IFM PQ3 Series User manual

Operating instructions
Pressure sensor
PQ3xxx UK
80007230 / 00 06 / 2019

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������3
1�1 Symbols used ������������������������������������������������������������������������������������������������3
2 Safety instructions �����������������������������������������������������������������������������������������������3
3 Functions and features ����������������������������������������������������������������������������������������4
3�1 Use of the main connection G1/8 ������������������������������������������������������������������4
3�2 Use of the auxiliary connection M5����������������������������������������������������������������5
4 Function���������������������������������������������������������������������������������������������������������������5
4�1 Output signals������������������������������������������������������������������������������������������������5
4�2 Switching function������������������������������������������������������������������������������������������5
4�3 IO-Link �����������������������������������������������������������������������������������������������������������6
4�3�1 General information ������������������������������������������������������������������������������6
4�3�2 Device-specific information�������������������������������������������������������������������6
4�3�3 Parameter setting tools�������������������������������������������������������������������������6
5 Installation������������������������������������������������������������������������������������������������������������7
5�1 Mounting accessories������������������������������������������������������������������������������������7
5�2 DIN rail mounting�������������������������������������������������������������������������������������������7
5�3 Panel mounting����������������������������������������������������������������������������������������������8
6 Electrical connection��������������������������������������������������������������������������������������������8
7 Operating and display elements ��������������������������������������������������������������������������9
8 Menu������������������������������������������������������������������������������������������������������������������10
8�1 Menu structure���������������������������������������������������������������������������������������������10
8�2 Explanation of the menu������������������������������������������������������������������������������ 11
9 Parameter setting ����������������������������������������������������������������������������������������������12
9�1 Parameter setting in general �����������������������������������������������������������������������12
9�2 Set output signals ����������������������������������������������������������������������������������������14
9�2�1 Set the unit of measurement for system pressure������������������������������14
9�2�2 Set the output function������������������������������������������������������������������������14
9�2�3 Set the switching limits (hysteresis function) ��������������������������������������14
9�2�4 Set the switching limits (window function) ������������������������������������������14
9�3 User settings (optional)��������������������������������������������������������������������������������15
9�3�1 Set delay for the switching outputs�����������������������������������������������������15
9�3�2 Set damping for the switching outputs������������������������������������������������15

3
UK
1 Preliminary note
1.1 Symbols used
►Instruction
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunction or interference�
2 Safety instructions
• The device described is a subcomponent for integration into a system�
- The manufacturer of the system is responsible for the safety of the system�
- The system manufacturer undertakes to perform a risk assessment and to
create a documentation in accordance with legal and normative requirements
to be provided to the operator and user of the system� This documentation
must contain all necessary information and safety instructions for the operator,
the user and, if applicable, for any service personnel authorised by the
manufacturer of the system�
• Read this document before setting up the product and keep it during the entire
service life�
9�3�3 Configuration of the display ����������������������������������������������������������������15
9�3�4 Zero-point calibration��������������������������������������������������������������������������16
9�3�5 Differential pressure measurement: optimisation of the sensor
accuracy �������������������������������������������������������������������������������������������������������16
9�4 Service functions �����������������������������������������������������������������������������������������16
9�4�1 Read min/max values for the system pressure ����������������������������������16
9�4�2 Reset all parameters to factory setting �����������������������������������������������17
10 Operation���������������������������������������������������������������������������������������������������������17
10�1 Read set parameters ���������������������������������������������������������������������������������17
10�2 Error indications�����������������������������������������������������������������������������������������17
11 Factory setting �������������������������������������������������������������������������������������������������18

4
• The product must be suitable for the corresponding applications and
environmental conditions without any restrictions�
• Only use the product for its intended purpose (→ Functions and features).
• Only use the product for permissible media (→ Technical data).
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property may occur�
• The manufacturer assumes no liability or warranty for any consequences
caused by tampering with the product or incorrect use by the operator�
• Installation, electrical connection, set-up, operation and maintenance of the unit
must be carried out by qualified personnel authorised by the machine operator�
• Protect units and cables against damage�
3 Functions and features
The unit monitors the system pressure/differential pressure in compressed air
networks and pneumatic systems of machines and plants�
Avoid static and dynamic overpressure exceeding the specified overload
pressure by taking appropriate measures�
The indicated bursting pressure must not be exceeded�
Even if the bursting pressure is exceeded only for a short time, the unit
may be destroyed� ATTENTION: Risk of injury!
Pressure Equipment Directive (PED): The units comply with section 3,
article (3) of the Directive 97/23/EC and are designed and manufactured
for media of fluid group 2 (stable gases and non-superheated liquids) in
accordance with the sound engineering practice�
3.1 Use of the main connection G1/8
Application: compressed air (other media on request); type of pressure: relative
pressure
Order no. Measuring range Permissible
overload pressure Bursting pressure
bar PSI bar PSI bar PSI
PQ3809 -1���1 -14�6���14�5 20 290 30 435
PQ3834 -1���10 -15���145 20 290 30 435
MPa = bar ÷ 10 / kPa = bar × 100

5
UK
3.2 Use of the auxiliary connection M5
Observe the respective notes in these instructions for measurement
accuracy optimisation for differential pressure measurements (→ chapter
9�3�5 Differential pressure measurement)�
Application: compressed air (other media on request); use for differential
pressure measurement; connection of the low pressure side�
In particular for filter monitoring, the output side of the filter (i�e� the lower
pressure level) is connected to the auxiliary connection M5 while the input side
of the filter is connected to the G1/8 connection (→ chapter 3.1 Use of the main
connection G1/8, → chapter 5 Installation). Observe the following pressures in this
application:
• Permissible overload pressure in the auxiliary connection as opposed to the
main connection: 2 bar / 29 PSI�
• Bursting pressure of the auxiliary connection as opposed to the main
connection: 12 bar / 174 PSI�
4 Function
4.1 Output signals
• The unit displays the current system pressure (with use of the main connection
G1/8 only) or the differential pressure (with additional use of the auxiliary
connection M5)�
• It generates 2 output signals according to the parameter setting�
OUT1 Switching signal for limit value / IO-Link
OUT2 Analogue output 4���20 mA (fixed across the measuring range of the sensor)
4.2 Switching function
OUT1 changes its switching state if it is above or below the set switching limits
(SP1, rP1)� The following switching functions can be selected:
• Hysteresis function / normally open: [ou1] = [Hno] (→ Fig. 1).
• Hysteresis function / normally closed: [ou1] = [Hnc] (→ Fig. 1).
First the set point (SP1) is set, then the reset point (rP1) with the requested
difference�
• Window function / normally open: [ou1] = [Fno] (→ Fig. 2).
• Window function / normally closed: [ou1] = [Fnc] (→ Fig. 2).

6
The width of the window can be set by means of the difference between FH1 and
FL1� FH1 = upper value, FL1 = lower value�
1 2
P = system pressure / differential pressure; HY = hysteresis; FE = window
4.3 IO-Link
4.3.1 General information
This unit has an IO-Link communication interface which requires an IO-Link-
capable module (IO-Link master) for operation�
The IO-Link interface enables direct access to the process and diagnostic data
and provides the possibility to set the parameters of the unit during operation�
In addition communication is possible via a point-to-point connection with a USB
adapter cable�
You will find more detailed information about IO-Link at www�ifm�com�
4.3.2 Device-specific information
You will find the IODDs necessary for the configuration of the IO-Link unit and
detailed information about process data structure, diagnostic information and
parameter addresses at www�ifm�com�
4.3.3 Parameter setting tools
You will find all necessary information about the required IO-Link hardware and
software at www�ifm�com�

7
UK
5 Installation
Before installing and removing the unit: Make sure that no pressure is
applied to the system�
►Screw the pressure connection or adapter G1/8 to
the main pressure connection (1) and tighten:
• Maximum tightening torque: 8 Nm�
• Maximum thread length: 7�5mm
►If required: Screw the pressure connection or adapter
M5 to the auxiliary pressure connection (2) and
slightly tighten to avoid damage to the thread:
• Maximum tightening torque: 2�5 Nm�
• Maximum thread length: 7�5mm
5.1 Mounting accessories
The following components can be supplied as accessories: Order no�
Mounting set for DIN rail mounting (DIN rail TH 35-7�5 to EN 60715) E37340
5.2 DIN rail mounting
DIN rail TH 35-7�5 to EN 60715
20
►Fix the mounting clip (1) with the M4 x 35 screws (2) to the flange�
Maximum tightening torque: 0�5 Nm�
►Hook the unit into the DIN rail and clip it into place�
Removal:
►Lever out the mounting clip with a screwdriver at the top or at the bottom and
remove the unit�

8
5.3 Panel mounting
20
►Fix the unit with 2 M4 x 35 screws (1) (not included) to the rear panel�
Maximum tightening torque: 0�5 Nm�
6 Electrical connection
The unit must be connected by a qualified electrician�
The national and international regulations for the installation of electrical
equipment must be adhered to�
Voltage supply to EN 50178, SELV, PELV�
►Disconnect power�
►Connect the unit as follows:
2
1
4
3
L+
L
Out 2
Out 1
2:
4: 3
4
2
1
Pin 1 Ub+
Pin 3 Ub-
Pin 4 (OUT1) Binary switching output pressure monitoring / IO-Link
Pin 2 (OUT2) Analogue output for pressure monitoring

9
UK
7 Operating and display elements
1 2 3 4 5 6 78
10
9
11
Mode/Enter Set
1 to 8: Indicator LEDs
- LED 1 to LED 4 = system pressure / differential pressure in the unit of measurement
which is indicated on the label�
- LEDs 5, 6, 7: not used�
- LED 8 = switching status of the output
9: Alphanumeric display, 4 digits
- Display of the current system pressure�
- Indication of the parameters and parameter values�
10: Set button
- Setting of the parameter values (scrolling by holding pressed; incrementally by pressing
once)�
11: Mode/Enter button
- Selection of the parameters and acknowledgement of the parameter values�

10
8 Menu
8.1 Menu structure
S
M
M
S
M
M
S
M
M
S
M
S
M
M
S
M
M
S
M
M
M
S
M
M
S
M
S
M
M
M
S
M
M
S
RUN
M
M
M
S
M
M
S
M
M
S
M
M
M
S
This manual suits for next models
2
Table of contents
Other IFM Accessories manuals

IFM
IFM UGT204 User manual

IFM
IFM LDL100 User manual

IFM
IFM Efector 200 OGE08 Series User manual

IFM
IFM SBU3 Series User manual

IFM
IFM SBT633 User manual

IFM
IFM OGP7 Series User manual

IFM
IFM Efector 200 OGH2 Series User manual

IFM
IFM SBY2 Series User manual

IFM
IFM PQ78 Series User manual

IFM
IFM O3D300 User manual































