Keysight Technologies N9040B Installation and operation manual
Notice: This document contains references to Agilent.
Please note that Agilent’s Test and Measurement
business has become Keysight Technologies. For more
information, go to www.keysight.com.
Keysight Technologies
N9040B UXA Signal Analyzer
Option B2X, 255 MHz Analysis Bandwidth
Installation Note
Notices
© Copyright 2016 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9040-90017
Supersedes None
Edition
Edition 1, April 2016
Printed in USA/Malaysia
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
Installation Note N9040-90017 3
Option B2X, 255 MHz Analysis Bandwidth
Option B2X, 255 MHz Analysis Bandwidth
Introduction
This installation note explains how to install Option B2X, 255 MHz Analysis Bandwidth, into a UXA
signal analyzer.
The option is licensed for one instrument model number/serial number combination. The license
file that is downloaded from the web will only install on the designated instrument.
Products Affected UXA N9040B
Serial Numbers: All
To Be Performed By: (X) Keysight Service Center
( ) Personnel Qualified by Keysight
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
2.0 Hours
6.0 Hours
4.0 Hours
4Installation Note N9040-90017
Option B2X, 255 MHz Analysis Bandwidth
Contents
Tools Required
— Personal computer with internet access and USB port
— USB storage device with > 2 GB free memory
— T-10 TORX Driver
— T-20 TORX Driver
— Keysight Calibration and Adjustment Software, N7814A (revision E.16.00 or later required)
— Test equipment and computer supported by the Keysight Calibration and Adjustment Software
— UXA Signal Analyzer Service Guide, N9040-90006. Available online.
Quantity Description Keysight Part Number
1 Installation Note This note
1 Option Upgrade Entitlement Certificate 5964-5178
1 Wideband Analog IF assembly N9020-60043
1 Wideband Digital IF assembly N9020-60311
1 Flex Circuit, WB DIF to Flex Circuit Interconnect Bracket N9040-60045
1 Flex Circuit, WB AIF to Flex Circuit Interconnect Bracket N9040-60042
1 Bracket, Flex Circuit Interconnect N9040-00025
1 Spring Clip (for flex cable) N9040-00035
1 Cable Kit N9040-60070
4 Screw, Pan Head, M3 x 0.5 8 mm long 0515-0372
15 Screw, Flat Head, M3 x 0.5 6 mm long 0515-1946
Installation Note N9040-90017 5
Option B2X, 255 MHz Analysis Bandwidth
Initial Instrument Functionality Check
1. Power on the instrument and allow the instrument to boot up, run the alignments and display
the measurement screen. The instrument will probably display a spectrum analyzer screen and
you will see the instrument sweeping.
2. There should be no alignment failures. If there are failures, investigate and fix the problem
before continuing.
6Installation Note N9040-90017
Option B2X, 255 MHz Analysis Bandwidth
Wideband Analog IF Assembly Hardware Installation
1. Power down the instrument, wait until the standby light comes on, and remove the power
cord.
2. Remove the instrument side strap handles, feet, outer case, top brace front, top brace rear,
and remove the rear panel (be careful to not damage the cables), and remove the rear brace.
See the UXA Service Guide Assembly Replacement Procedure section for A22 and A23 WB
Digital IF Boards. Save all screws for reuse.
3. Disconnect the gray ribbon cable from the rear motherboard. This cable runs from the front of
the instrument, and must be disconnected to allow the Wideband Analog IF to be installed.
4. Locate the Wideband Analog IF Assembly and the N9040-60042 Flex Circuit Cable in the kit.
Install the Flex Circuit cable into the connector on the Wideband Analog IF Assembly. This flex
cable will be connected to the other flex cable in the kit later in the installation process.
5. Install the Wideband Analog IF into card cage connectors J8 and J10. See Figure 1.
6. Locate 2, 0515-1946 flat head screws in the kit and secure the board brackets to the chassis
using these screws (1). Torque to 9 inch-pounds.
Figure 1 Wideband Analog I.F. Installed in Card Cage
7. Locate the gray coax cables in the kit. Find the short cable, W46, with color code 1 on one end,
and color codes 726 on the other end. Attach the color code 1 end of the cable to the
Wideband Analog IF at J1 as shown in Figure 1. Attach the other end of the cable to the
Reference board J726.
