Javad TRIUMPH-1 Quick guide
All contents in this manual are copyrighted by JAVAD GNSS.
All rights reserved.The information contained herein may not be used, accessed, copied,
stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express
written consent from JAVAD GNSS.
GSM Base and Rover
Configuration Example
for TRIUMPH-1, SIGMA, and GISmore Receivers
Version 1.1
Last Revised August 18, 2009
www.javad.com
GSM Base & Rover Configuration Example
Base Station Configuration
4www.javad.com
3. Select the port receiver is connected to and click Connect (Figure 2-2).
Figure 2-2. ModemVU. Connection
4. Set the Radio and GSM parameters to OFF and click Apply.
5. Click Connect GSM button (Figure 2-3).
Figure 2-3. ModemVU ALPHA Internal Radio selection
6. In the Master/Slave tab set the following parameters, and click Apply (Figure 2-4):
Figure 2-4. Master/Slave tab settings
• Dial number: empty
•SendTimeOut:2
• Receive Time Out: 5
GSM Base & Rover Configuration Example
Base Station Configuration
5www.javad.com
7. In the General tab insert your SIM card PIN code (if needed), then set the mode to Slave,
and click Apply.
Figure 2-5. General tab settings
8. Wait until the modem will establish connection with net. The Modem status will be
ready (at first detecting, registration, than ready).
Figure 2-6. Modem status “ready”
9. Quit ModemVU by clicking Exit button.
GSM Base & Rover Configuration Example
Base Station Configuration
6www.javad.com
10. Start TriVU. Select port the receiver is connected to and click OK (Figure 2-7).
Figure 2-7. TriVU. Selecting port
11. Click ConfigurationReceiver.
12. In the Base tab click the Get from receiver button. Reference geodetic coordinates appear.
Click Apply (Figure 2-8).
Figure 2-8. Base tab
GSM Base & Rover Configuration Example
Rover Configuration
8www.javad.com
Rover Configuration
1. Start ModemVU.
2. Select Triumph 1X Internal Radio1and click OK (Figure 2-10).
Figure 2-10. ModemVU. Options window
3. Select the port receiver is connected to and click Connect (Figure 2-11).
Figure 2-11. ModemVU. Connection
4. Set the Radio and GSM parameters to OFF and click Apply.
1. For SIGMA receiver select SIGMA; for GISmore select GISmore
GSM Base & Rover Configuration Example
Rover Configuration
9www.javad.com
5. Click Connect GSM button (Figure 2-12).
Figure 2-12. ModemVU TRIUMPH Internal Radio selection
6. In the Master/Slave tab set the following parameters, and click Apply (Figure 2-4):
Figure 2-13. Master/Slave tab settings
• Dial number: phone number of the Base station’s SIM card.
• Send Time Out: 2
• Receive Time Out: 5
GSM Base & Rover Configuration Example
Rover Configuration
10 www.javad.com
7. In the General tab insert your SIM card PIN code (if needed), then set the mode to
Master, and click Apply;
Figure 2-14. General tab settings
8. Wait until the modem will establish connection with net: the Modem status will be at first
detecting, than registration. Wait until the connection with the Base will be
established: the Modem status will be at first dialing, than connected with the
connection baud rate value.
Figure 2-15. Modem status “connected”
9. Quit ModemVU by clicking Exit button.
Other manuals for TRIUMPH-1
4
This manual suits for next models
2
Table of contents
Other Javad Receiver manuals
Javad
Javad TRIUMPH-3NR User manual
Javad
Javad TRIUMPH-1 User manual
Javad
Javad TRIUMPH-1M User manual
Javad
Javad TRIUMPH-VS User manual
Javad
Javad TriPad User manual
Javad
Javad ALPHA User manual
Javad
Javad TRIUMPH-1M User manual
Javad
Javad DELTAGNSS Receiver User manual
Javad
Javad TRIUMPH-3 Guide
Javad
Javad TRIUMPH-VS User manual
