Keysight N9030B Installation and operation manual
Option YAV
Y-Axis Video Out
Keysight N9030B PXA Signal Analyzer
Installation Note
Notices
© Copyright 2016 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9030-90086
Edition
Edition 1, February 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9030-90086 3
Option YAV Installation Kit
Option YAV Installation Kit
Products Affected: N9030B PXA Signal Analyzer
Serial Numbers: All
Options
To Be Performed By: (X) Keysight Service Center
(X) Personnel Qualified by Keysight
(X) Customer
Estimated Installation Time:
Estimated Adjustment and Verification Time:
0.5 Hours
0.5 Hours
4Installation Note N9030-90086
Option YAV Installation Kit
Introduction
This kit contains all of the instructions required to install Option YAV on a Keysight N9030B PXA
signal analyzer. Option YAV enables the ANALOG OUT port and provides various signal selections.
The rear panel ANALOG OUT port is present on all PXA signal analyzers, however Option YAV must
be enabled via a license file.
Contents
1. At the time of manufacture the hardware related to this option was fully
adjusted and the option performance was verified to be within its
warranted specifications. Within one year of the initial calibration date
of the instrument this option is fully calibrated with no further
adjustment or verification testing.
To determine the initial calibration date, locate the original calibration
certificate that was shipped with the instrument at the time of
purchase. The Date of Calibration is printed on the original calibration
certificate.
To ensure that this newly installed option has been installed properly,
the procedure that follows includes a functional check.
2. The latest revision of the X-Series signal analyzer software may be
downloaded from:
http://www.keysight.com/find/Xseries_software
3. This option is licensed for one instrument model/serial number
combination. The license key will only install on the designated
instrument.
Quantity Description Keysight Part
Number
1 Installation Note This note
1 Option Upgrade Entitlement Certificate 5964-5178
Installation Note N9030-90086 5
Option YAV Installation Kit
Tools Required for Installation
— Personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
Tools Required for Manual Operation Verification
— Voltmeter
— Test cable, BNC (used to connect voltmeter to the analyzer rear panel ANALOG OUT)
— Banana plug to BNC adapter (used to connect voltmeter to BNC cable)
Installation Procedure over USB
1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an
attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File to the root directory of the USB Storage Device.
6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new
hardware and may display the configuration menu shown in Figure 1. This menu may be
configured according to your preferences.
Figure 1 USB Storage Device Configuration Menu
6Installation Note N9030-90086
Option YAV Installation Kit
7. The signal analyzer will automatically consume the License File. (This may take a few minutes)
When the License File is consumed the Keysight License Manager will display a “Successful
License Installation” message similar to the one shown in Figure 2.
Figure 2 Successful License Installation
Alternate Installation Procedure
The License File can be manually installed over USB or LAN by placing the license file in the
following folder on the signal analyzer
C:\Program Files\Agilent\licensing
Verify the Installation
1. Cycle the power on the signal analyzer.
2. Press System, Show System to display a list of installed options.
3. Verify that the newly installed option appears on the list.
Installation Note N9030-90086 7
Option YAV Installation Kit
Manually Verify Operation
1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.
2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,
Center Frequency, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the
display at −25 dBm.
3. Press AMPTD, Ref Level, and key in −25 dBm. The displayed signal level should be at the top
graticule line.
4. Press Input/Output, Output, Analog Out, Screen Video.
5. Connect a voltmeter, set to measure DC volts, to the analyzer rear panel ANALOG OUT
connector.
6. The voltmeter should measure 1V.
7. Increase the Ref Level to −15 dBm. The signal should drop one graticule division on screen and
the voltmeter reading should be 0.9 V.
8. This test is sufficient to determine if the output circuitry is working properly for all Analog Out
signal selections.
8Installation Note N9030-90086
Option YAV Installation Kit
Utilities, Adjustments, and Performance Verification Tests
Calibration Software and specified test equipment is required to perform the adjustments, and can
be used to automate the performance verification testing. Information on how to obtain this
software can be found at
http://www.keysight.com/find/calibrationsoftware
Utilities Required
None
Adjustments Required
None
Performance Testing Required
None
A full calibration is required to assure the instrument meets all specifications
The end user must ultimately determine whether they want a full calibration to be performed after
the installation of this upgrade or not. If a full calibration is required, arrangements regarding the
level of calibration must be made between the end user and the calibration provider.
For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your
local Keysight office access the following URL, or if in the United States, call the following
telephone number:
http://www.keysight.com/find/assist
1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)
This information is subject to change
without notice.
© Keysight Technologies 2016
Edition 1, February 2016
N9030-90086
www.keysight.com
Other manuals for N9030B
4
Table of contents
Other Keysight Measuring Instrument manuals
Keysight
Keysight Y1301A User manual
Keysight
Keysight FieldFox User manual
Keysight
Keysight M9203A User guide
Keysight
Keysight N9912A User manual
Keysight
Keysight N9068A User manual
Keysight
Keysight x series Quick start guide
Keysight
Keysight MXA Series Installation and operation manual
Keysight
Keysight U1211A Manual
Keysight
Keysight E5063A User manual
Keysight
Keysight FieldFox A Series User manual
Keysight
Keysight E5071C ENA Series User manual
Keysight
Keysight N9913A User manual
Keysight
Keysight E4982A User manual
Keysight
Keysight N2804 User manual
Keysight
Keysight PXA N9030A Installation and operation manual
Keysight
Keysight PXA X Series Installation and operation manual
Keysight
Keysight 775D Service manual
Keysight
Keysight N5244AU- H29 Installation and operation manual
Keysight
Keysight N5221A Owner's manual
Keysight
Keysight CalPod 855 A Series User manual
