Jung FMAS16REG User manual
eNet radio switch/push-button actuator 1-gang, for rail mounting
eNet radio switch/push-button actuator 1-gang, for rail mounting
Art. No. : FMAS16REG
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled
persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. In so doing, take all the circuit breakers into account, which support dangerous
voltages to the device and or load.
Danger of electric shock. During installation and cable routing, comply with the
regulations and standards which apply for SELV circuits.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Fire hazard! Operation exclusively with the power supplies listed under accessories
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Device components
(1) Load connection
(2) Operating mode switch
(3) Button Prog
(4) Status LED
(5) Bus line connection
3 Function
Intended use
- Switching of lighting
- Operation with suitable eNet radio transmitters
1/12
82581723
J0082581723 23.03.2017
- Operation with power supply RMD and receiver module RMD cover or eNet server (see
accessories)
- Installation in distribution boxes on DIN rail according to EN 60715
Product characteristics
- Operating mode switch for switching/push-button actuator switch-over or parameterisation
via eNet server
- Status feedback to radio transmitter
- Scene operation possible
- Switchable output with Prog button
- Status indicator via LED
Switching operation:
- Switch-on telegram: Device switches on
- Switch-off telegram: Device switches off
Push-button operation:
- Relay contact remains closed as long as ON or OFF telegrams are being received
- The maximum switch-on time is 60 seconds
Can be set with eNet server:
- Flash function
- Run-on time
- Switch-on delay / switch-off delay
- Operation as NO or NC contacts
- Switch-off warning
- Minimum switching repeat time
- Operation locks
- Continuous on, Continuous off
Supplementary functions with eNet Server:
- Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
- Update of the device software
- Reading of error memory
Behaviour in case of bus voltage failure and return
If the bus voltage fails, the actuator switches off. The response to bus voltage return can be
parameterised with eNet server. Default setting: Off.
4 Operation
iWhen operating with the eNet Server, operation and signalling could vary from what is
described here.
Operation with radio transmitters
Operation is with radio transmitters, please observe the radio transmitter instructions.
Operation with Prog button
oPress Prog button briefly.
The load switches on or off.
Status LED lights up: output is switched on.
Status LED off: output is switched off.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live
parts in the working environment.
2/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Fitting the device
oMount device on DIN rail. Output terminals must be at the top.
Connect bus line
Figure 2: Connection diagram of bus line
Labelling / Colour Connection
DC– / GY dark grey Power supply –
DC+ / RD red Power supply +
Bus– / WH white Data cable –
Bus+ / YE yellow Data cable +
As bus line, use e.g. J-Y(St)Y 2x2x0.8
oConnect the device with bus line (figure 2) to the RMD reception module and power supply
(see instructions of RMD reception module and power supply).
3/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Connecting loads
Figure 3: Connection example
oConnect device as shown in the connection example (figure 3).
Presetting the operating mode
Figure 4: Operating mode switch
Switch position Function
PC Operating mode and parameter set with eNet
server.*)
MPush-button operation
KSwitching operation
*) If the operating mode switch is turned from the position PC to another operating mode, the
parameters are set to the default setting. The settings made with the eNet Server will be
lost.
Mains voltage is switched off.
oSet the operating mode switch.
4/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
5.2 Commissioning
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
During commissioning, cover the parts carrying voltage on radio transmitters
and actuators and in their surrounding area.
iThe actuator can also be commissioned with eNet Server as an alternative to the
commissioning described here.
Connecting actuator to radio transmitters
Load is switched off.
oPress the Prog button for longer than 4 seconds.
The load switches on.
The status LED flashes after 4 seconds and the load switches off. The actuator is in
programming mode for approx. 1 minute.
oSwitch radio transmitter to programming mode (see radio transmitter instructions).
oTrigger telegram on the radio transmitter.
The status LED of the actuator lights up for 5 seconds.
The actuator is connected to the radio transmitter. The actuator and radio transmitter exit
the programming mode automatically.
iIf the status LED of the actuator flashes 3 times at 1-second intervals for approx.
5 seconds, then the programming operation was not successful. All the memory locations
in the actuator or radio transmitter are occupied.
iAll On and All Off buttons of a radio transmitter are connected to the actuator automatically
as soon as the first connection to the radio transmitter takes place.
iScene buttons must be connected separately.
Disconnecting connection to a radio transmitter
oCarry out the same steps as when connecting (see Connecting actuator to radio
transmitters).
