Johnson Controls TEC3310 User manual

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone

Thermostat Controllers with Dehumidification Capability

Installation Instructions

Refer to the QuickLIT website for the most up-to-date version of this document.

Applications

The TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers are stand-alone and

field-selectable BACnet® MS/TP or N2 networked devices that provide control of the following:

• local hydronic reheat valves

• pressure-dependent variable air volume (VAV) equipment with or without local reheat

• two- or four-pipe fan coils

• cabinet unit heaters

• other individual zone equipment using an on/off or floating control input

The networked models feature a field-selectable Building Automation System (BAS) BACnet MS/TP or N2

communication capability that enables remote monitoring and programming for efficient space temperature control.

All models include a USB port configuration that reduces installation time by allowing simple backup and restore

features from a USB drive, which enables rapid cloning of configuration between like units.

Some models have occupancy sensing capability built into the device. These thermostat controllers maximize up to

30% energy savings in high-energy usage commercial buildings, such as schools and hotels, during occupied

times by using additional standby setpoints.

All models feature an intuitive onboard touchscreen UI with backlit display that makes setup and operation quick

and easy. Multiple fan configurations are supported for fan coil equipment types:

• single-speed

• multi-speed (two or three discrete speeds)

• variable-speed/EC motors (0 to 10 VDC control)

Some models support dehumidification on two-pipe fan coil units with reheat, and four-pipe fan coil units with or

without reheat. When no heating is required, the thermostat controller monitors space humidity and activates

dehumidification control as necessary. Heat and/or reheat is used as required to maintain the space temperature.

For optimal dehumidification performance, use a fan coil unit that has a multi-speed or variable-speed fan (VSF).

TEC3000 Series On/Off or Floating Fan Coil and Individual

Zone Thermostat Controllers with Dehumidification

Capability

Installation Instructions

TEC3310-xx-xxx, TEC3311-xx-xxx, TEC3312-xx-xxx, TEC3313-xx-xxx,TEC3610-xx-xxx, TEC3611-xx-xxx, TEC3612-xx-xxx, TEC3613-xx-xxx

Part No. 24-10787-6, Rev.

Issued July 2018

(barcode for factory use only)

24-10787-6, Rev. F

*24107876F*

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

North American Emissions Compliance

United States

Canada

Installation

Parts Included

• one TEC3000 Series Thermostat Controller with integral mounting base

• one installation instructions sheet

IMPORTANT: The TEC3000 Series Thermostat Controller is intended to provide an input to equipment under

normal operating conditions. Where failure or malfunction of the thermostat controller could lead to personal

injury or property damage to the controlled equipment or other property, additional precautions must be

designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems

or safety or limit controls, intended to warn of or protect against failure or malfunction of the thermostat

controller.

IMPORTANT : Le TEC3000 Series Thermostat Controller est destiné à transmettre des données entrantes à un

équipement dans des conditions normales de fonctionnement. Lorsqu'une défaillance ou un dysfonctionnement

du thermostat controller risque de provoquer des blessures ou d'endommager l'équipement contrôlé ou un autre

équipement, la conception du système de contrôle doit intégrer des dispositifs de protection supplémentaires.

Veiller dans ce cas à intégrer de façon permanente d'autres dispositifs, tels que des systèmes de supervision ou

d'alarme, ou des dispositifs de sécurité ou de limitation, ayant une fonction d'avertissement ou de protection en

cas de défaillance ou de dysfonctionnement du thermostat controller.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This Class (B) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la Classe (B) respecte toutes les exigences du Règlement sur le matériel brouilleur

du Canada.

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Location Considerations

Locate the TEC3000 Series Thermostat Controller:

• on a partitioning wall, approximately 5 ft (1.5 m)

above the floor in a location of average

temperature, allowing for vertical air circulation to

the TEC

• away from direct sunlight, radiant heat, outside

walls, outside doors, air discharge grills,

stairwells, and from behind doors

• away from steam or water pipes, warm air stacks,

unconditioned areas (not heated or cooled), or

sources of electrical interference

For integrated passive infrared (PIR) models, be sure

that the thermostat controller is located centrally,

where occupant movement is frequent.

Use insulating foam pads for installations where

wiring passes through the wall to the thermostat.

Note: Allow for sufficient clearance to insert a USB

drive into the USB port.

Installing the Thermostat Controller

1. Use a 1/16 in. (1.5 mm)Allen wrench or Johnson Controls® T-4000-119 Allen-HeadAdjustment Tool (order

separately) to remove the security screw if it is installed on the top of the thermostat controller cover as

illustrated in Figure 2.

2. Pull the top edge of the cover and open the thermostat controller as illustrated in Figure 2.

IMPORTANT: Only connect memory devices to the USB port. Do not use it for charging external devices.

IMPORTANT: The cover is not secured on the bottom. Be careful not to drop the cover.

IMPORTANT: If you are installing more than one thermostat controller, keep track of which cover attaches to

which base.

IMPORTANT: Use proper Electrostatic Discharge (ESD) precautions during installation and servicing to avoid

damage to the electronic circuits of the thermostat controller.

Figure 1: Thermostat Controller

Shown without Occupancy Sensor,

Dimensions, in. (mm)

FIG:thermostat features

USB Port

Display

Security Screw

1-13/32

(36)

4-23/32

(120)

5-5/8

(143)

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Figure 2: Removing the Security Screw from the Thermostat Controller Cover

(Shown without Occupancy Sensor) (Left) and Removing the Thermostat Controller Cover (Right)

3. Align the thermostat controller mounting base on the wall with the security screw on the top and use the base

as a template to mark the two mounting hole locations. See Figure 3.

Notes:

• If you need to install the thermostat controller on an electrical junction box, use

2-1/2 x 4 in. (63 x 101 mm) square boxes with mud ring covers and avoid smaller 1-1/2 x 4 in.

(38 x 101 mm) square or 3 x 2 in. (76 x 51 mm) boxes. This procedure ensures that you have enough

space for cabling, if needed.

• For surface-mounted applications, use durable mounting hardware, such as wall anchors, that cannot be

easily pulled out of the mounting surface.

4. Pull approximately 6 in. (152 mm) of wire from the wall and insert the wire through the center hole in the

thermostat controller mounting base. See Figure 3.

5. Secure the mounting base to the wall surface using two mounting screws (user supplied) as illustrated in

Figure 3.

Note: Be careful not to overtighten the mounting screws.

FIG:securit y screw

FIG:thermostat cover

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Figure 3: Mounting Hole Locations, Dimensions, in. (mm) (Left) and

Securing the Thermostat Controller Mounting Base to the Wall (Right)

Wiring

Whenanexistingthermostatcontrollerisreplaced,removeandlabelthewirestoidentifytheterminalfunctions.

Risk of Electric Shock.

Disconnect the power supply before making electrical connections to avoid electric shock.

Risque de décharge électrique.

Débrancher l'alimentation avant de réaliser tout raccordement électrique afin d'éviter tout risque de décharge

électrique.

Risk of Property Damage.

Do not apply power to the system before checking all wiring connections. Short circuited or improperly connected

wires may result in permanent damage to the equipment.

Risque de dégâts matériels.

Ne pas mettre le système sous tension avant d'avoir vérifié tous les raccords de câblage. Des fils formant un

court-circuit ou connectés de façon incorrecte risquent d'endommager irrémédiablement l'équipement.

IMPORTANT: Make all wiring connections in accordance with local, national, and regional regulations. Do not

exceed the electrical ratings of the TEC3000 Series Thermostat Controller.

4-1/16

(103)

FIG:TEC Backplane2

3-1/4

(83)

FIG:TEC Backplane1

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

To wire the thermostat controller:

1. Strip the ends of each wire 1/4 in. (6 mm) and connect them to the appropriate screw terminals as indicated in

Table 2 and Figure 6 or Figure 7.

Note: For more details on wiring the MS/TP Communications Bus, refer to the MS/TP Communications Bus

Technical Bulletin (LIT-12011034).

2. Carefully push any excess wire back into the wall.

Note: Seal the hole in the wall with fireproof material to prevent drafts from affecting the ambient temperature

readings.

3. Reattach the communication wires to the terminal block.

Note: If multiple wires are inserted into the terminals, be sure to properly twist the wires together before

inserting them into the terminal connectors.

4. Set the bus end-of-line (EOL) termination switch to the desired location on the TEC3610-00-000,

TEC3611-00-000, TEC3612-00-000, and TEC3613-00-000 models only.

The bus EOL termination switch allows you to designate the thermostat controller as the end of the Field

Controller (FC) Bus and N2 Bus. The default position is OFF. If the thermostat controller is at the end of a daisy

chain of devices on the FC Bus and N2 Bus, set the EOL switch to the ON position. See Figure 4.

Figure 4: EOL Switch Position (Left) and Installing the Thermostat Controller Cover (Right)

5. Reattach the thermostat controller cover to the mounting base (bottom side first).

IMPORTANT: Use proper ESD precautions during installation and servicing to avoid damage to the electronic

circuits of the thermostat controller.

IMPORTANT: Make sure you reattach the cover that corresponds to its correct base. The CPU board number

needs to match the base board number. Otherwise, an operation error occurs after you reattach a cover and

base that do not belong together (as shown in Figure 5). See Table 1 on page 7 for TEC3000 model names and

code numbers.

FIG:EOL_Swtch

EOL Switch

ON Position

EOL Switch

OFF Position

FIG:TEC Backplane2_EOL Switch

FIG:close thermostat cover

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

6. Use a 1/16 in. (1.5 mm)Allen wrench or Johnson Controls T-4000-119 Allen-Head Adjustment Tool (order

separately) to reinstall the security screw on the top of the thermostat controller cover. See Figure 2 for security

screw placement.

7. Remove the protective plastic cover sheet from the display.

Table 1: TEC3000 Model Names and Code Numbers

Name Code Number1

1. The two-character code number is listed within the error code to

indicate that the CPU board and base board do not belong together.

However, if the same code number appears as both the CPU board

and base board, there is no error. For example, if 0B is listed as the

CPU board and the base board, the model is the TEC3611.

Name Code Number1

TEC3310 00 TEC3610 0A

TEC3311 01 TEC3611 0B

TEC3312 02 TEC3612 0C

TEC3313 03 TEC3613 0D

TEC3320 04 TEC3620 0E

TEC3321 05 TEC3621 0F

TEC3322 06 TEC3622 10

TEC3323 07 TEC3623 11

TEC3330 08 TEC3630 12

TEC3331 09 TEC3631 13

IMPORTANT: If the display is dirty, gently wipe it clean with isopropyl alcohol or ethyl alcohol. Do not scrub

hard as to avoid damaging the surface. Do not use other cleaners such as water, ketones, and aromatic

solvents, since they may damage the polarizer.

CPU Board Base Board

Figure 5: Error Code Indicating

Mismatched Boards

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Table 2: Terminal Identification (See Figure 6 and Figure 7 for Wiring Diagrams)

Terminal Label Function

TEC3310, TEC3311, TEC3312, TEC3313

Floating FC/VAV and On/Off FC1TEC3610, TEC3611, TEC3612, TEC3613

Floating FC/VAV and On/Off FC1

24 V 24 VAC hot from transformer

FAN H Fan high

FAN M Fan medium

FAN L Fan on (single-speed, variable speed), Fan low (multi-speed)

AUX Auxiliary binary output

AUX Auxiliary power

COM224 VAC common from transformer

CLG O Cool open (Floating), Cooling NC (On/Off), Triac

CLG C Cool close (Floating), Cooling NO (On/Off), Triac

HTG O Heat open (Floating), Heating NC (On/Off), Triac

HTG C Heat close (Floating), Heating NO (On/Off), Triac

COM2Common

VSF Variable speed fan command (configurable 0 to 10 V range)