Installation Note N9040-90017 7
Option B2X, 255 MHz Analysis Bandwidth
8. Locate the W45 cable with color code 2 on one end and 17 on the other end. Attach color code
2 end to the Wideband Analog IF at J2. Route the cable as shown in Figure 2, the other end of
the cable will be routed later to the A3 Digital IF.
9. Locate the W34 cable with color code 4 at one end and color code 718 at the other end. Attach
the color code 4 end to Wideband Analog IF at J4, and the other end to A16 Reference
assembly at J718.
10.Locate W41 cable with color code 17 at one end and color code 901 at the other end. Attach
the color code 17 end to the Wideband Analog IF at J17, and the other end to A15 Front End
Controller at J901. Remove cable that is on A15J901, it will be discarded after the other end of
the cable at A3J15 is removed later.
11.Locate W40 cable with color code 18 at one end and color code 15 at the other end, Attach the
color code 18 end to the Wideband Analog IF at J18. The other end of the cable will be routed
to the A3 Digital IF assembly.
12.See Figure 2 that shows the hole in the chassis the W40 cable routes through in order to
connect to A3J15.
Figure 2 Cable Routing
Installation Note N9040-90017 9
Option B2X, 255 MHz Analysis Bandwidth
Wideband Digital IF Assembly Hardware Installation
14.See Figure 4. Locate the Wideband Digital IF assembly in the kit. Install the assembly into the
top card slot as shown.
Figure 4 Wideband Digital I.F. Installation
15.Locate the N9040-60045 Flex Circuit cable in the kit and connect one end to the Wideband
Digital IF assembly and the other end to the Flex Cable previously installed on the Wideband
Analog IF assembly.
16.Locate the "Bracket, Flex Circuit Interconnect" in the kit. This bracket secures the flex circuit
connection you made in the previous step. See Figure 4. attach the flex cable connection to
the interconnect bracket using the two flat head screws (1), and mount the interconnect
bracket to the instrument frame using a pan head screw (2) and torque to 9 inch-pounds.
10 Installation Note N9040-90017
Option B2X, 255 MHz Analysis Bandwidth
17.Locate the spring clip in the kit. Install the spring clip to secure the flex circuit connection on
the Wideband Digital IF assembly.
18.Re-install the Rear Brace and the Rear Panel. An additional flat head screw, 0515-1946 is
required to secure the new Wideband Digital IF assembly to the rear panel. This flat head
screw is in the bag of screws in the kit. Torque to 9 inch-pounds
19.Re install the front top brace and use the 0515-1946 flat head screws in the kit in the
countersunk locations. Torque to 9 inch-pounds.
20.Reinstall the rear top brace and outer case, side strap handles, and feet.
21.Power up the instrument. Assure the instrument passes the auto alignments
Other manuals for N9040B
1
Table of contents
Other Keysight Technologies Measuring Instrument manuals
Keysight Technologies
Keysight Technologies N9320A RF User manual
Keysight Technologies
Keysight Technologies B1505A User manual
Keysight Technologies
Keysight Technologies MXA Series Installation and operation manual
Keysight Technologies
Keysight Technologies N4373E User manual
Keysight Technologies
Keysight Technologies N9029AV01-V15 User manual
Keysight Technologies
Keysight Technologies X8712A User manual
Keysight Technologies
Keysight Technologies BT2152B Service manual
Keysight Technologies
Keysight Technologies U1731C User manual
Keysight Technologies
Keysight Technologies N5250C PNA Series User manual
Keysight Technologies
Keysight Technologies B1500A Installation guide
Keysight Technologies
Keysight Technologies N9030B Installation and operation manual
Keysight Technologies
Keysight Technologies M8131A User manual
Keysight Technologies
Keysight Technologies i7090 User manual
Keysight Technologies
Keysight Technologies N9020A Installation and operation manual
Keysight Technologies
Keysight Technologies N9020A Installation and operation manual
Keysight Technologies
Keysight Technologies UXA Installation and operation manual
Keysight Technologies
Keysight Technologies B1505A User manual
Keysight Technologies
Keysight Technologies N1060A User manual
Keysight Technologies
Keysight Technologies B2980A Series User manual
Keysight Technologies
Keysight Technologies InfiniiMax III Series User manual