The status LED flashes quickly for 5 seconds. The actuator is disconnected from the radio
transmitter. The actuator and radio transmitter exit the programming mode automatically.
iIf there several connections or scene buttons for a radio transmitter, all connections must
be disconnected individually.
iAll On and All Off buttons of a radio transmitter are disconnected automatically as soon as
the last connection of the corresponding output to the radio transmitter is disconnected.
Manual disconnection is not possible.
Resetting the device to the factory setting
All connections to radio transmitters are disconnected and parameters are reset to default
setting. If the operating mode switch is on PC, switching operation is set.
iThe connections in the radio transmitters are preserved and must be deleted separately.
Load is switched off.
oPress the Prog button for at least 20 seconds.
The load switches on.
The status LED flashes after 4 seconds and the load switches off. The status LED flashes
faster after 20 seconds.
oRelease Prog button and press briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
The device is reset to default setting.
5/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
6 Appendix
6.1 Technical data
Rated voltage AC 230V~
Mains frequency 50 / 60Hz
Ambient temperature -5 ... +45°C
Switching current for AC 230 V ~
Ohmic 16A
For switching current >10A connecting cable 2.5mm²
Fluorescent lamps 4AX
Minimum switching current AC 100mA
Contact type µ
Standby power max. 0.2W
Connected load
Incandescent lamps 2300W
HV halogen lamps 2000W
Electronic transformers 1500W
HV-LED lamps typical 500W
Compact fl lamp. typical 500W
Inductive transformers 1000VA
Fluorescent lamps, uncompensated 920VA
Capacitive load 690VA (560 µF)
Connection of load terminals
single stranded 1.5 ... 4mm²
Finely stranded without conductor sleeve 0.75 ... 4mm²
Finely stranded with conductor sleeve 0.5 ... 2.5mm²
Fitting width 36mm / 2modules
Bus line
Rated voltage DC 12VSELV
Current consumption max. 20mA
Connection, Bus device connection terminal
Cable length max. 3m
6.2 Parameter list
The device parameters can be changed with the eNet server:
Device and channels
Parameters Setting options, Basic
setting
Explanations
Function Light, switching, unused
Basic setting: Light
Light
The channel is integrated for
the "Lighting" central function
in the eNet SMART HOME
app.
Switching
The channel is not integrated
in any central function.
Unused
The channel is not displayed
in the eNet SMART HOME
app and is disabled for use in
the commissioning interface.
6/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Operating mode Switching operation
Push-button operation
Flashing
Continuous on
Continuous off
Basic setting: Switching
operation
Switching operation
After switch-on, the device
remains stable in the "On"
state, and stable in the "Off"
state after switch-off.
Push-button operation
The device switches "On"
when any channel button of a
radio transmitter is pressed
and "Off" when the button is
released. It is irrelevant
whether the "On" or "Off"
channel button is pressed.
Flashing
Switch-on starts flashing and
switch-off stops flashing. The
default flash frequency is 1
Hz. This frequency is also the
maximum flash frequency.
The flash frequency can be
changed using parameters.
The parameter "Switch-off
delay" is used for the pulse
time and the parameter
"Switch-on delay" for the
pause time.
Continuous on
The output switches to
continuously "On". All
operations of radio
transmitters and the Prog
button are ignored.
Continuous off
The output switches to
continuously "Off". All
operations of radio
transmitters and the Prog
button are ignored.
Advanced device settings
Parameters Setting options, Basic
setting
Explanations
Manual commissioning On, Off
Basic setting: On
Disables manual
commissioning for all device
channels. In the "Off" setting,
the device cannot be reset to
the factory setting.
Channel settings
Parameters Setting options, Basic
setting
Explanations
7/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Switch-on delay 0 s … 24 h
Basic setting: 0 s
The load switches on after a
delay. Repeated switch-on
commands restart the delay
time. If the load has not yet
been switched on due to the
delay when a switch-off
command comes, then the
load will remain off.
In Flashing operating mode,
the pause time is set using
this parameter.
Comment: The set times apply
to operation using radio
transmitters. The relay is
switched immediately when
the Prog button is pressed.
Switch-off delay 0 s … 24 h
Basic setting: 0 s
The load switches off after a
delay. Repeated switch-off
commands restart the delay
time. If the load has not yet
been switched off due to the
delay when a switch-on
command comes, then the
load will remain on.
In Flashing operating mode,
the pulse times are set using
this parameter.
Comment: The set times apply
to operation using radio
transmitters. The relay is
switched immediately when
the Prog button is pressed.
Run-on time 0 s … 24 h
Basic setting: 0 s
As soon as a run-on time has
been entered, the actuator will
no longer remain on
permanently, but only for the
length of the run-on time. The
run-on time is restarted if
actuation is repeated. This
parameter is directly
connected to the "Manual
switch-off of run-on time"
parameter.
Comment: The set times apply
to operation using radio
transmitters. The relay is
switched immediately when
the Prog button is pressed.
Manual switch-off of the run-
on time
On, Off
Basic setting: Off
Allows manual switch-off of a
running run-on time. If the
parameter is switched off, then
a switch-off command will also
switch the actuator on. This
parameter is directly
connected to the "Run-on
time" parameter.
8/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Operating hours 0...65535
Basic setting: Current value
The time is counted during
which the load is physically
switched on (relay contact
closed).
This parameter can be reset to
"0", for example after
exchanging the load.
The Reset button is used to
reset the meter to "0". The
device must be programmed
to apply the change.
Extended channel settings
Parameters Setting options, Basic
setting
Explanations
Operating mode Switching operation
Push-button operation
Flashing
Continuous on
Continuous off
Basic setting: Switching
operation
See Device and channels.
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel. In the
"Off" setting, the device
cannot be reset to the factory
setting.
Local Operation On, Off
Basic setting: On
Blocks the output for operation
using the Prog button.
Behaviour on voltage return On
Off
Last value
Configured brightness
Basic setting: Off
Defines the behaviour of the
output after voltage return.
Timer behaviour, voltage
return
Off
Restart
Basic setting: Off
Specifies whether the timers
for switch-on delay, switch-off
delay and run-on time remain
off after voltage return or
whether they restart. Directly
connected to the parameters
"Switch-on delay", "Switch-off
delay" and "Run-on time".
Behaviour after the end of the
disabling function
On
Off
no change
Last value
Basic setting: No change
Behaviour of the output when
a block is removed.
Manual saving of the scene
values
On, Off
Basic setting: On
Disables the saving of the
current actuator state (On/Off)
as scene value in an actuator
for a command via a
transmitter.
9/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Switch-off warning On, Off
Basic setting: Off
If the switch-off warning is
active, the light is not switched
off directly. The light goes off
30, 15 and 6 seconds before
permanent switch-off. During
the switch-off warning, a
switch-on telegram effects
direct switch-on. It is not
possible to terminate the time
using a switch-off telegram.
Priority, lock-out protection 0...4
Basic setting: 1
Specifies the priority for
recalling and removing a
scene of type Lock-out
protection for the channel.
Activate lock-out protection
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on activating the lock-
out protection.
Deactivate lock-out protection
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
lock-out protection. Only
visible when the priority for the
lock-out protection is 0.
Priority, restraint 0...4
Basic setting: 2
Specifies the priority for
recalling and removing a
scene of type Restraint for the
channel.
Activate forced operation
switching state
On, Off
Basic setting: On
Defines the behaviour of the
output on activating the forced
operation.
Deactivate forced operation
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
forced operation. Only visible
when the priority for the forced
operation is 0.
Priority, wind alarm 0...4
Basic setting: 3
Specifies the priority for
recalling and removing a
scene of type Wind alarm for
the channel.
Activate wind alarm switching
state
On, Off
Basic setting: Off
Defines the behaviour of the
output on activating the wind
alarm.
Deactivate wind alarm
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.
Priority, sun protection 0...4
Basic setting: 0
Specifies the priority for
recalling and removing a
scene of type Sun protection
for the channel.
Activate sun protection
switching state
On, Off
Basic setting: On
Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun
protection is 0.
10/12
82581723
J0082581723 23.03.2017
eNet radio switch/push-button actuator 1-gang, for rail mounting
Table of contents
Other Jung Controllers manuals
Jung
Jung HOME BTS1B2U User manual
Jung
Jung 2204 REG User manual
Jung
Jung FST 1240 EB User manual
Jung
Jung 2204 REG User manual
Jung
Jung KNX 2131.16 UP User manual
Jung
Jung RCD 20 series User manual
Jung
Jung Smart Control SC 1000 KNX Operator's manual
Jung
Jung KNX 360061SR User manual
Jung
Jung 390041SR User manual
Jung
Jung eNet FMAS10UP User manual
Jung
Jung FA 26 UP User manual
Jung
Jung KNX 2136 REG HZ User manual
Jung
Jung LS TOUCH User manual
Jung
Jung 3210 UP User manual
Jung
Jung KNX 390011 SU User manual
Jung
Jung 2501 HZUP User manual
Jung
Jung 4093 KRM TS D Operator's manual
Jung
Jung 2424 REG HE User manual
Jung
Jung PUMA User manual
Jung
Jung LB management User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