BI2 Configurable binary input 2

BI1 Configurable binary input 1

COS Changeover sensor

R SEN Remote zone temperature sensor

NET+ Not connected Field bus+/N2+

NET- Not connected Field bus-/N2-

NET COM Not connected Isolated common for field bus

1. There is no support for an On and Off VAV.

2. The common terminals, which do not include NET COM, are internally connected and can be used for all inputs and

outputs.

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Notes:

• VAV and 2-pipe systems should connect their valve to the heating output.

• Only one transformer is required for each TEC.

Figure 6: On/Off Wiring Diagram (See Table 2 for Terminal Identification)

Zone Temp

Thermistor

Supply Temp

Switch

FIG:Model 1 Wiring_on_off_output

24 V

R SEN

24V

NET COM

COS

VSF

COM

Supply Temp

Thermistor

Vin

Common

24 V

High

Med

FAN H

AUX

TB1

CLG C

Low

Fan

Common

Hot

Heating

Common

Hot

FAN M

FAN L

AUX

FIG:Model 1 Wiring_on_off_input

N.C.

Common

Hot

Common

Hot

N.O.

TEC3000 Series On/Off or Floating Fan Coil and Individual Zone Thermostat Controllers with Dehumidification

Capability Installation Instructions

Notes:

• For VAV and 2-pipe systems, connect the valve to the heating output.

• Only one transformer is required for each TEC.

Figure 7: Floating Wiring Diagram (See Table 2 for Terminal Identification)

FIG:Model 1 Wiring_floating_output

Zone Temp

Thermistor

SupplyTemp

Switch

24 V

Vin

Common

R SEN

24V

NET COM

COS

VSF

COM

SupplyTemp

Thermistor

EC Motor

24 V

High

Med

FAN H

AUX

TB1

CLG C

Low

Fan

Heating

FAN M

FAN L

AUX

FIG:Model 1 Wiring_floating_input

Open

Hot

Open

Hot

This manual suits for next models

Table of contents

Other Johnson Controls Controllers manuals

Johnson Controls

Johnson Controls Tyco Kantech KT-400 Quick start guide

Johnson Controls

Johnson Controls G76 Series User manual

Johnson Controls

Johnson Controls LX Series User manual

Johnson Controls

Johnson Controls T-5800 Series Use and care manual

Johnson Controls

Johnson Controls M9108-A-1N Series User manual

Johnson Controls

Johnson Controls M9106 Series User manual

Johnson Controls

Johnson Controls M9220-GG-3 Series User manual

Johnson Controls

Johnson Controls FX Supervisory Controller RS-485 Card User manual

Johnson Controls

Johnson Controls A25 Series Service manual

Johnson Controls

Johnson Controls TEC2664Z-3 BACnet User manual

Johnson Controls

Johnson Controls FX-PCA2611-0 User manual

Johnson Controls

Johnson Controls VG1600 Series User manual

Johnson Controls

Johnson Controls FX-PCG1621 Series User manual

Johnson Controls

Johnson Controls LC-AVMHTC1-0 User manual

Johnson Controls

Johnson Controls M9132-AG -1N Series User manual

Johnson Controls

Johnson Controls M9316-A Z Series User manual

Johnson Controls

Johnson Controls FX30E Service manual

Johnson Controls

Johnson Controls FAC2612-2 User manual

Johnson Controls

Johnson Controls EDA-8102 User manual

Johnson Controls

Johnson Controls G961DAJ User manual

Johnson Controls

Johnson Controls TEC3000 Series User manual

Johnson Controls

Johnson Controls EasyIO FW-08 V3 User manual

Johnson Controls

Johnson Controls M9102-AGA-2S Series User manual

Johnson Controls

Johnson Controls G670 Assembly instructions

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual