Kane CO2 User manual
Instruction Manual
KANE-CO2
Indoor Carbon
Dioxide Monitor
Inventory No: MAN00134
Rev.: 0.00000
January 2021
1
1
1
2
3
3
4
5
6
7
12
14
Contents
Getting Started
Packing List
Features at a Glance
Overview
General Operation & Settings
Operating Instructions
LCD Display
Trend Chart Display
Max/Min
Main Menu Functions
Specifications
Appendix
Features:
•Large Display
•Touch Button Operation
•15° Bevel Design, Easy to Read
•Low Drift NDIR Sensor, Long Lifespan
•Audible & Visible Alarm
•Chart with Variable Time Zoom Levels
•CO2/RH/Temperature Monitor Tracer
•Auto-Calibration & Manual Calibration
•Max/Min Value Display in Certain Time
Thank you for purchasing our desktop KANE-CO2 monitor. This product is used to
monitor CO2 concentration, humidity(RH) & temperature(TEMP) for indoor
air quality monitoring
Getting Started
Contents:
•CO2 Monitor Unit
•USB Cable for Power
•User Manual
•AC Adapter (Optional)
1
1
3
4
5
6
8
7
2
11
12
13
14
15
16
15
16
10
9
Front Panel Good Level
Low Level
Hole for Rope
Hole for Screws
USB Port
LCD
Button
Button
Button
Button
Power Indicator
High Level
Item ItemDescription Description
Overview
Drawing Sketch & Components List
Hole for Sensors
Hole for Buzzer
Label
1
3
4
5
6
8
7
10
11
12
9
213
14
2
•Use provided USB cable to connect the device. Once the countdown is complete,
your device is ready to use. See detail in Page 3.
•Use & buttons to switch timeline & CO2/RH/TEMP. The trend chart
displays the history records for any of the three parameters. See detail in Page 5.
•To restore factory defaults, hold for 4 seconds until an audible beep is heard.
•Press once will bring up the main menu. To select the function, press /
button. See detail in Page 7.
•Select to switch human and plants modes. See detail in Page 8.
•Select to change the high/low alarms for human and plant . See detail in
Page 11.
•Enter to switch alarm and mute . See detail in Page 8.
•Enter to switch temperature units C and F. See detail in Page 10.
General Operation & Settings
Operating Instructions
1. When first unboxing, plug in the unit with the
provided USB cable as shown on the right.
2. Once successfully connected, the power indicator
& 3 LEDs flash one by one.
3. Main display shows a countdown from 10.
Once the countdown is complete, your
product is ready to use. No initial setup
or calibration is needed
3
19
20
21
22
23
24
25
26
27
ItemItem Name Name
CO2/RH/TEMP Chart
Max Reading of Chart
Min Reading of Chart
RH Reading
Main Menu
CO2 Reading
Time per Division - indicates the
Plant Mode
Human Mode
Audible Alarm On/Off
17
18
Temperature Reading C / F
o o
chart’s span of time
4
17
18
19
20
21
22
23
24
25
26
27
LCD Display
The below chart displays the past readings for any of the three parameters (CO2/RH
/TEMP). There are 4 modes that can be toggled by using key: CO2, TEMP, RH,
& Cycle(automatically cycles through CO2/TEMP/RH)
Press will toggle the available Zoom Levels for each parameters.
(Minute/Hour/Day/Week)
Trend Chart Display
Press Press Press
Press
Press
Press
Press
Press
5
Zoom Level (Time Span) Time per Division
1M (minute) 5sec /div
1H (hour) 5m / div
1D (day) 2h / div
1W (week) 0.5d / div
Max / Min
Below is a table that shows the available Zoom Levels for all parameters CO2/RH/
TEMP, as well as the duration of each division for corresponding Zoom Levels:
At the top right corner of the display, there are two numerical indicators: MAX &
MIN. As the Zoom Level is changed, the MAX & MIN values will reflect the
maximum & minimum values on the chart of the selected parameter
(CO2, RH & TEMP).
6
The Main Menu functions can be actived by pressing . Pressing / once
will bring up the main menu, with an underlining flashing bar indicating the
current choice.
Main Menu Functions
Press
Press
Press
No pressing any
button in 1 minute
/ Press
/
Press
/
Press
/
Press
Press
7
Select number 0 to enter human mode. 0 is defaulted as human mode, unchangeable.The
preset Low & high alarm are 800 & 1200ppm. Enter "ADV" to adjust them if necessary.
In plant mode, it allows user to select between types of plants for optimal setting by using
/ cycles through 1~9. See number references with corresponding alarm settings in
high & low alarms in Page 14.
When ALARM display , an audible alarm will sound if the CO2 level exceeds
preset CO2 alarm value; means MUTE.
To select the function, press when it is underlined by the flashing bar. Note that
after 30 seconds if nothing is pressed, the Main Menu will disappear & the device
will revert to the normal state.
Press /
Press
Press (main interface)
(main interface)
Press
Press
Function Description
ALARM
PLANT
Press
Press
Press
PressPress
Press
PressPress
Press
Press
Main
interface
8
Press
Press
Table of contents
Other Kane Measuring Instrument manuals
