Honeywell DR 4300 Guide

Table of contents

Other Honeywell Measuring Instrument manuals

Honeywell

Honeywell HEN04112 User manual

Honeywell

Honeywell Elster EK280 Instructions for use

Honeywell

Honeywell W8710A User manual

Honeywell

Honeywell VERTEX C User manual

Honeywell

Honeywell DR4300 Series Guide

Honeywell

Honeywell HERMetic UTImeter Gtex Chem IIC Operation manual

Honeywell

Honeywell Enraf 854 ATG User manual

Honeywell

Honeywell E3Point User manual

Honeywell

Honeywell BendixKing KN 62A User manual

Honeywell

Honeywell KA 54 User manual

Honeywell

Honeywell C7355B User manual

Honeywell

Honeywell Themis alpha EI2 Operation and maintenance manual

Honeywell

Honeywell FlexLine SmartServo 954 User manual

Honeywell

Honeywell TE923W - Deluxe Weather Station User manual

Honeywell

Honeywell E-Mon Class 1000 User manual

Honeywell

Honeywell AD1200 User manual

Honeywell

Honeywell SmartLine RMA800 User manual

Honeywell

Honeywell RMA 3000 User manual

Honeywell

Honeywell Vertex Edge User manual

Honeywell

Honeywell Sensepoint XCD RTD User manual

Honeywell

Honeywell Enraf 977 User manual

Honeywell

Honeywell BendixKing KLR 10 User manual

Honeywell

Honeywell Vertex User manual

Honeywell

Honeywell Vertex Edge User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

Form 43-DR-33-74 Page 1 of 3

Model DR 4300

Circular Chart Recorder

Replacement Instruction

Display Module Printed Circuit Assembly (51404459-501)

Document Number Form: 43-DR-33-74

Effective: 3/98

Supersedes: None

Kit Contents This Display Module Printed Circuit Assembly (PCA) Kit contains the

following parts:

•Display PCA

•#6 x 3/8 Plastite Screws (2)

•Cables (2)

Summary Enclosed are a new display module PCA and parts for your DR4300

recorder. Use the following procedure to install the new display module.

WARNING Never access components inside the case with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 43-DR-33-74

Component Location Refer to Figure 1 for the component locations and Table 1 for the

installation procedure.

24229

Screws

Display

ModulePCA

Cable

Pen 2

Cable

Pen 1

Figure 1 – Component Location

Kit Instruction, continued

Form 44-DR-33-74 Page 3 of 3

Installation Procedure Follow the procedure in Table 1 to install the new display module PCA in

your recorder.

Table 1 – Display Module Printed Circuit Assembly Installation

Step Action

1Power down the recorder. Open the chart door and swing the chart

plate out.

2 Note cable orientation before removing the two screws holding the

display module PCA to the top of the case.

3 Disconnect cable(s) from the back side of old PCA. Pull outward

on the connector’s end tabs then pull out the ribbon cable(s).

You can leave the cable(s) attached to J4 on the main PCA(s)

unless you are also replacing the cable. If you are replacing the

cable(s), disconnect each one from J4 on its specific PCA and

remove it, noting the routing layout.

4 Install the cable(s) on the new display PCA. Insert the cable in the

connector and push in on end of connector tabs to lock cable(s) in

place.

If you are replacing the cable(s), go to Step 5.

If you are using the existing cable(s), go to Step 6.

5 Feed the pen 1 ribbon cable behind the transmitter power

assembly, behind the Main PCA for pen 1 (right side of case) to its

J4 connector (upper right corner).

If applicable, run the pen 2 ribbon cable behind the transmitter

power assembly, behind the pen 1 Main PCA, bringing it to the J4

connector on the Main PCA for pen 2 (left side of case). This

ribbon should be on top of the pen 1 ribbon cable.

6 Secure the new display PCA to the case with the screws provided.

7 Close the chart plate and apply power. Check for normal display

indication.