Kichler Lighting Maor 310136 User manual

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

65" Maor

A Kichler

Decor

™

ceiling fan

310136

3066708

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

3. WARNING: To reduce the risk of ﬁre or

electric shock, do not use this fan with any

solid-state speed control. Use only the

control provided with the fan.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. WARNING: To reduce the risk of ﬁre,

electric shock, or Personal Injury, mount

directly to a structural framing member or

to an outlet box marked 'Acceptable for

Fan Support of 22.7 kg (50 lbs) or less'. For

outlet box mounting, use mounting screws

provided with the outlet box.

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. To slide the reverse button to operate the

reverse function on this fan. A few seconds

later the fan will slow to a stop and then

reverse direction. NOTE: Fan will not operate

when the reverse switch in the middle.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

box.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the ground wire and white

(common) wire to one side with the black

(load) wire to the other side of the outlet

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

WARNING

To reduce the risk of ﬁre, electric shock, or

Personal Injury, mount directly to a structural

framing member or to an outlet box marked

'Acceptable for Fan Support of 22.7 kg(50 lbs)

or less'. For outlet box mounting, use mounting

screws provided with the outlet box.

3. PACKAGE CONTENTS

Unpack your fan and check the contents .

You should have the following items:

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

65"Maor

A. Mounting Bracket

B. Ball / Downrod Assembly (1)

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Blade Arm

H. Blade Holder

I. Blade

J. Switch Housing

K. Light Kit

L. LED Module

M. Glass Shade

N. Light Case

O. Package Hardware:

1) Mounting Hardware:

wood screws (2), ﬂat washers (2),

screws (2), lock washers (2),

wire nuts (3)

2) Blade Attachment Hardware:

screws (14)

3) Blade Arm Hardware:

screws (2)

4) Safety Cable Hardware:

wood screw (1), spring washer (1),

ﬂat washer (1)

5) Balance Kit

6) Screw Hardware

screws (3), ﬂat head screws (3)

7) Extra Screw Hardware

screws (3)

4. MOUNTING OPTIONS

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 30°ANGLE

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling.

A minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin installation. This is necessary for your

safety and also the proper programming of the

control system.

To properly install your ceiling fan, follow the

steps below.

Step 1. Before attaching fan to outlet box

(not included), ensure the outlet box is securely

fastened to at least two points to a structural

ceiling member (a loose box will cause the fan

to wobble). Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. Install mounting

bracket to outlet box in ceiling using the screws

and washers included with the outlet box or

screws and washers in the hardware bag.

(Fig. 5)

Step 4. Slip the coupling cover, canopy hole cover

and canopy onto the downrod. Carefully reinstall

the hanger ball onto the downrod . Make sure the

cross pin is in the correct position and the set

screws are tight and the wires are not twisted .

( Fig. 8)

Step 2. Remove the hanger ball from downrod

assembly by loosening set screws , removing

the cross pin, and twisting ball out of the rod.

( Fig. 6)

Step 3. Loosen the two set screws and remove

the clip and cross pin from the top coupling of

the motor body.

Carefully feed the fan wires up through the

downrod. Thread the downrod onto the motor

coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten

both set screws. (Fig. 7)

Flat Washer

Screw

Fig. 5

Ceiling Mounting Bracket

ETL Listed Outlet Box

Screw

Downrod

Cross Pin

Fig. 6

Set Screw

Hanger Ball

Fig. 7

Fig. 8

65"Maor

Set Screw

Cross Pin

Motor Body

Cross Pin

Clip

Set Screw

Clip

Hanger Ball

Canopy Hole Cover

Coupling Cover

Motor Body

Canopy

Step 5. Now lift the motor body into position

and place the hanger ball into the hanger bracket.

Rotate until the "Check Tab" has dropped into

the "Registration Slot " and seats ﬁrmly. ( Fig. 9)

The entire motor body should not rotate is this is

done correctly.

6 . INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

WARNING: Failure to properly seat the "Check

Tab" can damage the ceiling fan during operation.

