Johnson Controls S321-IP Manual
24-10239-480 Revision F
December 2017
hardware installation
S321-IP
Network Controller
Copyright 2017
Johnson Controls
All Rights Reserved
No part of this document may be reproduced without the prior permission of Johnson Controls.
If this document is translated from the original English version by Johnson Controls, all reasonable
endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable
for any translation errors contained herein or for incidental or consequential damages in connection
with the furnishing or use of this translated material.
Due to continuous development of our products, the information in this document is subject to
change without notice. Johnson Controls shall not be liable for errors contained herein or for
incidental or consequential damages in connection with furnishing or use of this material. Contents
of this publication may be preliminary and/or may be changed at any time without any obligation to
notify anyone of such revision or change, and shall not be regarded as a warranty.
Other Manufacturers’ Documentation
Johnson Controls does not duplicate documentation of other equipment manufacturers. When
necessary, Johnson Controls provides documentation that supplements that of other manufacturers.
When unpacking your equipment, keep all original manufacturer documentation for future
reference.
Technical Support
For factory technical support, Johnson Controls authorized field technicians or authorized dealer
representatives can contact Global Security Solutions Technical Support by phone at
can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.
End users and customers should contact their local Johnson Controls branch or authorized dealer
for any of their support needs (technical support, maintenance contracts, on-site field support,
P2000 Software Service Agreements, Service Partnerships, and so on). Visit
http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.
For material returns contact the branch if the material was purchased through a Johnson Controls
branch or through the Product Sales Operations Team, if ordered through the Advanced Order
Management System (AOMS) and follow the RMA process; or contact the authorized dealer
representative where the material was purchased directly.
Acknowledgment
Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and
product names are trademarks or registered trademarks of their respective owners.
Declarations of Conformity
United States: This equipment, S321-IP, has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Canada: CAN ICES-3 (A)/NMB-3(A)
European Union: This product complies with the requirements of the EMC Directive.
This equipment must not be modified for any reason and it must be installed as stated in the
Manufacturer’s instructions. If this shipment (or any part thereof) is supplied as second-hand
equipment, equipment for sale outside the European Economic Area or as spare parts for either a
single unit or system, it is not covered by the Directives.
UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET
The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary
Burglar Alarm Units and Systems and UL 294 for Access Control Systems Units and Underwriters
Laboratories of Canada ULC/ORD-C1076-86.
S321-IP
When installed at the site the following requirements must be met to comply with these standards.
1. The S321-IP shall be mounted in subassembly S300-DIN-L or S300-DIN-S.
2. The tamper switch must be enabled at all times.
3. Transient protection devices that are installed must not be removed or defeated.
4. Do not connect equipment to an AC power source that is controlled by a switch.
5. The sole use of a class 2 transformer to power the S321-IP would not provide battery
standby power.
6. The RS485 reader interfaces were not investigated by Underwriters Laboratories.
7. For a UL 294 Listed system the following Listed readers may be used.
8. Model S321-IP must use a Class 2 direct plug-in transformer rated 120 VAC input and
24 VAC, 50 VA output from one of the following manufacturers:
Basler, part number BE116450CAA or BE116450AAA
Potter Electric Signal Co. (Amseco), model XR-2450LED
Revere Industries, model RT-2450SL/M
9. UL 294 Performance Levels
Destructive Attack Level I
Endurance Level IV
Line Security Level II
Standby Power Level I
Manufacturer Models
HID Corp. 30387, 31503, 31815, 31880, 32005, 32788, 32985
5355, 5365, 5395, 5405, 5455, 6005
All models may be followed by additional suffixes
Mercury Security Corp. MR-5
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
1
S321-IP HARDWARE INSTALLATION
The S321-IP controller communicates with the host via Ethernet. It supports up
to two doors per unit and allows you to configure supervised 4-state inputs and
unsupervised 2-state inputs. The S321-IP controller provides power for the card
reader hardware; it does not provide power for the door locking hardware.
ABOUT THIS DOCUMENT
This document describes S321-IP hardware installation, basic operation, and
maintenance procedures. It is divided into the following sections:
•Unpacking the Equipment on page 1
•Tools Needed on page 1
•Mounting on page 2
•Description of Signals on page 5
•Cable Requirements on page 7
•Basic Commissioning on page 10
•The S321-IP User Interface on page 16
•Technical Specifications on page 19
•Maintenance on page 20
UNPACKING THE EQUIPMENT
Inspect the S321-IP shipping containers as soon as you receive them, with the
delivery agent present. If a container is damaged, open it immediately, inspect
the contents, and have the agent make note on the shipping document. Check
the purchase order against the packing slips to ensure the order is complete. If
the contents of a container are damaged, notify the carrier and your
Johnson Controls representative immediately. Report any discrepancies to your
Johnson Controls representative. Save the packing materials for possible return
shipments.
Your package should contain the S321-IP controller, connectors set, a CD
containing a set of user documentation, and this manual.
TOOLS NEEDED
Use a small, straight-blade screwdriver to secure wires in the terminal blocks.
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
2
MOUNTING
You can mount the S321-IP controller on a flat surface, DIN rail, or in a
Johnson Controls’ approved enclosure (for example: S300-DIN).
For information on mounting the S321-IP in an enclosure, refer to the manual
provided with the enclosure.
To mount an S321-IP controller on a flat surface:
1. Fully extend the white clips located on the top and bottom of the
controller. You may need to remove the connectors.
2. Mount the controller to the surface with mounting screws.
3. Replace the connectors, if previously removed.
To mount an S321-IP controller on a DIN rail:
1. Fully extend the white clips located on the bottom of the controller.
You may need to remove the connectors.
2. Hook the controller on top of the rail and push in the clips.
Fully extended clips for
wall mount
(connectors are removed)
S321-IP
DIN rail
S321-IP
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
3
3. If you need to remove a controller from the DIN rail, reverse the
mounting sequence (pull down the bottom clips, then pull the bottom
of the controller out and lift it up.)
Power Source Requirements
Line Voltage Information
If the facility is located in an area where power lines are subject to
frequent lightning strikes, verify with the electric company that the
building transformer is equipped with surge protectors. These, as well as
a “crowbar” type of protection, can be installed at the main service
entrance if the building transformer is not equipped with lightning
protection.
While lightning is one cause of power line transients, others can be
internal or external to the building environment. The general application
of transient surge suppression is low-cost insurance to ensure long life of
the equipment being installed.
Lithium Battery
The S321-IP contains a lithium battery that is used for realtime clock
backup. The lithium battery is shipped from the factory charged and
operational.
If there are no power outages, change the battery every five years. If a
power outage occurs, the battery life is approximately 30 days. Replace
with Panasonic part number CR2025 or equivalent.
Parameter Value
Power 24 W
Input voltage +12 to +28 VDC; 16 to 28 VAC
Nominal voltage +12 to +24 VDC; 16 to 24 VAC
Current 1 A at 24 V; 2 A at 12 V
Class 2 transformer (optional) See step 8 on the Underwriters Laboratories Compliance
Verification Sheet at the beginning of this manual.
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
4
IMPORTANT: After you replace the lithium battery (recommended every five
years or after extended use), verify that the realtime clock is correct; otherwise,
you may need to adjust the time.
To replace the lithium battery:
1. Disconnect the 24 VDC power from the S321-IP.
2. Unscrew and open the plastic enclosure.
3. With a narrow (1/8 in.) blade, carefully pry up the battery until a
portion of the battery is out of the plastic holder.
4. With your free hand gently move the battery out of the holder while
keeping the battery pried up.
5. Dispose of the old battery according to local requirements.
6. Insert the new battery into holder.
IMPORTANT: The lithium battery is polarized. Ensure the side marked ‘+’ faces
out (that is, towards you).
7. Close the plastic enclosure and secure it with the screw.
8. Re-connect the power to the S321-IP.
CAUTION: Risk of Explosion.
Replace the battery with a lithium battery of the same type and
voltage rating. Dispose of the used battery in accordance with local,
national, and regional regulations. Failure to replace the battery with
one of the same type and voltage rating may result in an explosion
causing personal injury and property damage.
