Jung 230061SR User manual
Switch actuator / blinds actuator
Switch actuator, 6-gang / blinds actuator, 3-gang
Art. no.: 230061SR
Switch actuator, 16-gang / blinds actuator, 8-gang
Art. no.: 230161SR
Switch actuator, 24-gang / blinds actuator, 12-gang
Art. no.: 230241SR
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
The device may not be opened or operated outside the technical specifications.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Danger of electric shock on the SELV/PELV installation. Do not connect loads for mains voltage
and SELV/PELV together to the device.
For parallel connection of several motors to an output it is essential to observe the correspond-
ing instructions of the manufacturers, and to use a cut-off relay if necessary. The motors may be
destroyed.
Use only venetian blind motors with mechanical or electronic limit switches. Check the limit
switches for correct adjustment. Observe the specifications of the motor manufacturers. Device
can be damaged.
Do not connect any three-phase motors. Device can be damaged.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1: Device components
(1) Button field for manual operation
(2) Programming button and LED
(3) KNX connection
(4) Status LEDs for outputs
(5) Load connections (relay outputs)
1 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed tech-
nical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
The function of this device depends upon the software. Detailed information on loadable soft-
ware and attainable functionality as well as the software itself can be obtained from the manu-
facturer´s product database.
The device can be updated. Firmware can be easily updated with the Jung ETS Service App
(additional software).
The device is KNX Data Secure capable. KNX Data Secure offers protection against manipula-
tion in building automation and can be configured in the ETS project. Detailed specialist know-
ledge is required. A device certificate, which is attached to the device, is required for safe com-
missioning. During mounting, the certificate must be removed from the device and stored se-
curely.
Planning, installation and commissioning of the device are carried out with the aid of the ETS,
version 5.7.3 and above.
Intended use
– Switching of electrical loads with potential-free contacts
– Switching of electrically-driven Venetian blinds, roller shutters, awnings and similar
hangings
– Mounting on DIN rail according to EN 60715 in small distribution boards
Product characteristics
– Outputs can be operated manually, construction site mode
– Feedback in manual mode and in bus mode
– Disabling of individual outputs manually or by bus
– Status feedback (e. g. wind alarm)
– KNX Data Secure compatible
– Updateable with Jung ETS Service App
Characteristics switch operation
– Operation as NO or NC contacts
– Feedback function
– Logic and restraint function
– Central switching functions with collective feedback
– Time functions: switch-on delay, switch-off delay, staircase lighting timer with run-on time
– Scene function
– Operating hours counter
Characteristics blinds operation
– Suitable for AC motors 110...230 V
– Operating modes "Venetian blind with slats", "Roller shutter/awning", "Venting louver/roof
window"
– Blind/shutter position directly controllable
– Slat position directly controllable
– Feedback of movement status, blind/shutter position and slat position
– Forced position through higher-level controller
– Safety function: 3 independent wind alarms, rain alarm, frost alarm
– Sun protection function with heating/cooling operation
– Disabling function (lock-out protection)
– Scene function
2 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
Logic function characteristics
– Logic gates
– Transformer (conversion)
– Disabling element
– Comparator
– Limit value switch
4 Operation
Figure2: Operating elements
(4) Status LEDs for outputs
ON: Relay output closed
OFF: Relay output opened
Flashes slowly: output in manual mode selected
Flashes quickly: Output disabled via continuous manual mode
(6) Button ǃ
Manual operation
(7) LED ǃ
ON: continuous manual mode active / Flashing: temporary manual control active
(8) LED DŽ
ON: relay outputs closed, manual operation active
(9) Button DŽ
Short: switch on, adjust slats or stop.
Long: Move hanging upwards
(10) Button Dž
Short: switch off, adjust slats or stop.
Long: Move hanging downwards.
(11) LED Dž
ON: relay outputs open, manual control active
(12) Button ALL OFF
Open all relay outputs, stop drives
In operation with the button field the device distinguishes between a short and a long press.
– Short: actuation for less than 1 s
– Long: actuation of between 1 and 5 s
In switching operation, the device distinguishes between the operating modes "normally
open contact" and "normally closed contact". The buttons (9 + 10) change the switching
status when pressed:
Normally open contact: switch on = close relay, switch off = open relay
Normally closed contact: switch on = open relay, switch off = close relay
The LEDs (4 + 8 + 11) always indicate the relay status.
The LEDs (4) optionally indicate the status of the outputs only temporarily (depending on
the parameters).
3 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
Operating modes
– Bus operation: Operation via push-button sensors or other bus devices
– Temporary manual control: manual control locally with keypad, automatic return to bus
control
– Continuous manual mode: Exclusively manual operation on the device
No bus operation is possible in manual mode.
After a bus failure and restoration the device switches to bus operation.
