracket. Secure the wire connection with a plastic nut

provided. After connecting the wires, spread them apart

so that the green and white wires are on one side of the

outlet box and black and blue wires are on the other side.

Carefully tuck the wire connections up into the outlet box.

(Fig. 15)

NOTE: Fan must be installed at a maximum distance

of 30 feet from the wall transmitter for optimal signal

transmission between the transmitter and the fan’s

receiver unit.

8. FINISHING THE INSTALLATION

Step 1. Tuck all the connections neatly into the ceiling

outlet box.

Step 2. Remove one screw from ceiling mounting bracket,

and loosen but do not remove the other screw, slide the

canopy up to the mounting bracket and place one of the

key hole slots over the mounting screw on the mounting

bracket. Rotate the canopy until the screw head locks in

place at the narrow section of the key hole. (Fig. 16)

Step 3. Align the remaining circular hole on the canopy

with the remaining hole on the Ceiling Mounting Bracket.

Insert and tighten the mounting screw from step 2 above.

Now, attach the canopy cover to the mounting screw head

by inserting the screw heads into the bottom side of the

canopy cover and rotating the cover clockwise.

NOTE: Adjust the canopy screws as necessary until the

canopy and canopy cover are snug. (Fig. 16)

Fig. 16

Fig. 15

60” Rana™

9. ATTACHING THE FAN BLADE/

BLADE ARM ASSEMBLIES

Attach each blade assembly to the motor by using

two mounting screws for each blade assembly.

(Fig. 17)

NOTE: Make sure these mounting screws are

securely tightened.

10. INSTALLING THE LIGHT KIT PAN

Step 1. Remove one screw from the black bracket

below fan motor assembly and loosen but do not

remove the other two screws. (Fig. 18)

Step 2. Push the light kit pan up to the fan motor

assembly so that the two loosened screw heads

t into the keyholes slots. Turn the light kit pan

clockwise. (Fig. 19)

Step 3. Re-install the screw that was removed in

step 1. (Fig. 19)

NOTE: Make sure these mounting screws are

securely tightened.

Screws

Light kit pan

Screws

Fig. 19

Fig. 18

Fig. 17

Screws

Blade arm Blade

This manual suits for next models

Table of contents

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting 300260/60-GENT Series User manual

Kichler Lighting

Kichler Lighting Pacific Edge 300157 User manual

Kichler Lighting

Kichler Lighting sterling manor select User manual

Kichler Lighting

Kichler Lighting Canfield Select User manual

Kichler Lighting

Kichler Lighting Select Dorset User manual

Kichler Lighting

Kichler Lighting Hatteras Bay Patio User manual

Kichler Lighting

Kichler Lighting Meredith User manual

Kichler Lighting

Kichler Lighting Terna 300215 User manual

Kichler Lighting

Kichler Lighting PINION 60 User manual

Kichler Lighting

Kichler Lighting FRYST User manual

Kichler Lighting

Kichler Lighting Jace LED User manual

Kichler Lighting

Kichler Lighting Monarch II Patio User manual

Kichler Lighting

Kichler Lighting Highland Manor User manual

Kichler Lighting

Kichler Lighting IMARI 300365SBK User manual

Kichler Lighting

Kichler Lighting 35155 User manual

Kichler Lighting

Kichler Lighting Olympia User manual

Kichler Lighting

Kichler Lighting Sunburst 300170 User manual

Kichler Lighting

Kichler Lighting Bead User manual

Kichler Lighting

Kichler Lighting 54 inch Skye User manual

Kichler Lighting

Kichler Lighting Lija User manual

Kichler Lighting

Kichler Lighting 35157 User manual

Kichler Lighting

Kichler Lighting Canfield User manual

Kichler Lighting

Kichler Lighting POLA User manual

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual