IFM Efector 200 O6E4 User manual
Operating instructions
Through-beam sensor
O6E4 / O6S4
O6E400 / 00 10 / 2015
UK
2
1 Preliminary note
1.1 Symbols used
►Instruction
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunctions or interference.
2 Functions and features
The through-beam sensor detects objects and materials without contact and
indicates their presence by a switching signal.
3 Installation
Transmitter Receiver
►Install the receiver (O6E...) and secure it to a bracket.
►Align the transmitter (O6S...) to the receiver and fix it.
Maximum range only with accurate alignment.
3
UK
4 Operating and display elements
1: LED green - operation
Transmitter
1: LED yellow - switching output active
2: Setting potentiometer „sensitivity“
3: LED green - operation
4: Selector „output function“
Receiver
4.1 Stability indication
The green LED is lit when the supply voltage is applied and the sensor signal is
stable.
stable signal switch point stable signal
Light-on mode
LED green on off off on
LED yellow on on off off
Dark-on mode
LED green on off off on
LED yellow off off on on
4
5 Electrical connection
The unit must be connected by a qualified electrician.
►The national and international regulations for the installation of electri-
cal equipment must be adhered to.
►Ensure voltage supply to EN 50178.
►Disconnect power.
►Connect the unit as follows:
5.1 Transmitter
Connector M12 pigtail Cable *
1
3
L+
L
Connector M8 3-pin Connector M8 4-pin
1
3
L+
L
2
1
4
3
1
3
L
+
L
* Core colours: BN = brown, BU = blue, BK = black
5.2 Receiver
5.2.1 PNP
Connector M12 pigtail Cable *
Connector M8 3-pin Connector M8 4-pin
2
1
4
3
* Core colours: BN = brown, BU = blue, BK = black
5
UK
5.2.2 NPN
Connector M12 pigtail Cable *
L+
L
1
4
3
L
BN
BK
BU
L+
Connector M8 3-pin Connector M8 4-pin
L+
L
1
4
3
2
1
4
3
L+
L
1
4
3
* Core colours: BN = brown, BU = blue, BK = black
6 Settings
6.1 Set the output function
DL
►Setting D: dark-on mode
►Setting L: light-on mode
Receiver
6.2 Set the sensitivity
►Increase sensitivity:
turn the setting screw of the potenti-
ometer clockwise.
►Decrease sensitivity:
turn the setting screw of the potenti-
ometer anti-clockwise.
Receiver
6
7 Operation
►Check whether the unit operates correctly.
> The green LED is lit when the sensor is ready for operation.
> Dark-on mode: the output is switched / the yellow LED is lit when an object is
detected.
> Light-on mode: the output is switched / the yellow LED is lit when no object is
detected.
8 Maintenance, repair, disposal
►Keep the lens of the sensor free from soiling.
►For cleaning do not use any solvents or cleaning agents which could damage
the plastic parts.
►After use dispose of the unit in an environmentally friendly way in accordance
with the applicable national regulations.
Faulty sensors must only be repaired by the manufacturer.
Technical data and further information at unter www.ifm.com
This manual suits for next models
1
Table of contents
Other IFM Accessories manuals
IFM
IFM IFS Series User manual
IFM
IFM JD Application guide
IFM
IFM PI109 Series User manual
IFM
IFM LI513 Series User manual
IFM
IFM efector 200 OGS38 Series User manual
IFM
IFM KB User manual
IFM
IFM PN7160 User manual
IFM
IFM efector160 LR2750 User manual
IFM
IFM UGR500 User manual
IFM
IFM efector 200 OGP2 Series User manual
IFM
IFM O1D300 User manual
IFM
IFM EIO404 User manual
IFM
IFM OGP7 Series User manual
IFM
IFM Efector 160 LK8 User manual
IFM
IFM PQ3 Series User manual
IFM
IFM O5D15 Series User manual
IFM
IFM PN00 A Series User manual
IFM
IFM JD Series Application guide
IFM
IFM Efector 200 Series User manual
IFM
IFM O4E5 Series User manual
