Javad TRIUMPH-1 Quick guide
All contents in this manual are copyrighted by JAVAD GNSS.
All rights reserved.The information contained herein may not be used, accessed, copied,
stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express
written consent from JAVAD GNSS.
Base and Rover Setup
via Tracy
Configuration Example
Version 1.0
Last Revised December 14, 2010
www.javad.com
3www.javad.com
BASE AND ROVER SETUP VIA
TRACY
Base Configuration (TRIUMPH-1 with external UHF
Modem)
Establishing Connection between receiver and Tracy
1. Configure your external UHF radio (HPT435) as base using ModemVU software. See
detailed description in “HPT435 as Base TRIUMPH-1 as Rover” Application Notes,
available on the www.javad.com.
2. Connect the TRIUMPH-1 receiver to computer. See for details the TRIUMPH-1
Operator’s Manual.
3. Connect the external HPT435 UHF radio to receiver’s port B with cable Accessory Data-
Ser cable, ODU-7/D15 (1.8 m) p/n 14-578108-01.
Figure 1-1. Accessory Data-Ser cable, ODU-7/D15
Note: The port B is optional. Make sure you have such option purchased.
Base and Rover Setup via Tracy
Base Configuration (TRIUMPH-1 with external UHF Modem)
Establishing Connection between receiver and Tracy
4www.javad.com
4. Power the HPT435. You can use the Battery kit 2 (p/n 99-587100-10).
Figure 1-2. Powering HPT435
5. Turn on the TRIUMPH-1 receiver
6. Start Tracy RTK in the Lite view.
7. Connect you TRIUMPH-1 and controller using Bluetooth.
• If you have once connected the receiver with Victor, Tracy will find it automatically;
• Otherwise click to the connection button to search bluetooth receiver.
Figure 1-3. Connection to the receiver
Base and Rover Setup via Tracy
Base Configuration (TRIUMPH-1 with external UHF Modem)
Base Station Setup
5www.javad.com
Base Station Setup
1. Click Survey parameters button .
2. Click Start Base tab (Figure 1-4). This tab allows the user to apply receiver as the base,
selecting receiver style from the list (how to create new style see “How to create new/edit
receiver style” on page 8), and make settings for base receiver:
Figure 1-4. Start Base tab
If the Write to receiver file check box is selected the logfile will be saved in the receiver’s
memory. Type in the logfile name in the edit field below.
3. Click Start button and enter the base station coordinates:
Figure 1-5. Control point coordinates setup
4. Click Start Base button to start transmit corrections.
5. Click Exit to disconnect and close Tracy.
Base and Rover Setup via Tracy
Rover setup (TRIUMPH-1 with Internal Radio)
Base Station Setup
6www.javad.com
Rover setup (TRIUMPH-1 with Internal Radio)
1. Turn on your receiver which will be configured as rover.
2. Start Tracy RTK in the Lite view. How to switch between Lite and Extended view see on
page 8.
3. Connect you TRIUMPH-1 and controller using Bluetooth.
• If you have once connected the receiver with Victor, Tracy will find it automatically;
• Otherwise click to the connection button to search bluetooth receiver.
Figure 1-6. Connection to the receiver
4. In the extended view click the Survey parameters button, then Survey tab and select the
style:
Figure 1-7. Survey tab
Note: Please note the style should be the same as base has.
Base and Rover Setup via Tracy
Rover setup (TRIUMPH-1 with Internal Radio)
Base Station Setup
7www.javad.com
5. Click Start button to start survey. In the type drop-down list box select Point to survey a
point, or Trajectory for trajectory surveying (Figure 1-8)
• Insert point name in the Name field, code and comments in the corresponding fields.
• Insert the antenna height and type of antenna height measurement.
• Click the Point button to start point surveying. New window with the surveying
information appears.
• To finish surveying this point click the Finish button.
•ClickCancel to stop surveying points.
• If the trajectory is selected, make the same settings as described above, and click the
Trajectory button to start trajectory surveying.
• To finish surveying the trajectory click the Finish button.
•ClickCancel to stop surveying trajectory.
Figure 1-8. Survey Tab. Point surveying
Base and Rover Setup via Tracy
How to create new/edit receiver style
Base Station Setup
8www.javad.com
How to create new/edit receiver style
To create new or edit the saved receiver style, perform the following steps:
1. Switch to the extended mode using the top left corner menu button or View button:
Figure 1-9. Mode switch
2. Click the Configuration button.
3. In the Receiver tab click the button to add new receiver style or button to edit the
existing receiver style.
4. Specify the new style name, add the description and click Next:
Figure 1-10. Style name
Base and Rover Setup via Tracy
How to create new/edit receiver style
Base Station Setup
9www.javad.com
5. Select the correction source and click Next:
Figure 1-11. Correction source
6. Specify the base modem’s parameters, such as modem type, port modem is connected to,
baud rate, and type of corrections. Click Next:
Figure 1-12. Base modem parameters
Base and Rover Setup via Tracy
How to create new/edit receiver style
Base Station Setup
10 www.javad.com
7. In the next screen specify the UHF modem settings: protocol, modulation, link, output
power, frequency:
Figure 1-13. UHF modem settings
•Protocol - Simplex
•Modulation - DBPSK
•Link - 12.5 kHz
•Output power - up to 35 W.
8. In the next screen specify the TDMA multibase mode parameters:
Figure 1-14. TDMA multibase mode
Other manuals for TRIUMPH-1
4
Table of contents
Other Javad Receiver manuals
Javad
Javad TRIUMPH-VS User manual
Javad
Javad TRIUMPH-VS User manual
Javad
Javad TRIUMPH-2 Guide
Javad
Javad TRIUMPH-2 User manual
Javad
Javad GISmore User manual
Javad
Javad TRIUMPH-1 User manual
Javad
Javad TRIUMPH-1M User manual
Javad
Javad TRIUMPH-LS User manual
Javad
Javad UHFSSRx User manual
Javad
Javad DELTAGNSS Receiver User manual