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Drive a wood screw and washers into the

side of the brace that holds the outlet box. Leave

3mm (1/8") of space between the support brace

and the washer. (Fig. 10)

NOTE: Although the safety support cable is

required for Canadian installations only. It’s a good

idea to make the attachment with any installation.

Step 2. Insert the safety cable through the

mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the

safety cable to reach the screw and washers by

pulling the extra cable through the cable clamp

until the overall length is correct, put the end of the

cable back through the cabel clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the

safety cabel over the wood screw and under the

washer. Tighten the wood screw securely. (Fig. 11)

Fig. 9

Safety Cable Bolt

Wood Screw

Fig. 11

Fig. 10

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Check Tab Registration Slot

7. MAKE THE ELECTRIC CONNECTIONS

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electrician is

recommended to determine proper wiring.

Step1. Connect the fan supply BLACK wire

and fan light supply BLUE wire to the BLACK

household supply wire as shown in Fig. 12.

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts supplied with your fan. Secure

the connector with electrical tape. Make sure

there are no loose wire stands or connections.

Fig. 12

Fig. 13

Fig. 14

BLACK

WHITE

GREEN

Ground to

Mounting

Bracket

Green

Ground

Lead

Outlet Box

Ground

Conductor

WHITE

BLUE

BLACK

SUPPLY CIRCUIT

Mounting Bracket

Shoulder Screw

Canopy

Shoulder Screw

Step 1. Remove one of the two shoulder screws

in the mounting bracket. Loosen the second

shoulder screw without fully removing it.

(Fig. 13)

Step 2. Assemble canopy by rotating key slot in

canopy over shoulder screw in mounting bracket.

Tighten shoulder screw. Fully assemble and

tighten second shoulder screw that was

previously removed. (Fig. 14)

8 . FINISHING THE INSTALLATION

Step 4. After making all of the above

connecting, spread them apart so the GREEN

and WHITE wires to one side of the outlet box

and the BLACK wire toward the other side.

Step 3. Connect GROUND (GREEN) wires

from mounting bracket and downrod ball, to

GROUND (GREEN) or BARE (COPPER) from

house. (Fig. 12)

Step 2. Connect the fan neutral WHITE wire to

the household neutral WHITE wire as shown in

Fig. 12.

65"Maor

9. ATTACHING THE FAN BLADES

Step 3. Securely attach and tighten the canopy

hole cover over the shoulder screws in the

mounting bracket utilizing the keyslot twist-lock

feature. (Fig. 15)

NOTE: Before continuing , make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Position the blade over the blade holder

with three threaded posts showing. Make sure

the bottom edge of the blade is fully seated

against the blade holder. Attach the blade arm to

the blade and blade holder using the three blade

screws. Do not tighten blade screws until all three

have been inserted. Then, tighten each blade

screws securely. Repeat the procedure for all

remaining blades. (Fig.16)

Step 2. Fasten blade assembly to the holes

located on the bottom of the ﬂywheel. Tighten the

two "pre- installed" motor screws in the blade

arm. Repeat steps for the remaining blades

assemblies. (Fig. 17)

Fig. 15

Fig. 16

Fig. 17

Canopy Hole Cover

Shoulder Screw

Blade

Blade Screw

Blade Arm

Blade Holder

Motor Body

Blade Arm

Flywheel

10. INSTALLING THE SWITCH HOUSING

Step 1. Remove the screw nearest the red dot label

on the mounting ring and loosen the other two (do

not remove). Let the 9-pin connector from motor

body through the middle hole of switch housing.

Align the two slot holes on the switch housing over

the 2 screws previously loosened from the mounting

ring. Turn the switch housing until it locks in place at

the narrow end of the key holes. Securely tighten all

three screws. (Fig. 18)

11. INSTALLING THE LIGHT KIT

NOTE: Before continuing installation, conﬁrm that

the power is still turned off at the main circuit

breaker or by removing the correct fuse. Turning

the power off using a wall switch is not sufﬁcient to

prevent electrical stock.

