Keysight Technologies N9020B Manual

Option CR3, Second IF Out

Option CRP, Arbitrary IF Out

Keysight Technologies

N9020B MXA Signal Analyzer

N9010B EXA Signal Analyzer

N9048B PXE EMI Receiver

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90258

Edition

Edition 1, October 2018

Supersedes February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90258 3

Option CR3 or CRP Installation Kit

Products Affected: N9020B MXA Signal Analyzer

N9010B EXA Signal Analyzer

N9048B PXE EMI Receiver

Serial Numbers: All

Options

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4Installation Note N9020-90258

Option CR3 or CRP Installation Kit

Introduction

This kit contains all of the instructions required to install Option CR3 or CRP on a Keysight MXA or

EXA signal analyzer or PXE EMI receiver that already has the necessary hardware installed. If the

necessary hardware is not already installed, a different upgrade kit should be used.

To install this kit, the analyzer must already have both of the following:

— A rear panel AUX IF OUT port

— A compatible Front End Controller assembly installed.

Some analyzers will have an AUX if OUT port, but will not have a compatible Front End Controller

assembly.

To verify if a compatible Front End Controller assembly is installed, press System, Show Hardware.

Refer to the row for the Front End Controller and note the Hw Id entry.

If the Front End Controller’s Hw Id is 41 or 75, you may proceed with the installation of this kit.

If the option being installed is Option CRP and the Front End Controller’s Hw Id is not either 41 or

75, do not install this kit. Instead, install the N9010BU-HL3 kit or N9020BU-HL3, as appropriate.

If the option being installed is Option CR3 and the Front End Controller Hw Id is either 41, 75, or

170, you may proceed with the installation of this kit.

If the option being installed is Option CR3 and the Front End Controller Hw Id is not either 41, 75, or

170, do not install this kit. Instead, install the N9010BU-HL3 kit or N9020BU-HL3 kit, as

appropriate.

1. At the time of manufacture the hardware related to this option was fully

adjusted and the option performance was verified to be within its warranted

specifications. Within one year of the initial calibration date of the instrument

this option is fully calibrated with no further adjustment or verification testing.

To determine the initial calibration date, locate the original calibration

certificate that was shipped with the instrument at the time of purchase. The

Date of Calibration is printed on the original calibration certificate.

To ensure that this newly installed option has been installed properly, the

procedure that follows includes a functional check.

2. The latest revision of the X-Series Signal Analyzers software may be

downloaded from

http://www.keysight.com/find/xseries_software

If a software update is required, perform the software update BEFORE

following the procedure in this document for redeeming and installing the

option upgrade license key.

3. This option is licensed for one instrument model/serial number combination.

The license key will only install on the designated instrument.

Installation Note N9020-90258 5

Option CR3 or CRP Installation Kit

Contents

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Tools Required for Manual Operation Verification

— Spectrum Analyzer capable of measuring a 322.5 MHz signal at -40 dBm

— Test cable, sma or 3.5 mm connectors

— Adapters as needed to connect the cable between the spectrum analyzer and sma AUX IF OUT

port on the rear panel of the signal analyzer.

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB storage device.

6. Connect the USB storage device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Quantity Description Keysight Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

6Installation Note N9020-90258

Option CR3 or CRP Installation Kit

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

Installation Note N9020-90258 7

Option CR3 or CRP Installation Kit

Functional Check:

Within one year of the initial calibration date of the instrument this option is fully calibrated with no

further adjustment or verification testing. To ensure that this newly installed option has been

enabled correctly the following functional check is recommended.

1. Tap the message balloon at the bottom of the main display. This will remove out-of-date

errors. Tap Xto close the error history window.

2. Press System, Alignments, Align Now, All. Tap Xto close the align now window.

3. Watch for any errors during the instrument alignment.

4. Tap the message balloon at the bottom of the main display to view the instrument error log.

5. Verify that there were no errors during the alignment. Tap Xto close the error history window.

8Installation Note N9020-90258

Option CR3 or CRP Installation Kit

Manually verify operation

Option CR3, Second IF Output

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

key in 50 MHz. Tap Span, Zero Span. You should see a flat line across the display at -25 dBm.

3. Enable Option CR3. Press Input/Output, Output, Aux IF Out, Second IF Out.

4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate

adapters.

Spectrum analyzer settings:

Center frequency: 322.5 MHz

Span: 1 MHz

Bandwidth: 100 kHz

The spectrum analyzer should display a −33 dBm ±5 dB signal

Option CRP, Arbitrary IF Output

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

key in 50 MHz. Tap Span, Zero Span. You should see a flat line across the display at -25 dBm.

3. Enable Option CRP. Press Input/Output, More, Output, Aux IF Out, Arbitrary IF. Tap Arbitrary IF

Freq. Set the Arbitrary IF Out frequency to 70 MHz.

4. Connect a spectrum analyzer to the rear panel Aux IF Out port using test cable and appropriate

adapters.

Spectrum analyzer settings:

Center frequency: 70 MHz

Span: 1 MHz

Bandwidth: 100 kHz

The spectrum analyzer should display a −33 dBm ±5 dB signal

Installation Note N9020-90258 9

Option CR3 or CRP Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can

be used to automate the performance verification testing. Information on how to obtain this

software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

Edition 1, October 2018

N9020-90258

www.keysight.com

Other manuals for N9020B

This manual suits for next models

Table of contents

Other Keysight Technologies Measuring Instrument manuals

Keysight Technologies

Keysight Technologies B1505A User manual

Keysight Technologies

Keysight Technologies N774 C Series User manual

Keysight Technologies

Keysight Technologies U1733C User manual

Keysight Technologies

Keysight Technologies E8364-60108 Installation and operation manual

Keysight Technologies

Keysight Technologies FieldFox N9913A User manual

Keysight Technologies

Keysight Technologies N9340B User manual

Keysight Technologies

Keysight Technologies M9485A User guide

Keysight Technologies

Keysight Technologies M8131A User manual

Keysight Technologies

Keysight Technologies N9030B Installation and operation manual

Keysight Technologies

Keysight Technologies N432A User manual

Keysight Technologies

Keysight Technologies U9361F User manual

Keysight Technologies

Keysight Technologies B1500A Instruction Manual

Keysight Technologies

Keysight Technologies U5855A User manual

Keysight Technologies

Keysight Technologies N7373C Manual

Keysight Technologies

Keysight Technologies M980xA PXIe User manual

Keysight Technologies

Keysight Technologies N5245-60106 Installation and operation manual

Keysight Technologies

Keysight Technologies N7020A User manual

Keysight Technologies

Keysight Technologies E5868A Assembly instructions

Keysight Technologies

Keysight Technologies FieldFox N9927-90002 User manual

Keysight Technologies

Keysight Technologies MXA N9020A-508 User manual

Keysight Technologies

Keysight Technologies N5221B User manual

Keysight Technologies

Keysight Technologies P5000A Series User manual

Keysight Technologies

Keysight Technologies E8740A Operation manual

Keysight Technologies

Keysight Technologies N9340B User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual