Johnson Controls A19ZBA User manual

FANs 121, 125

Temperature Controls Section A

Technical Bulletin A19ZBA

Issue Date 1291

Code No. LIT-121065

Part No. 997-778

A19ZBA Type Temperature Control

Application

The A19ZBA temperature control

is designed for water chiller

applications. The control has a

range of 38 to 80°F (3 to 27°C)

with contacts that open on a

temperature drop.

A packing nut assembly, Part

No. FTG13A-600R, (Fig. 2) is

supplied with the control for

immersion applications where a

bulb well is not required. Bulb

well No. WEL14A-600R (Fig. 3)

for immersion applications is

available, if required.

All Series A19 controls are

designed for use only as

operating controls. Where an

operating control failure

would result in personal injury

and/or loss of property, it is

the responsibility of the

installer to add devices

(safety, limit controls) or

systems (alarm, supervisory

systems) that protect against,

or warn of, control failure.

Installation

When provided, follow the

equipment manufacturer’s

instructions. If instructions are

not supplied, follow the

instructions in this sheet.

CAUTION: Do not dent or

deform the sensitive bulb of

this control. A dent or

deformation will change the

calibration and cause the

control to cycle at a

temperature lower than the

dial setting.

Mounting

When installing the control, use

the mounting bracket as a

template and mark the location

for the two mounting screws.

Drill or punch two holes and start

the mounting screws. Place the

slot in the bottom of the bracket

under the head of the lower

mounting screw. Position the

control so the top screw is in the

top slot. Tighten both screws. It

is not necessary to level the

control except for appearance.

For closed tank applications

without a bulb well, use the

FTG13A-600R packing nut. (See

Fig. 2.) Put parts over the support

tube section of the element and

place bulb in the tank. Install the

1/2 in. NPT adapter in the tank

opening and tighten. Screw the

packing nut with the retaining

washers and packing into the

adapter as shown in Fig. 2.

CAUTION: Turn off the

liquid supply and relieve the

pressure before installing or

removing the bulb or bulb

well.

For applications requiring a bulb

well, install the bulb well in the tank

opening. Remove the bushing

from the bulb well and slide the

bushing over the capillary. Insert

the bulb into the bulb well and

replace the bushing. Push the

bulb into position in the bottom of

the well. Tighten the set screw in

the adapter end to hold the bulb in

position.

Wiring

WARNING: Disconnect the

power supply before wiring

connections are made to

avoid possible electrical

shock or damage to the

equipment.

Make all wiring connections

using copper conductors only,

and in accordance with the

National Electrical Code and

local regulations.

Fig. 1 -- A19ZBA-1 Temperature

Control. Note the mounting

bracket on the back of the case.

Note: Use the terminal screws

furnished (8-32 ×1/4 in. binder

head). Substitution of other

screws may cause problems in

making proper connections.

2 A19ZBA Technical Bulletin

Adjustments (See Fig. 4)

The A19ZBA control has a

locked low cutout stop. Pointer

"B" is locked in place with a

screw that requires a special

spanner wrench, Part No.

836-61, to change the setting.

The special wrench is supplied

with each control. To change

the low cutout stop setting,

proceed as follows:

1. Loosen screw "C" with the

special wrench.

2. Slide pointer arm "B" to the

desired cutout setting

(adjustable from

approximately 38 to 48°F

[3 to 9°C]). The cutout

setting is indicated by the

flat of arm "B."

3. Tighten screw "C."

The cut-in temperature is set by

moving knob "A" to the desired

cut-in setting. This knob

adjustment does not change the

cutout setting, but provides for a

short or long recycle time as

required by the application.

Checkout Procedure

Before leaving the installation,

observe at least three complete

operating cycles to be sure that

all components are functioning

correctly.

Repairs and Replacement

Field repairs must not be made.

For a replacement control,

contact the nearest Johnson

Controls distributor.

Controls Group

507 E. Michigan Street

P.O. Box 423 Printed in U.S.A.

Milwaukee, WI 53202

Other Johnson Controls Controllers manuals

Johnson Controls

Johnson Controls penn TC3B21 User manual

Johnson Controls

Johnson Controls MR12DR230-1C User manual

Johnson Controls

Johnson Controls York YKN2Open board Manual

Johnson Controls

Johnson Controls VG1600 Series User manual

Johnson Controls

Johnson Controls FX70 User manual

Johnson Controls

Johnson Controls Penn P216 Series User manual

Johnson Controls

Johnson Controls Tyco KT-1 User manual

Johnson Controls

Johnson Controls EasyIO FW-28 User manual

Johnson Controls

Johnson Controls FAC3613 User manual

Johnson Controls

Johnson Controls Penn P216 User manual

Johnson Controls

Johnson Controls Facility Explorer FX40 User manual

Johnson Controls

Johnson Controls VA-747 Series User manual

Johnson Controls

Johnson Controls TEC2664Z-3 BACnet User manual

Johnson Controls

Johnson Controls tyco Power Neo HS2016 User manual

Johnson Controls

Johnson Controls FAC3611 User manual

Johnson Controls

Johnson Controls Metasys DX-9100 Service manual

Johnson Controls

Johnson Controls T9800 Series Service manual

Johnson Controls

Johnson Controls VA9104-AGA-1S User manual

Johnson Controls

Johnson Controls P266 Series User manual

Johnson Controls

Johnson Controls P2000 Manual

Johnson Controls

Johnson Controls VA-8052 User manual

Johnson Controls

Johnson Controls VMA1615 User manual

Johnson Controls

Johnson Controls TRUE RH HC-67x3 User manual

Johnson Controls

Johnson Controls TEC3010 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual