Insize ISQ-TS120K User manual

MN-ISQ-TS120K-E

ISQ-TS120K

DIGITAL LED

TACHOMETER/STROBOSCOPE

OPERATION MANUAL

www.insize.com

Warning

Please closely follow all safety precaution.

Be sure to read the entire instruction manual thoroughly

before initial set-up, operation and maintenance. The instruction

manual provides two grades of safety warnings: “Danger” and

“Caution”. The precautions described here with concern the

safety of the operator are to be read carefully. Follow these

precautions.

“Danger” marking indicates possible death, severe injury or

fire if the user disregards the instruction.)

“Caution” marking indicates the possibility of minor injury or

object damage if the user operates the equipment improperly.

Disregard to this message may cause severe injury. Be sure to

follow the following types of content, and distinguish between

description.

Danger

Caution

This warning indicates a prohibited operation.

This warning indicates constraint of content.

Danger

Use in flammable environments is prohibited.

Use in this manner may result in fire or explosive.

Don’t look directly into the LED light source.

This may result in eye injury.

Caution

Do not drop. Damage or injury may result.

Don’t use or restore in the following environments. Direct

sunshine, condensation, dust or caustic.

4.6.3 LCD back light off

The LED backlight will automatically shut off after 2 minutes

of no keypad or dial operation when using the LCD backlight

will light again with keypad or dial operation.

4.7.1 Charging round socket:

4.7.2 External synchronous USB port

1. +12V output

2. OUT external pulse input

3. -12V output

4.7.3 External Pulse input

The unit can be operated and controlled by an external

signal, from either a sensor or machine signal.

This will allow the stroboscope to flash in sync with the

target object’s rotational speed.

The input signal will have the following characteristics.

Input frequency: 60-120,000fpm(1-2000Hz)

Input pulse width: over 50us

Delay angle: 0-359°(every 1°)

Delay time: 0-999ms(every 1ms)

Note: when the external sensor is used, please use the AC

adapter otherwise, there is no voltage on the sensor port.

4.7 Connector of External input/output

Do not alter, modify or dispose of improperly. Such action may

cause damage accidents and void warranty.

Operate with 0-35℃(32-95℉), 35-38%RH Use outside of this

range may alter operation of the unit.

To clean, gently wipe with a soft cloth.

This unit may become excessively hot when used

continuously for more than 2 hours.

Summary

This LED stroboscope is our latest new technology product,

which use America CREE high power LED lamps and have the

characteristics of wide measurement range, high brightness, long

life time, they can be used any time, any place. With convenient

operation, the build in lithium rechargeable batteries, single use

time is more than 12 hours. This stroboscope is used to measure

the motions of objects, when the strobe flash speed and

highspeed moving objects are in synchronous fast moving

objects and working status of all kinds of gears and rotors during

working. This stroboscope can be widely used in paper,

packaging, printing industries to inspect the high speed printing

process, ink color matching, die cutting, hole punching and and

folding quality. For textile industry, it can be used to detect the

spindle and thread speed on spindle machine and coiling

machine and inspect the working condition and status of the

mechanical knitting, weaving machine and sewing machine.

When used in mechanical manufacturing, industries, it can be

used for the non contact rpm speed measurement and other

mea s urem e nt. Be s ide, i t c an als o b e u sed in a ircra f t

manufacturing, automotive manufacturing, cable and wire

m a nu fa ct u r i ng , m in i n g , s hi p b u i ld in g, s te el , c h e m ic al ,

pharmaceutical, optional, electronic, food-processing and other

industries.

4.6.1 LED flashing auto off

The LED flashing will automatically turn off after 2 minutes

of no keypad or dial operation when using battery power.

Flashing will resume with either a dial (rotation) movement or

a keypad operation.

The LED auto shutoff will not occur in External trigger

mode, while a signal is being received by the unit. The LED

flashing will automatically turn off after 2 minutes of no

external pulse input.

4.6.2 Auto off Power off

The unit will automatically power off after 5 minutes of no

keypad or dial operation when using battery power. To resume

operation, press “POWER” key.

The auto power shutoff will not occur in External trigger

mode, while signal is being received by the unit. The power

will automatically turn off after 2 minutes of no external pulse

input.

Operation Expression

Press and

release OR

Press and

release OR

4.6 Power-saving settings

Setting accuracy(Vibration):

S Vibration

±0.01%

et the resolution( ):

60 ~ 120000FPM (Flash Per Minute) 0.1 FPM

1~200Hz 0.01Hz

LED Spec: USA CREE 10W LED light, life time is 3-5 years.

Battery: DC10.8V 200mA

Power: About 30W

Dimension: 208mmx70mmx60mm

Net weight: .380g

Main features:

1) Two units of measure-FPM(Flash Per Minute) and Hz

2) Wide flash range-60 to 120,000FPM

3) Multiply or divide by 2

4) Phase shift function “-” or “+” to “ +3°”, “ +3°”

5) Adjustable flash duration-(RATIO) Time can change for

0.1°each time as in the range if 0.1°-2.5°.

6) External input/output port-Synchronization of flash rate

with external pulse, and output the pulse signal with flash

rate.

2.1 Confirmation of product packaging

Confirmation the following four parts in your pachage;

1) One LED stroboscope

2) One AC/DC Adapter: 220V/DC16V/3A

3) One set of external input/output connector

4) Operation manual

Production inspection and preparetion

Components

For details, please refers to: 4.4.3.2 delay angle setting.

Rotate the dial clockwise to increase delay angle setting or

counter clockwise to decrease the delay angle.

4.5.3 Back light setting

The LCD display of the stroboscope has a backlight that can

be turned on or off in the parameter settings. Turning off the

backlight will conserve battery power. For more information

regarding the automatic setting of the backlight, see section

4.6.

To adjust the backlight setting, enter parameter mode and

use the “SET” key to cycle to LCD settings.

Press “PHASE+” key to turn on the backlight. Press

“PHASE-” key to turn off the backlight.

4.5.2.2 Delay angle setting

As period of external input is 360°, the delay angle can be

set form 0° to 360° by every 1°. Delay angle setting increases

as the dial turns right, and decrease as it turns left.

Delay angle will go to 0° as its settings increase from 359°,

and it goes to 359° as the angle decrease from 0°.

Operation Expression

To delay angle

setting

To delay angle

setting

No.

POWER key

SET key

½ key

Function Instructions

MODE key

RATIO key

PHASE “+” key

PHASE “-” key

Power the unit on and off

Select mode of operation:

Internal/External/Parameter

x2 key

Unit change, select parameter setting item,

store setting value

Advance image forward 3degree at a time in

internal mode. In parameter setting mode,

change setting value.

Retard image backwards 3 degree at a time in

internal mode. In parameter setting mode,

change setting value.

Multiplies the flash rate/frequency by a

factor of 2.

Name

Divides the flash rate/frequency by a

factor of 2.

Adjust flash duration(Flash pulse width)

in Internal/External mode

9Dial

Set flash rate or frequency.

CW; Increase flash rate/frequency.

CCW; Decrease flash rate/frequency.

(Turn dial quickly to drastically change value,

Turn dial slowly to change value 1 dight.)

In parameter setting mode, CW or CCW

rotation changes the setting value.

10 ECO key

Reduce the brightness of LED, thereby saving

battery power. Push again to return to original

brightness setting.

4.5.2 Delay setting

Delay time angle setting will allow the flash to be delayed

after an external pulse is transmitted to the stroboscope. It

can be set in either external trigger mode, or in parameter

setting mode. The following section details the parameter

setting mode. Press MODE key to either external trigger

mode, and press SET key 3 times to enter Delay setting.

Through setting of delay time of flashing angle, the trigger

flashing of external pulse input can be delayed.

Press “PHASE+” and “PHASE-” key, to select between

delay time and delay angle.

4.5.2.1 Delay time setting

Selecting delay time angle form an external pulse input to

LED flashing can be set in the range of 0-999ms, with a

resolution or 1ms.

For details, please refers to: 4.4.3.1 delay time angle

setting.

Rotate the dial clockwise to increase delay time angle

setting or counter clockwise to decrease the delay time angle.

Operation Expression

To delay angle

setting

To delay angle

setting

3.3.1 Display Names and Descriptions

3.3 LCD Display

Battery

Setting

project

Sub data

Main data display

Unit

3.3.2 Main data display

-Flash rate value will be displayed in internal flashing mode.

-The frequency of external trigger will be displayed in

external trigger mode.

-Display will indicate “P” or “LCD”(in ON/OFF setting of LCD

backlight ) in *parameter setting mode.

*For details about parameter setting mode, please refer to

“4.5 parameter setting mode”

3.3.3 Sub data display

Internal mode display

-Display will indicate degree pg phase shift in internal

flashing mode. To change the degree of phase shift, press

PHASE + or PHASE - keys. The display will reflect the

cumulative angle of phase shift.

When press RATIO, trigger angle will display on LCD.

Adjust dial or press +, - to change flash time(The flash time

range is 0.1 to 2.5)

External mode display

-In external trigger mode, the display will show the setting

of delay time. For details about changing these settings,

please see section 4.4.3

*Parameter mode display

-In parameter mode, the display will indicate the following

settings: -selected measuring range

-Delay time(in ms)

-Backlight LCD(ON or OFF)

*For details about *parameter setting mode, please refer to

4.5 parameter setting mode

3.3.4 Function mode

The following will be displayed, according to the mode of

measure and *parameter setting.

Delay time(based on the delay settings of parameter)

When trigger edge setting is set to “down edge”. The flash

will occur on the trailing edge of the input pulse(when delay

setting is zero).

Example: When trigger edge setting is set to “up edge”. The

flash will occur on the leading edge of the input pulse(when

delay setting is zero).

External pulse signal

from machine/sensor

stroboscope flash

External pulse signal

from machine/sensor

stroboscope flash

Delay time(based on the delay settings of parameter)

When in parameter mode, use the SET key to cycle to the

Trigger Edge setting parameter mode. To set the trigger edge

as “Down Edge”, press “PHASE-” key or turn the dial counter

clockwise. To set the trigger edge as “Up Edge”, press

“PHASE+” key or turn the dial clockwise.

Operation

Press and release

Expression

Press and release

Trigger edge set as “up edge” Trigger edge set as “down edge”

Trigger edge set as “up edge”Trigger edge set as “down edge”

Internal flashing mode

- Set the positive edge in external trigger mode

- Set the negative edge in external trigger mode

- Set the measuring range in parameter setting mode*

Set the flash time

- Choose UP when set trigger edge in *parameter setting

mode

- Choose DOWN when set trigger edge in *parameter

setting mode

- Choose angle setting when delay set in *parameter setting

mode

- Choose delay setting when delay set in *parameter setting

mode

Set backlight LCD(ON or OFF)

- Set backlight LCD display time two ways of external

trigger modes setting

Factory Initialize settings

Parameter store settings

For more information regarding the parameter setting, please

see section 4.5

3.3.5 Battery indication

Battery capacity

is full

The battery capacity

is diminished

When battery is empty,

the unit will power off

and show “please

charge battery”

The display will indicate a battery charge when the unit is

being used with the AC/DC adapter.

When the voltage of the battery is lower than the operating

voltage, the display will indicate “Please charge battery”.

Each time after charging the battery, the unit could keep

working for more than 12hours.

4.5.1 Trigger edge setting(external modes)

In external mode, the trigger edge parameter will allow for

selecting either the leading edge or trailing edge of the input

pulse to trigger the stroboscope flash.

Operation

Press and release Measuring range

setting(press +, - key

or turn the dial to

switch the measuring

range)

Trigger edge setting

(press +,- key or turn

the dial to switch the

trigger edge setting)

Delay time setting

(use dial or PHASE

key to change

settings)

Expression

Press and change

the selected

parameter setting

Rotate the dial

to change the

selected

parameter

setting

Shut delay time LCD backlight

(press +,- key or turn

the dial to change the

backlight settings)

Delay angle setting

(use dial or PHASE

keys to change

settings)

LCD delay time set the parameter value set the length

Save parameter setting

Then back to the

“Trigger edge setting”

Initialize settings Set the software

serial number

MODE: set and store parameter settings

POWER: turn off unit without saving parameter settings

When the unit is off, press the POWER key to turn on the unit.

The unit begin to flash in internal mode and the display will

indicate the flash rate(FPM=flashes per minute).

4.1 Power on/off

Function Instructions

Operation

Power off

Press and release

LCD light will begin

to flash. Display flash

rate of internal mode.

Indication

When the unit is on, press the POWER key to turn off the unit.

The display will turn off, and the unit stop flashing.

Operation

Power off

Press and release

Display turn off and

unit stop flashing.

Indication

4.2 Mode section

To switch between INTERNAL, EXTERNAL and

*PARAMETER mode, press and release the MODE key. For

details about parameter setting mode, please refer to 4.5

parameter setting mode.

Operation Indication

Press and release

to switch modes Internal flashing mode External trigger mode Parameter setting mode

turned clockwise, and increase as it is turned counter

clockwise.

4.4.5 ECO feature

To reduce the brightness and conserve battery power, press

the ECO key. To turn original brightness, press and release

the ECO key again.

To enter parameter setting mode, press “MODE” until the

LCD display “P”.

When the display shows “P”, press the SET key to cycle

between the various parameter settings available(range,

trigger edge, delay time, and LCD backlight etc). For more

information regarding the various parameter settings, please

refer to sections 4.5.2 through 4.5.4 below. To store the

settings and return to measuring modes, press the MODE key.

Note: MODE key must be pressed to store settings.

Pressing the POWER key will not store the parameter settings

in memory.

Operation

Press and release

Expression

Normal flashing mode ECO flashing mode Return to normal

flashing mode

4.5 Parameter settings instruction

4.3.1 Instruction for internal flashing mode

4.3 Internal flashing mode

Battery power

indication

Flashing time

(Hz shown) setting

Speed mode

4.3.2 Changing units of measure in internal mode

To change the measuring units from fpm to Hz, press and

release the SET key.

Operation

Press and release Measuring unit “fpm”

Indication

Measuring unit “Hz” Measuring unit “fpm”

Note: each time press “SET” key, unit of measure (fpm) will

convert to the new unit of measure(Hz) and return this.

4.3.3 ECO function

Press “ECO” button, can enter the power saving mode, at this

time, the LED brightness is 60% of the original, stroboscope

can be used for longer time.

Operation

Press and release Normal flashing mode

Indication

ECO flashing mode Return to normal

flashing mode

4.3.4 Flash rate and frequency setting in internal mode

You can set the flash rate(frequency) by turning the strobe

encoder on the turntable. To increase the flash rate, turn the

dial in the clockwise direction. To release the flash rate, turn

the dial in the counter-clockwise direction.

For small adjustments, turn the dial slowly. For quick

djustment, rotate the dial quickly. The flash rate range and a

flashes at the delay angle=0°.

Delay angle increase as the dial is rotated to the right. The

angle settings will go to 0°as the angle increase past 359°.

4.4.4 Units of measurement-changing from FPM to Hz

To change the units of measure “FPM” to “Hz” while in

External Trigger ring made, press and release the “SET” key.

Turn clockwise

Expression

Delay angle decrease as the dial is rotated to the left. The

settings will eventually go to 0°as the angle decrease past

359°.

Turn counter

clockwise

Expression

Operation

Press and release

Measuring unit “fpm” Measuring unit “Hz” Measuring unit “fpm”

Expression

Note: As the display ed value changes, fraction generated.

Table of contents

Other insize Measuring Instrument manuals

insize

insize ISH-SDM Installation manual

insize

insize ISU-300D User manual

insize

insize PLUS 3631 Series User manual

insize

insize ISF-DF Series User manual

insize

insize 1113INS Technical manual

insize

insize ISN-L70 User manual

insize

insize ISU-200D User manual

insize

insize ISF-1DF Series User manual

insize

insize ISH-DSD User manual

insize

insize 1149 Series Technical manual

insize

insize ISU-250C User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

insize ISQ-TS120K User manual

Popular Measuring Instrument manuals by other brands