Jung 1713DSTE User manual
Table of Contents
1 Safety instructions.............................................................................................................3
2 Intended use .....................................................................................................................3
3 Operation ..........................................................................................................................3
4 Information for electrically skilled persons ........................................................................5
5 Technical data...................................................................................................................8
6 Warranty............................................................................................................................9
2 / 9
82598933 19.08.2022
J0082598933
Power DALI push-button controller TW
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual
fully.
Danger of electric shock. Always disconnect before carrying out work on the device
or load. In so doing, take all the circuit breakers into account, which support danger-
ous voltages to the device and or load.
This manual is an integral part of the product, and must remain with the end cus-
tomer.
2 Intended use
– Switching and brightness setting for luminaires with DALI interface
– Setting the colour temperature for luminaires with DALI Device Type 8 for Tun-
able White in accordance with IEC 62386-209
– Mounting in appliance box with dimensions according to DIN 49073
– Operation with suitable cover from the systems LB management, JUNG
HOME, eNet and KNX RF
Since error-free interaction cannot be guaranteed in combination with other
DALI controls, it is thus not recommend.
Product characteristics
– DALI supply for a maximum of 18 DALI subscribers
– Parallel switching of up to 4 DALI control units with the option of supplying up
to 72 DALI subscribers
– Storing of minimum brightness, coldest and warmest colour temperature
– Switching on with the last set brightness/colour temperature or saved bright-
ness/colour temperature
– With 2-gang operating cover: adjustment of the colour temperature via right
rocker
3 Operation
These instructions describe operation with a LB Management push-button 1-gang
and LB Management push-button 2-gang. Operation with different covers is de-
scribed in the instructions for the cover in question. Operation using 2-wire or 3-wire
extension essentially corresponds to operation on the main device.
With a LB Management push-button 2-gang, the left rocker works like the LB Man-
agement push-button 1-gang. The right rocker is used to directly set the colour tem-
perature.
Power DALI push-button controller TW
3 / 9
82598933 19.08.2022
J0082598933
Switching the light
￭ Brief press on the operating cover: Light is switched on or off at the last set
brightness/colour temperature or a saved brightness/colour temperature.
￭ Long press on the operating cover at the bottom: Light is switched on at min-
imum brightness.
Adjusting the brightness
￭ Long press on the operating cover at the top or bottom.
Setting the colour temperature
￭ Press the operating cover in the switched-on state at the top, bottom or over
the entire surface twice within 0.4 seconds (double-click). The light switches
off and on again.
￭ Long press on the operating cover at the top or bottom.
After a further double click, the insert switches back to normal operation and
signals this with a short switching off and on again. After one minute without
operation, the insert also returns to normal operation.
With a LB Management push-button 2-gang the right rocker is used to directly
set the colour temperature.
Saving the switch-on brightness / colour temperature
￭ Set the brightness and colour temperature.
￭ Press operating cover over entire surface for longer than 4 seconds.
The light switches off and on again. The brightness and the colour temperat-
ure are saved.
Deleting the switch-on brightness
￭ Press the operating cover briefly: Light switches on at the saved switch-on
brightness and colour temperature.
￭ Press the operating cover for longer than 4 seconds: Switch-on brightness and
colour temperature are deleted.
When switching on, the brightness and colour temperature present prior to
switching off are set now.
Different operation with push-button extension
￭ Long press on the push-button: Adjust the brightness. Push-button: The ad-
justment direction is changed with each new long actuation.
￭ Double-click the push-button: The mode for changing the colour temperature
is called up. The direction of the change in colour temperature changes with
each new long actuation.
After one minute without operation, the insert returns to normal operation.
Power DALI push-button controller TW
4 / 9
82598933 19.08.2022
J0082598933
Saving a switch-on brightness is not possible.
4 Information for electrically skilled persons
DANGER!
Mortal danger of electric shock.
Before carrying out work on the device or load, disengage all the corresponding cir-
cuit breakers. Cover up live parts!
Connecting and fitting the device
Image1: Connection diagram with optional extensions
(1) DALI insert
(2) Cover interface with LED
(3) Button Test
(4) DALI subscriber
(5) 3-wire extension
(6) 2-wire extension
(7) Push-button, NO contact
Power DALI push-button controller TW
5 / 9
82598933 19.08.2022
J0082598933
DALI cable: type, cross-section and routing according to the specifications for 250 V
cables. DALI and mains voltage wires can be run together in a cable, e.g. NYM 5x1.5
mm².
￭ Connect the DALI insert (1) and the DALI subscriber (4) according to the con-
nection diagram (see figure 1).
￭ If multiple circuit breakers supply dangerous voltages to the device or load,
couple the circuit breakers or label them with a warning, to ensure disconnec-
tion is guaranteed.
A 3-wire extension can only control one DALI insert. Central control is not pos-
sible on several DALI inserts.
To increase the detection field of motion or presence detectors, up to 10
devices can be connected to the DALI insert via 3-wire extensions.
The connected DALI subscribers may be operated on different phases.
The connected lighting can also be switched without a cover by briefly press-
ing the Test button (3).
Image2: Terminal-specific cable cross-section
￭ When switching multiple DALI inserts in parallel, ensure correct polarity
(see figure 3).
Power DALI push-button controller TW
6 / 9
82598933 19.08.2022
J0082598933
Image3: Switching DALI inserts in parallel
Parallel switched DALI inserts cannot be operated with motion or presence de-
tector covers.
Adjusting the minimum brightness and colour temperature limits to the luminaire
Precondition: Light is switched on.
￭ Press the button Test (3) for longer than 4 seconds, until the LED (2) turns
green.
The connected luminaire switches to the currently set minimum brightness.
If the button Test is not pressed for more than 30 seconds, the setting mode is
automatically exited, the settings are applied and the LED goes out.
￭ To change the minimum brightness, press and hold the button Test for longer
than one second.
The LED flashes green and the luminaire starts to become brighter with min-
imum brightness.
￭ Once the desired minimum brightness is reached, release the button Test.
The LED lights up green. The minimum brightness is saved.
￭ To set the coldest colour temperature, press the button Test for less than one
second.
Power DALI push-button controller TW
7 / 9
82598933 19.08.2022
J0082598933
The LED lights up blue and the luminaire switches to the coldest colour tem-
perature.
￭ To change the coldest colour temperature, press and hold the button Test for
longer than one second.
The LED flashes blue and the luminaire slowly starts to warm up at the coldest
colour temperature (10,000 K).
￭ Release the button Test as soon as a change in the colour temperature is vis-
ible on the luminaire.
The LED lights up blue, the coldest colour temperature is saved.
￭ To change the warmest colour temperature, press and hold the button Test for
longer than one second.
The LED flashes red and the luminaire slowly starts to cool down at the
warmest colour temperature (2,000 K).
￭ Release the button Test as soon as a change in the colour temperature is vis-
ible on the luminaire.
The LED lights up red, the warmest colour temperature is saved.
￭ To exit the setting mode, briefly press the button Test again.
Resetting the insert to factory settings
Precondition: Load is switched off.
￭ Press the Test button for at least 20 seconds.
The red LED lights up.
￭ Release the button and press it briefly once again within 10 seconds.
The red LED flashes three times.
The insert is reset to default setting.
5 Technical data
Rated voltage AC 230 V~
Mains frequency 50 / 60 Hz
Power consumption max. 2.8 W
Rated voltage DALI DC 16 V (typ.)
Output current max. 36 mA
Short-circuit current max. 60 mA
Ambient temperature -5 ... +45 °C
Colour temperature setting 2,000 ... 10,000 K
Number of DALI subscribers max. 18
Number of parallel control units max. 4
Power DALI push-button controller TW
8 / 9
82598933 19.08.2022
J0082598933
Number of extension units
2-wire, push-button unlimited
3-wire extension, rotary extension 10
Total length of extension device cable max. 100 m
6 Warranty
The warranty is provided in accordance with statutory requirements via the specialist
trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: +49 2355 806-0
Telefax: +49 2355 806-204
www.jung.de
Power DALI push-button controller TW
9 / 9
82598933 19.08.2022
J0082598933
Other manuals for 1713DSTE
1
Table of contents
Other Jung Controllers manuals
Jung
Jung RCD 20 series User manual
Jung
Jung FA 14 REG User manual
Jung
Jung 4093 KRM TS D Operator's manual
Jung
Jung eNet FM AS 16 REG User manual
Jung
Jung KNX 519 KRMTSD Series User manual
Jung
Jung eNet FMAS10UP User manual
Jung
Jung FA 10 REG User manual
Jung
Jung 390041SR User manual
Jung
Jung 2204 REG User manual
Jung
Jung KNX User manual
Jung
Jung FCA 2 REGHE User manual
Jung
Jung Smart Control IP Guide
Jung
Jung 2178 Series User manual
Jung
Jung 230061SR User manual
Jung
Jung KNX 2095 LUX User manual
Jung
Jung FM ST 50 UP User manual
Jung
Jung eNet FMAS26UP User manual
Jung
Jung KNX 2095 LUX User manual
Jung
Jung FAJ 6 UP User manual
Jung
Jung FST1240EB User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