Step 4. Hold the LED module close to the light kit.

Connect the WHITE wires from the light kit and LED

module by pushing the connectors together. Follow

the same procedure with the BLACK wires. Align the

holes on the LED module and light kit and securely

tighten with three screws in hardware bag. (Fig. 20)

Mounting Ring

Switch Housing

Screw

Switch Housing

Light Kit

Screw

Light Kit

Screw

LED Module

Fig. 18

Fig. 19

Fig. 20

Step1. Remove 1 of the 3 screws on switch housing

and loosen the other 2 screws (do not remove).

(Fig. 19)

Step 2. The Square plastic wiring connector from the

motor body and light kit will only ﬁt together one way.

Match up the color on the side of each connector,

then push them together until the snap engages.

(Fig. 19)

Step 3. Align the key holes on the light kit with the 2

screws on the edge of the switch housing. Turn light

kit until it locks in place at the narrow end of the key

holes. Tighten the 2 screws and reinstall the third

screw, making sure all three screws are tight and

secure. (Fig. 19)

65"Maor

12. INSTALLING THE GLASS SHADE AND

LIGHT CASE

13. INSTALLING THE FOB

Step 1. Assemble the glass shade to the light kit

by twisting in a clockwise direction. Do not

overtighten. (Fig. 21)

Fig. 21

Fig. 22

Fig. 23

Step 2. Let the reverse switch and 2 pull chains

through the holes on the light case. Attach the

light case to the light kit by using the three ﬂat

head screws in hardware package. (Fig. 22)

Step 1. Attach the decorative pull chain fobs to

the chains comming out of the light case.

Refer to Fig. 23.

Check the ON/OFF operation of the light by

gently pulling on the light switch pull chain.

Check the operation of the fan by gently pulling

on the speed control switch pull chain.

The operation sequence is as follows:

1st pull – High

2nd pull – Medium

3rd pull – Low

4th pull – OFF

Your fan is shipped from the factory with the

reversing switch positioned to circulate air

downward. If airﬂow is desired in opposite

direction, turn the fan off and wait for the blades

to stop turning, then slide the reversing switch to

the opposite position, and turn the fan on again.

The fan blades will turn in the opposition

direction and reverse the airﬂow.

Light Kit

Screw

Reverse

Switch

Light Case

Light Kit

Glass Shade

Fob

Reverse

Switch

Table of contents

Other Kichler Lighting Fan manuals

Kichler Lighting

Kichler Lighting Select Dorset User manual

Kichler Lighting

Kichler Lighting Grace 300316 User manual

Kichler Lighting

Kichler Lighting 54 Skye LED User manual

Kichler Lighting

Kichler Lighting Lija User manual

Kichler Lighting

Kichler Lighting Canfield 300117WH User manual

Kichler Lighting

Kichler Lighting Bentzen User manual

Kichler Lighting

Kichler Lighting 35156 User manual

Kichler Lighting

Kichler Lighting Humble 300415 User manual

Kichler Lighting

Kichler Lighting Lacey User manual

Kichler Lighting

Kichler Lighting ETL User manual

Kichler Lighting

Kichler Lighting Hatteras Bay Patio User manual

Kichler Lighting

Kichler Lighting FERRON User manual

Kichler Lighting

Kichler Lighting Canfield Patio 310192 User manual

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB User manual

Kichler Lighting

Kichler Lighting Spyn Lite User manual

Kichler Lighting

Kichler Lighting Olympia User manual

Kichler Lighting

Kichler Lighting Select Sutter Place User manual

Kichler Lighting

Kichler Lighting Botella User manual

Kichler Lighting

Kichler Lighting 35166 User manual

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" User manual

Kichler Lighting

Kichler Lighting Decor Dorset User manual

Kichler Lighting

Kichler Lighting 52 inch Colerne LED User manual

Kichler Lighting

Kichler Lighting Terna 300215 User manual

Kichler Lighting

Kichler Lighting Renew Select User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual