Intersil ISL32740EVAL2Z User manual
Rev 1.00 Aug 2017
User’s Manual
ISL32740EVAL2Z
User’s Manual: Evaluation Board
Industrial Precision
UG125 Rev.1.00 Page 2 of 10
Aug 24, 2017
UG125
Rev.1.00
Aug 24, 2017
ISL32740EVAL2Z
Evaluation Board
USER’S MANUAL
1. Overview
The ISL32740EVAL2Z board enables the evaluation of the ISL32740EIAZ isolated, half-duplex PROFIBUS
transceiver in a typical bus node application, used in isolated industrial networks.
1.1 Key Features
• Industry’s smallest isolated PROFIBUS transceiver
• Drive capability of up to 160 bus transceivers
• Isolated 3.3V to 5V DC/DC converter with regulated output
• Small total device footprint of 183mm2
1.2 Specifications
This board has been configured and optimized for the following operating conditions:
• Up to 40Mbps data rate
•V
CC = 3.3V
1.3 Ordering Information
1.4 Related Literature
• For a full list of related documents, visit our website
•ISL32740E product page
Part Number Description
ISL32740EVAL2Z ISL32740EIAZ evaluation board
Figure 1. Block Diagram
LOGIC
I/O
RS-485
I/O
3.3V
SUPPLY
J5J2
J1
ISL32740EIAZ
ISOLATED
PROFIBUS
TRANSCEIVER
ISOLATED
DC/DC
CONVERTER
5V
3
UG125 Rev.1.00 Page 3 of 10
Aug 24, 2017
ISL32740EVAL2Z 2. Functional Description
2. Functional Description
The ISL32740E is an isolated, 40Mbps, half-duplex PROFIBUS transceiver. The device incorporates a patented refresh
circuit to maintain the correct output state with respect to data input. At power-up, the bus outputs follow the Truth Tables.
The DE input should be held low during power-up to prevent false drive data pulses on the bus. This is accomplished by
connecting DE through a 10kΩ pull-down resistor to GND1.
This transceiver uses a differential input receiver for maximum noise immunity and common-mode rejection. Input
sensitivity is ±200mV, as required by the RS-485 specification.
The receiver input resistance meets the PROFIBUS “Unit Load” (UL) requirement of 54kΩ minimum. The receiver
includes a “fail-safe if open” function that ensures a high-level receiver output if the receiver inputs are unconnected
(floating). The receiver output is tri-statable through the active low RE input.
The PROFIBUS driver is a differential output device that delivers at least 2.1V across a 54Ω purely differential load.
The driver features low propagation delay skew to maximize bit width and to minimize EMI.
The driver in the ISL32740E is tri-statable using the active high DE input. The outputs of the ISL32740E driver are not
slew rate limited, so faster output transition times allow data rates of at least 40Mbps.
Important Notice:
For convenience, an isolated DC/DC converter is used to provide the power supply across the isolation barrier. Its
isolation ratings, however, are lower than those of the transceiver. Therefore, ensure that the ground potential
difference between the left side (GND1, GND2) and the right side (GND3, GND4) of the board remain below 50VAC
(see Figure 2 on page 4).
2.1 Truth Tables
Note: *Transceiver shutdown mode.
Receiving
Inputs Outputs
RE DE A-B RO
00 V
AB ≥ -0.05V 1
0 0 -0.05 > VAB > -0.2V Undetermined
00 V
AB ≤ -0.2V 0
0 0 Inputs Open/Shorted 1
1 1 X High-Z
1 0 X High-Z*
Transmitting
Inputs Outputs
RE DE D ISODE B A
X11101
X10110
0 0 X 0 High-Z High-Z
1 0 X 0 High-Z* High-Z*
UG125 Rev.1.00 Page 4 of 10
Aug 24, 2017
ISL32740EVAL2Z 3. PCB Layout Guidelines
3. PCB Layout Guidelines
Both supplies, VDD1 and VDD2, must be bypassed with 100nF ceramic capacitors. For proper operation, these should
be placed as close as possible to the supply pins.
3.1 ISL32740EVAL2Z Evaluation Board
Figure 2. Top Side
Figure 3. Bottom Side
UG125 Rev.1.00 Page 5 of 10
Aug 24, 2017
ISL32740EVAL2Z 3. PCB Layout Guidelines
3.2 ISL32740EVAL2Z Circuit Schematic
Figure 4. Schematic
ISL32740EIAZ
A
A
C3
10UF
DE
A
C2
0.1UF
J1-4 1
GND4
D
J5-4
1
R7
10K
J1-3 2
GND3
R1
10K
J5-3
2
R3
10K
J2-4 1
1
2
4
5
6
7
8
3
9
10
11
12
13
14
15
16
U1
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
J5-2
3
J2-3 2
R6
549
R2
10K
J5-1
4
+VOUT
-VOUT
NC
-VIN -VOUT
+VIN
U2
R1Z-3.305/P
1
2
4
5
7
10
J2-2 3
R5
133
J2-1 4
R4
549
C1
10UF
C4
0.1UF
R
B
GND2
RE#
GND1
UNNAMED_1_QSOP16_I1_PIN12
UNNAMED_1_QSOP16_I1_PIN6
UNNAMED_1_R1Z_I40_2
UNNAMED_1_SMRES_I28_B
UNNAMED_1_SMRES_I29_B
UNNAMED_1_SMRES_I2_A
UNNAMED_1_SMRES_I30_B
UNNAMED_1_SMRES_I3_A
UNNAMED_1_R1Z_I40_7
UG125 Rev.1.00 Page 6 of 10
Aug 24, 2017
ISL32740EVAL2Z 3. PCB Layout Guidelines
3.3 Bill of Materials
Manufacturer
Part Qty
Reference
Designator Description Manufacturer
ISL32740EVAL2ZREVAPCB 1 PWB-PCB, ISL32740EVAL2Z, REVA, ROHS IMAGINEERING INC
ISL32740EIAZ 1 U1 ISOLATED, 40MBPS, HALF-DUPLEX PROFIBUS
TRANSCEIVER, ROHS
Intersil
R1Z-3.305/P 1 U2 ISOLATED 3.3V-TO-5V DC/DC CONVERTER
WITH REGULATED OUTPUT, ROHS
RECOM-POWER
CR0805-8W-1002FT 4 R1-R3, R7 RES, SMD, 0805, 10k, 1/8W, 1%, TF, ROHS VENKEL
RK73H2AT1330F 1 R5 RES, SMD, 0805, 133Ω, 1/8W, 1%, TF, ROHS KOA
RC0805FR-07549RL 2 R4, R6 RES, SMD, 0805, 549Ω, 1/8W, 1%, TF, ROHS YAGEO
C0805X5R160-106KNE 2 C1, C3 CAP, SMD, 0805, 10µF, 16V, 10%, X5R, ROHS VENKEL
ECJ-2VB1E104K 2 C2, C4 CAP, SMD, 0805, 0.1µF, 25V, 10%, X7R, ROHS PANASONIC
1725656 1 J1 CONN-TERMINAL BLK, TH, 2P, 6A, 125V,
20-30AWG, 2.54mm, ROHS
PHOENIX CONTACT
1725672 2 J2, J5 CONN-TERMINAL BLOCK, 4POS, 0.1, 26-20AWG,
63V, 6A, ROHS
PHOENIX CONTACT
5001 4 GND1 - GND4 CONN-MINI TEST PT, VERTICAL, BLK, ROHS KEYSTONE
5003 6 A, B, D, R, DE, RE# CONN-MINI TEST POINT, VERTICAL, ORG, ROHS KEYSTONE
S-2261 1 Place assy in bag BAG, STATIC, 4x6, ZIPLOC, ROHS ULINE
LABEL-DATE CODE 1 AFFIX TO BACK
OF PCB
LABEL-DATE CODE_LINE 1: YRWK/REV#, LINE 2:
BOM NAME
Intersil
UG125 Rev.1.00 Page 7 of 10
Aug 24, 2017
ISL32740EVAL2Z 3. PCB Layout Guidelines
3.4 Board Layout
Figure 5. Silkscreen Top Figure 6. Top Layer
Figure 7. Silkscreen Bottom Figure 8. Bottom Layer
UG125 Rev.1.00 Page 8 of 10
Aug 24, 2017
ISL32740EVAL2Z 3. PCB Layout Guidelines
3.5 Typical Performance Curves
Figure 9. Transmit Mode Figure 10. Receive Mode
TIME: 10ns/DIV
SIGNAL: 2V/DIV
DI
A
B
TIME: 10ns/DIV
SIGNAL: 2V/DIV
RO
A
B
ISL32740EVAL2Z 4. Revision History
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the
reader is cautioned to verify that the document is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
© Copyright Intersil Americas LLC 2017. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
UG125 Rev.1.00 Page 9 of 10
Aug 24, 2017
4. Revision History
Rev. Date Description
1.00 Aug 24, 2017 Updated truth tables.
0.00 Jul 20, 2017 Initial release
ISL32740EVAL2Z
UG125
Table of contents
Other Intersil Motherboard manuals
Intersil
Intersil ISL70321SEHDEMO1Z User manual
Intersil
Intersil ISL282x6EVAL1Z User manual
Intersil
Intersil ISL5585EVAL4 User manual
Intersil
Intersil ISL97684 User manual
Intersil
Intersil ISL59420/21EVAL1 User manual
Intersil
Intersil ISL281X7MSOPEVAL1Z User manual
Intersil
Intersil ISL55141 User manual
Intersil
Intersil ISL54200EVAL1Z User manual
Intersil
Intersil ISL3331EVAL1Z User manual
Intersil
Intersil ISL45042EVAL1Z User manual
Intersil
Intersil ISL97671A User manual
Intersil
Intersil ISL76683 User manual
Intersil
Intersil ISL97683 User manual
Intersil
Intersil ISL32741EVAL1Z User manual
Intersil
Intersil ISL8201M User manual
Intersil
Intersil ISL6442 User manual
Intersil
Intersil ZL2005P User manual
Intersil
Intersil ISL71026MEVAL1Z User manual
Intersil
Intersil JESD204B User manual
Intersil
Intersil ISL62881CGPUEVAL2Z User manual
