IQ DefinePro User manual
Define Set-Up Instructions
1. First, remove the battery insulator from the RED laser.
2. Mount the sight to the bow with the supplied hardware. (figure 1 a.)
3. Sight in top pin to 20 yards.
4. Hang supplied target at 20 yards to zero RED laser to sight.
5. Turn on RED laser to align to 20 yard pin on supplied target.
6. While holding 20 yard pin on zeroing target, determine
where RED laser is striking the target.
7. Depending on where your RED laser is impacting left and right
of the target, use the set screws (figure 1 b.) to align
the RED laser with the lower dot on the zeroing target.
(this may take a few attempts to get the laser directly below the pins on the zeroing target)
8. Alignment must always be checked at full draw.
9. Once the RED laser is directly in-line vertically with the pins, adjust the elevation. (figure 2)
10. To adjust the vertical elevation, slightly loosen the upper and lower mounting screws.
There should still be pressure on the bow sight but still allows the sight to move up and down.
11. Adjust the set screw clockwise to move the RED laser down.
Adjust the set screw counterclockwise to move the RED laser up.
12. Use the set screw to make vertical adjustments until the RED laser is
impacting the lower dot and the 20 yard pin is held on the upper dot.
(This may take a few iterations to complete)
13. Once this is complete, re-tighten your sight mounting screws.
14. Re-sight in your 20 yard pin.
15. Remove the RED laser. This is easily done removing the two machine screws.
*IQ does not condone hunting with the laser attached.
Please follow all Local and Federal hunting regulations.
16. Time to Adjust the Retina Lock. Flip over for instructions.
Activation of range finder
1. Unscrew the battery cover on the bottom of the sight and remove
the battery insulator.
2. Connect the trigger switch to the range finder port. (figure 3)
3. Mount the trigger switch to your preferred mounting location.
4. Depress the trigger once to activate the range finder to standby mode.
Depress the trigger a second time to put the range finder into scan mode.
Depress the trigger a third time to lock in desired range.
Depress a fourth time to return to scan mode.
*Accurate scans are done at full draw, using the 20 yard pin.
5. Scan mode will deactivate to standby mode after 2 minutes of no usage.
6. Standby mode will automatically shut off after 1 minute.
Pin Light LED
1. Depress the light switch on the side of the ranger finder to active pin lights. (figure 4)
2. There are 4 levels of pin brightness.
3. Pin light will automatically shut off after 1 hour.
Before mounting and setting up the Define, familiarize yourself
with the diagrams on the back of these instructions. They will be
a helpful tool to reference during set up.
Once set up is complete, the range finder is calibrated to the 20 yard pin.
When ranging a target on the range or in the field, use the 20 yard pin to mark
the target, then shoot using the appropriate pin.
The laser attachment on the Define is precision machined to align with
the scanning eye on the range finder. To ensure the Define marks the
desired target, it is imperative to follow these simple set up instructions.
figure 1
Left adjust Right adjust
Mounting holes
figure 2
Vertical adjust set screw
* when you move the set screw counterclockwise, you need to push
the laser up as the set screw is creating room for the sight to pivot
figure 3
Light switch
figure 4
Trigger button
These are adjusted at the same time
* loosen mounting screws before adjsuting.
Adjust Left
rear set screw clockwise
front set screw counterclockwise
Adjust Right
rear set screw counterclockwise
front set screw clockwise
PRO
PRO
1
5
0
TM
socket cap hex screw
split washer and washer
at head hex screw
Laser
*Never adjust these screws.
They are pre-calibrated for the DEFINE PRO.
Battery located in the back
a.
b.
Micro adjust Windage and Elevation dials
The Micro Adjust Windage and Elevation Dials allow
the shooter to make small, consistent, and accurate
adjustments as needed. They are also useful tools for
precision sight in.
Elevation dial
The laser etched Elevation Dial
precisely adjusts the pins up and
down. (clockwise moves pins down,
counterclockwise moves pins up)
Windage dial
The laser etched Windage Dial
precisely adjusts the pins left and right.
(clockwise moves pins right,
counterclockwise moves pins left)
Built in LED pin light
The built in pin light features
4 different intensities. Each
successive click brightens the
pins.
*Pins can be removed if archer prefers more open optics
by completely removing the machine screw on the
preferred pin and gently removing the pin housing
from the bezel.
Mounting holes Tool-free locking knobs
Vertical adjust set screw
Left adjust
Right adjust
Trigger Trigger plug in port
Fully captured .019” pins
Used to align 20 yard pin to laser during mounting and set up.
- Adjust clockwise to move laser down.
- Adjust counterclockwise to move laser up.
Used to align 20 yard pin to laser during mounting and set up
These are adjusted at the same time.
Adjust Micro adjust Winadge and Elevation dials without tools.
Adjust Left
rear set screw clockwise.
front set screw counterclockwise.
Adjust Right
rear set screw counterclockwise.
front set screw clockwise.
Depress the trigger once to activate the range finder to standby mode
Depress the trigger a second time to put the range finder into scan mode.
PRO
PRO
1
5
0
a) If you see the green Retina Lock™,
adjust the green Retina Lock™ until the
black dot is centered within the green
Retina Lock™ using the micro adjustments
located on the top and side of sight.
Remember you are adjusting the green
Retina Lock™ to fit your form/anchor point.
Repeat this step until the black dot is
centered in the green Retina Lock™ – at
your form/anchor point.
b) If you don’t see the green Retina Lock™
at your form/anchor point you will need to
move your anchor point up or down and
possibly left or right until you find the
green Retina Lock™. Once you’ve
determined the direction of the green
Retina Lock™, use the micro adjustments
located on the top and side of sight to
adjust the green Retina Lock™ to fit your
form/anchor point. The micro adjustment
on the top of the sight is to move the green
Retina Lock™ up and down and the micro
adjustment on the side of sight is to
move the green Retina Lock™ left and
right – REMEMBER YOU ARE MOVING
THE GREEN Retina Lock™. Repeat this
step until the black dot is centered in the
green Retina Lock™ – at your form/
anchor point.
Once your top pin and range finder are
accurately calabrated, it’s time to adjust
your Retina Lock™.
Draw your bow using the same
form/anchor point used to set your top pin
and look for the green Retina Lock™.
Set Up
micro adjustments
Up/DownLeft/Right
Once your black dot is centered in
the green Retina Lock™
AT YOUR FORM/ANCHOR POINT you can
now sight your pin in at other distances
and make your distance marks.
Quiver mounting holes
laser
20 yrd pin
SIGHT IN PAPER
PRO
PRO
1
5
0
Other IQ Measuring Instrument manuals