The manual mode can be disabled in ongoing operation via a bus telegram.
Switching on the temporary manual control
Operation using the button field is programmed and not disabled.
￭ Press button ǃ (6) briefly.
LED ǃ (7) flashes, LEDs A1... (4) of the first configured output or output pair flash.
Short-time manual operation is switched on.
After 5 s without a key-press, the actuator returns automatically to bus operation.
Switching off temporary manual operation
The device is in short-term manual mode.
￭ No button-press for 5 s.
- or -
￭ Press ǃ (6) button briefly as many time as necessary until the actuator leaves the short-
time manual mode.
Status LEDs A1... (4) no longer flash, but rather indicate the relay status.
Short-time manual operation is switched off.
Switching outputs: depending on the programming, the output relays switch to the position
that is active after the manual mode is switched off, e.g. to the forced position, logic func-
tion.
Blind/shutter outputs: depending on the programming, the hangings move to the position
that is active after the manual mode is switched off, e.g. to the forced position, safety or
sun protection position.
Switching on permanent manual control
Operation using the button field is programmed and not disabled.
￭ Press the ǃ (6) button for at least 5 s.
LED ǃ (7) lights up, LEDs A1... (4) of the first configured output or output pair flash.
Continuous manual mode is switched on.
Switching off permanent manual control
The device is in continuous manual mode.
￭ Press the ǃ (6) button for at least 5 s.
LED ǃ (7) is off.
Continuous manual mode is switched off. Bus operation is switched on.
Switching outputs: depending on the programming, the output relays switch to the position
that is active after the manual mode is switched off, e.g. to the forced position, logic func-
tion.
Blind/shutter outputs: depending on the programming, the hangings move to the position
that is active after the manual mode is switched off, e.g. to the forced position, safety or
sun protection position.
4 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
Operating an output in manual mode
￭ Activate short-term or permanent manual operation.
￭ Press button ǃ (1) repeatedly until LED A1... (4) of the desired output or output pair
flashes.
￭ Press button DŽ (9) or Dž (10).
Short: Switch on/off, drive stop
Long: Move blind/shutter upwards/downwards
LED DŽ (3) ON: Relay output closed
LED Dž (6) OFF: Relay output opened
Short-term manual operation: After running through all of the outputs the device exits
manual mode after another brief press.
Switching off all outputs / Stopping all hangings
The device is in continuous manual mode.
￭ Press the ALL OFF button (7).
Switching outputs: All outputs switch off (NO operating mode: relay output opened/NC op-
erating mode: relay output closed).
Venetian blind outputs: All blinds/shutters stop.
Disabling outputs
The device is in continuous manual mode. The bus control can be disabled (ETS parameter).
￭ Press button ǃ (6) repeatedly until LED A1... (4) of the desired output or output pair
flashes.
￭ Press the/ DŽ (9) and / Dž (10) buttons simultaneously for approx. 5 s.
Selected output is disabled.
The status LED A1... (4) of the selected output or output pair flashes quickly.
A disabled output can be operated in manual mode.
Re-enabling outputs
The device is in continuous manual mode. One or more outputs were disabled in manual mode.
￭ Press button ǃ (6) repeatedly until the output to be unlocked or the output pair is selec-
ted.
￭ Press the/ DŽ (9) and / Dž (10) buttons simultaneously for approx. 5 s.
Disabling is deactivated.
The LED A1... (4) of the selected output or output pair flashes slowly.
5 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Disconnect the device. Cover up live parts.
5.1 Fitting and electrical connection
Fitting the device
In secure operation (preconditions):
– Secure commissioning is activated in the ETS.
– Device certificate entered/scanned or added to the ETS project. A high resolution camera
should be used to scan the QR code.
5 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
– Document all passwords and keep them safe.
Observe ambient temperature. Ensure adequate cooling.
￭ Mount device on DIN rail.
￭ In secure operation: The device certificate must be removed from the device and stored
securely.
Connecting the device
Figure3: Device connection (connection example):
￭ Connect the bus line with the KNX connecting terminal with the correct polarity.
￭ Attach the cover cap to the KNX connection as protection against hazardous voltages.
￭ For switched loads, configure the outputs as a switching output.
￭ For Venetian blind operation, configure the outputs as a Venetian blind output. Two adja-
cent relay outputs form a Venetian blind output.
Delivery state: The outputs can be manually operated. Outputs are set as venetion blind
outputs.
The total current capacity of neighbouring outputs is a maximum of 20 A.
Figure4: Total current capacity of neighbouring outputs
5.2 Commissioning
Load physical address and application program
￭ In Venetian blind operation: measure blind/shutter and slat travel times and enter them in
the parameter setting.
￭ Press the programming button.
6 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
The programming LED lights up.
￭ Load physical address and application program using the ETS.
Safe-state mode
The safe state mode stops the execution of the loaded application program.
Only the system software of the device is still functional. ETS diagnosis functions and pro-
gramming of the device are possible. Manual operation is not possible.
Activating the safe-state mode
￭ Switch off the bus voltage or remove the KNX device connection terminal.
￭ Wait about 15 s.
￭ Press and hold down the programming button.
￭ Switch on the bus voltage or attach the KNX device connection terminal. Release the pro-
gramming button only after the programming LED starts flashing slowly.
The safe-state mode is activated.
With a new brief press of the programming button, the programming mode can be
switched on and off as usual also in the safe-state mode. If Programming mode is active,
the programming LED stops flashing.
Deactivating safe-state mode
￭ Switch off bus voltage (wait approx. 15 s) or carry out ETS programming.
Master reset
The master reset restores the basic device setting (physical address 15.15.255, firmware re-
mains in place). The device must then be recommissioned with the ETS. Manual operation is
possible.
During secure operation: A master reset deactivates device security. The device can then be re-
commissioned with the device certificate.
Performing a master reset
Precondition: The safe-state mode is activated.
￭ Press and hold down the programming button for > 5 s.
The programming LED flashes quickly.
The device performs a master reset, restarts and is ready for operation again after ap-
prox. 5 s.
Restoring the device to factory settings
Devices can be reset to factory settings with the Jung ETS Service App. This function uses the
firmware contained in the device that was active at the time of delivery (delivery state). Restor-
ing the factory settings causes the devices to lose their physical address and configuration.
6 Technical data
Ambient conditions
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
KNX
KNX medium TP256
Commissioning mode S-mode
Rated voltage KNX DC 21 ... 32 V SELV
Current consumption KNX
Art.-no.: 230061SR, 230161SR 5 ... 18 mA
7 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
Art. no. 230241SR 5 ... 24 mA
outputs
Switching voltage AC 250 V ~
Switching current AC1 16 A
Fluorescent lamps 16AX
Current carrying capacity
Neighbouring outputs Ʃ 20 A
Loads per output
Ohmic load 3000 W
Capacitive load max. 16 A (140μ)
Motors 1380 VA
Switch-on current 200 μs max. 800 A
Switch-on current 20 ms max. 165 A
Lamp loads 230 V
Incandescent lamps 3000 W
HV halogen lamps 2500 W
HV-LED lamps max. 400 W
LV halogen lamps with electronic transformers 1500 W
LV halogen lamps with inductive transformer 1200 VA
Fluorescent lamps T5/T8
uncompensated 1000 W
parallel compensated 1160 W (140 μF)
twin-lamp circuit 2300 W / 140 μF
Compact fluorescent lamps
uncompensated 1000 W
parallel compensated 1160 W (140 μF)
Mercury vapour lamps
uncompensated 1000 W
parallel compensated 1160 W (140 μF)
Fitting width
Art. no. 230061SR 72 mm / 4 module
Art. no. 230161SR 144 mm / 8 module
Art. no. 230241SR 216 mm / 12 module
Weight
Art. no. 230061SR approx. 230 g
Art. no. 230161SR approx. 500 g
Art. no. 230241SR approx. 740 g
Clampable conductor cross-section
single stranded 0.5 ... 4 mm²
Finely stranded without conductor sleeve 0.5 ... 4 mm²
Finely stranded with conductor sleeve 0.5 ... 2.5 mm²
Connection torque screw terminals max. 0.8 Nm
8 / 9
82402603 15.05.2020
J0082402603
Switch actuator / blinds actuator
7 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
www.jung.de
9 / 9
82402603 15.05.2020
J0082402603
Other manuals for 230061SR
1
This manual suits for next models
2
Table of contents
Other Jung Controllers manuals
Jung
Jung 5201 HYG Series User manual
Jung
Jung HOME BTS1B2U User manual
Jung
Jung Smart Control SC 1000 KNX Operator's manual
Jung
Jung 240-10 User manual
Jung
Jung 2424 REG HE User manual
Jung
Jung 240-10 EB User manual
Jung
Jung FST 1240 EB User manual
Jung
Jung KNX 360061SR User manual
Jung
Jung 1741DSTE User manual
Jung
Jung FA 26 UP User manual
Jung
Jung 390041SR User manual
Jung
Jung Instabus 2134.16 REG User manual
Jung
Jung KNX 4093 KRM TS D User manual
Jung
Jung Smart Pilot 10 User manual
Jung
Jung eNet FM AS 16 REG User manual
Jung
Jung Smart Control 7 Operator's manual
Jung
Jung 2336 REG HZ B User manual
Jung
Jung 1713DSTE User manual
Jung
Jung KNX 390011 SU User manual
Jung
Jung FMST50UP User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
