Keysight N9032B PXA User manual

Option EXM, External Mixing Upgrade Kit

Keysight N9032B PXA

Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9032-90004

Edition

Edition 2, October 2021

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9032-90004 3

Option EXM, External Mixing Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider.

Introduction

This kit includes parts to upgrade a N9032B PXA signal analyzer to add option EXM, External

Mixing. This kit includes parts to upgrade a PXA regardless of frequency range option installed.

In addition to installing the hardware to support option EXM, a license for the following option will

also be installed:

— N9032B-EXM, External Mixing

Products Affected: N9032B PXA

Serial Numbers: All

To Be Performed By: (X) Keysight Factory

( ) Keysight Service Center

( ) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

1.5 Hours

1.0 Hoursa

4.0 Hoursa

a.To ensure that these newly installed options are functioning properly, the procedure that follows includes the

requirement of performing certain adjustments and performance verification tests. However, the completion of

these tests does not guarantee that the instrument meets all advertised specifications.

4Installation Note N9032-90004

Option EXM, External Mixing Upgrade Kit

Installation Kit Parts List

Quantity Description Keysight Part Number

1 Adapter- Coaxial Straight Female-SMA to Female-SMA, 50Ω1250-1666

1 Washer, Lock, Internal Tooth, ¼ inch 2190-0067

1 Nut-Hex-Double-Chamfer 1/4-36-THD.125-IN-THK, Stainless Steel 2950-0223

1 Cable Assembly, External Mixing, Front Panel (W30) N9020-20166

1 Cable Assembly, A13J8 to W30 (W29) N9020-20167

1 Label, Warning (for Top Brace) N9030-80018

17 Screw, M3 x 0.5, (6 mm long), flat head 0515-1946

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

Installation Note N9032-90004 5

Option EXM, External Mixing Upgrade Kit

Tools Required

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— ¼-inch open-end wrench

— Small flat blade screwdriver

—KeysightCalibrationand Adjustment Software

— Test equipment and computer supported by the N78111B PXA Calibration Application

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with > 3 GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

6Installation Note N9032-90004

Option EXM, External Mixing Upgrade Kit

Analyzer Disassembly

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that

attach the handle strap (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet (6).

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet

(4) in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

Figure 1 Instrument Outer Case Removal

If the instrument is placed on its face during any of the following procedures, be sure to use a soft

surface or soft cloth to avoid damage to the front panel, keys, or input connector.

Make sure any adapters on the front panel are removed.

Installation Note N9032-90004 7

Option EXM, External Mixing Upgrade Kit

Top Brace Removal

Refer to Figure 2. To remove the top brace (1), use the T-10 driver to remove the twelve screws (2)

(0515-0372) attaching the top brace to the chassis. Remove the wire hold down (as shown in

Figure 3). Remove and discard the seventeen screws (3) (0515-1946) attaching the top brace.

Figure 2 Top Brace Removal

8Installation Note N9032-90004

Option EXM, External Mixing Upgrade Kit

Figure 3 Wire Hold Down

Installation Note N9032-90004 9

Option EXM, External Mixing Upgrade Kit

Front Frame Assembly Removal

1. Remove the plastic side trim strips by inserting a small flat blade screwdriver between the

bottom of the trim strip and the frame. Then carefully working up the side of the trim strip to

remove it. Avoid scratching the front frame paint.

2. Refer to Figure 4. Using the T-10 driver, remove the twelve screws (1) (0515-1035), six on

each side, to detach the Front Frame Assembly from the chassis.

3. Refer to Figure 5. Pull the Front Frame Assembly carefully away from the chassis. Remove the

ribbon cable W1 from the motherboard. The cable has locking tabs on each side, pinch and

pull to release.

Figure 4 Front Frame Removal

Make sure any connectors on the front panel are removed.

W1 may have locking springs on each side. Depress the spring on each side of the connector to

remove from the motherboard.

10 Installation Note N9032-90004

Option EXM, External Mixing Upgrade Kit

Figure 5 Front Panel Cable

Table of contents

Other Keysight Measuring Instrument manuals

Keysight

Keysight CalPod 855 A Series User manual

Keysight

Keysight x series Quick start guide

Keysight

Keysight N9030B Installation and operation manual

Keysight

Keysight PNA-X N5241A Installation and operation manual

Keysight

Keysight M3102A PXIe User manual

Keysight

Keysight x series User manual

Keysight

Keysight PNA Series Quick start guide

Keysight

Keysight U2781A User manual

Keysight

Keysight E4416A User manual

Keysight

Keysight N6854A User manual

Keysight

Keysight FieldFox User manual

Keysight

Keysight PD1500A User guide

Keysight

Keysight N9912A User manual

Keysight

Keysight E4981A User manual

Keysight

Keysight M9703B User guide

Keysight

Keysight N432A User manual

Keysight

Keysight x series Quick start guide

Keysight

Keysight PNA E8362C User manual

Keysight

Keysight u1701b Manual

Keysight

Keysight N9030A Installation and operation manual

Keysight

Keysight M9709A User guide

Keysight

Keysight B2900A User manual

Keysight

Keysight N432A User manual

Keysight

Keysight 1146B User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

ADTEK

ADTEK MW-5 operating manual

Acterna

Acterna MS1400 Operation manual