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
5
DESCRIPTION OF SIGNALS
READER n
COM
NC
NO
COM
NC
TAMP
COM
SPARE
PWR FAIL
COM
TAMP
NO
RDR n
STRIKE
RDR n
SHUNT
POWER RETURN
CAL RESISTOR
CAL RESISTOR
DATA1/Rs485+
DATA0/Rs485-
COM
POWER
GREEN LED
COM
RED LED
REX
COM
DOOR CONTACT
+12/24 VAC/VDC
RDR n PANEL
RDR n RDR n RDR n CAL POWER
RDR Request to
Exit Device
RDR Red Light
RDR Green Light
RDR Door
Reader
Calibration
Resistor
To the power
supply
RDR Door
Contact
RDR 1 General
Purpose Input 5
RDR 1 General
Purpose Input 6
RDR General
Purpose Input 3
RDR General
Purpose Input 4
RDR Shunt
RDR Strike
READER
1
RJ45
connector
READER
2
S321-IP Network Controller Hardware Installation
24-10239-480 Rev. F
6
Wiegand Input
Description of Signals – DATA0 and DATA1 from each reader,
complying with the Wiegand interface specification.
Reference – These signals are referenced to logic ground (COM).
Protection – Each signal has a 6 V transient voltage suppressor between
it and COM.
Input Points
Description of Signals – The following are internally pulled up inputs:
The allowable voltage range for these signals is 0-12 VDC.
Reference – These signals are referenced to their associated COM input.
Protection – Each signal is protected with series resistors and dual
clamping diodes.
External Circuits – 4-state operation requires two external resistors and
switch circuit connected between an input point and COM. 2-state
operation requires an external switch connected between an input point
and COM. For wiring details see Wiring Input Devices on page 8.
Output Points
Description of Signals – The following are open collector outputs, with
voltage range for these signals of 0-24 VDC, limited to 50mA:
IMPORTANT: These open collector outputs can be damaged by alternating
current (AC) potentials as low as 1 VAC. Connect the LED outputs only to direct
current (DC) loads up to 24VDC.
• Reader 1 Door
Contact
• Reader 1 REX
•Reader 1 Tamper
• Reader 1 Spare
• Reader 2 Door
Contact
• Reader 2 REX
•Reader 2 Tamper
• Reader 2 Spare
• Power Panel Fail
• Panel Tamper
• Reader 1 Red LED
• Reader 1 Green LED
• Reader 2 Red LED
• Reader 2 Green LED
Table of contents
Other Johnson Controls Controllers manuals
Johnson Controls
Johnson Controls M9320-AUA-4 User manual
Johnson Controls
Johnson Controls LN Series User manual
Johnson Controls
Johnson Controls VA-7700 Series User manual
Johnson Controls
Johnson Controls VA9204-B-2 Series User manual
Johnson Controls
Johnson Controls FEC26 Series User manual
Johnson Controls
Johnson Controls NAE35 User manual
Johnson Controls
Johnson Controls VA-747 Series User manual
Johnson Controls
Johnson Controls LN Series User manual
Johnson Controls
Johnson Controls LN Series User manual
Johnson Controls
Johnson Controls FMS-1655 Series User manual
Johnson Controls
Johnson Controls RA-3 Series Owner's manual
Johnson Controls
Johnson Controls PENN ACT2 Service manual
Johnson Controls
Johnson Controls M9310 Series User manual
Johnson Controls
Johnson Controls VA-9070 Series Service manual
Johnson Controls
Johnson Controls M9102-GA-1S Series User manual
Johnson Controls
Johnson Controls York 366-70488 Instruction Manual
Johnson Controls
Johnson Controls FX-PCV18 Series User manual
Johnson Controls
Johnson Controls M9108 Series User manual
Johnson Controls
Johnson Controls HS3032 User manual
Johnson Controls
Johnson Controls VMA1617 User manual
Popular Controllers manuals by other brands
Digiplex
Digiplex DGP-848 Programming guide
YASKAWA
YASKAWA SGM series user manual
Sinope
Sinope Calypso RM3500ZB installation guide
Isimet
Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions
LSIS
LSIS sv-ip5a user manual
Rockwell Automation
Rockwell Automation 1769-L31 installation instructions
