Honeywell MP909E Datasheet

INSTALLATION INSTRUCTIONS

MP909E

UL Listed Damper Actuator

BEFORE INSTALLATION

The MP909E UL Listed Pneumatic Damper Actuator is used

for control of Leakage Rated (Smoke) Dampers, classified

under Underwriters Laboratories Standard 555S, for use in

smoke control systems.The MP909 is a piston-type, rolling-

diaphragm operated actuator and can be mounted in any

position and installed either externally or internally.

The UL listing of the actuator and the damper classification

apply only when Listed Honeywell Actuators are installed on

Honeywell D640SD, D641SD, D644SD, or D645SD Series

Dampers as specified in the installation instructions shipped

with the devices.

All installations must also comply with the requirements of

NFPA 90A, National Fire Protection Standard for the

Installation of Air Conditioning Systems.

Table 1 lists the only MP909 Actuators approved for use with

UL Classified Leakage Rated (Smoke) Dampers.

Table 1. Damper Actuators for Leakage Rated Dampers.

Actuator

Model Spring Range

psi (kPa) Mounting Bracket

MP909E1422 5-10 (34-69) Internal/

Normally

Open

Trunnion

MP909E1414 5-10 (34-69) Internal/

Normally

Closed

Trunnion

MP909E1034 5-10 (34-69) External 90°Fixed

MP909E1364 5-10 (34-69) External Trunnion

Mainline pressure limits:

— 15 psi minimum

— 25 psi maximum

Tools needed:

1. 7/16-inch box end wrench

2. 1/8-inch Allen wrench

3. Squeeze bulb

INSTALLATION

External Mounting

1For external mounting dimensions, see Figure 1.

2Check faceplate position (Fig. 2).Adjust faceplate

position if necessary.

3Determine the damper drive axle direction of rotation to

the normal position (position with 0 psi applied to

actuator).

4Rotate damper drive axle to normal position.

5Locate proper shaft hole (Fig. 3) over damper shaft.

Arrow on bracket surrounding hole should match

rotation determined in Step 3.

6Position mounting bracket.

7Secure mounting bracket. Use four of the 10 holes

available in bracket and drill screws provided.

8To provide close-off force, use a squeeze bulb and

stroke the actuator:

a. For normally open dampers, fully extend actuator

shaft then retract 1/2-inch (13 mm).

b. For normally closed dampers, extend actuator

shaft 1/2-inch (13 mm).

CAUTION

See Figure 4 for proper tightening of crankarm bolts.

9Go to PIPING section.

Internal Mounting

Normally Closed

1For normally closed internal mounting dimensions, see

Figure 5.

2Check faceplate position (Fig. 6).Adjust faceplate

position if necessary.

3Use a 1/8-inch Allen wrench to loosen mounting set

screws on damper mounting clamp (Fig. 6) one turn.

Remove and discard shipping stop.

4Locate factory-installed drive ear on damper. (Mounted

per Damper Ordering Instructions.) Actuators must be

mounted only in this (these) position(s)

95-6076

11-95 UL

MP909E UL LISTED DAMPER ACTUATOR

95-6076 2

(430)

1-1/8 (30) CLEARANCE

MP909E

1-1/2

(39)

1-1/2

(39)

6-7/8

(175)

5-3/4

(145)

AXLE

ROTATION TO

NORMAL

C8092

Fig 1. External Mounting Dimensions in Inches (Millimeters).

FACEPLATE

MOUNTING

BRACKET

C8209

90°

AXLE

ROTATION TO

NORMAL

MOUNTING HOLES

C8208

CRANKARM

CLEVIS PIN LOCATION ON

3.1-INCH STROKE OPERATORS

(FACTORY INSTALLED)

1-3/8(35)

REF.

1-5/8 INCH (41 MM) FOR 3.1 INCH STROKE

OPERATORS AND N.C. DAMPERS

Fig. 2. External Mounting Faceplate Positioning.

Fig. 3. External Installation.

5Remove mounting screw from damper end of truss link.

Loosen screw between base and truss link. Remove

clevis pin from damper end of actuator pushrod.

6Set actuator in place by hooking actuator mounting

clamp over bottom edge of damper frame.

7Set damper to the normal (closed) position.

8Insert clevis pin in drive ear hole marked P and the

pushrod hole nearest the actuator.

9Connect truss link to damper and tighten both truss link

screws.

JTighten damper mounting screws.

KGo to PIPING section.

MP909E UL LISTED DAMPER ACTUATOR

95-6076

1. BOLTS ARE TIGHTENED TO MORE THAN 90 LB-IN

BUT LESS THAN 200 LB-IN.

2. TIGHTEN BOTH BOLTS (WITH 7/16 BOX END

WRENCH IF AVAILABLE).

3. TIGHTEN EACH BOLT AGAIN TO THE REQUIRED

TORQUE.

C8211

CRANKARM BOLTS

Fig. 4. Crankarm Bolt Tightening.

Fig. 5. Internally Mounted Normally Closed Mounting Dimensions in Inches (Millimeters).

3/8 (10) CLEARANCE

(430)

EDGE OF

DAMPER

6-3/8

(160)

C8210

FACEPLATE PARALLEL

TO BACK EDGE OF

MOUNTING BRACKET

C8212

TRUSS

LINK TRUSS LINK

MOUNTING

SCREW 1

FACEPLATE

PIVOT PLATE

PUSHROD

1-13/32 INCH (36 MM) REF.

DAMPER

DRIVE EAR

E HOLE

CLEVIS PIN

(P HOLE)

DAMPER

MOUNTING

CLAMP

SHIPPING

STOP

SETSCREWS MOUNTING

BRACKET

PUSHROD

DAMPER

DRIVE EAR

CLEVIS PIN

(P HOLE)

DETAIL A

TOP VIEW

CLIP

Fig. 6. Internal Mounting Normally Closed Damper.

MP909E UL LISTED DAMPER ACTUATOR

95-6076 4

Normally Open

1For internal mounting dimensions, see Figure 7.

2Check faceplate position (Fig. 6). Adjust faceplate

position if necessary.

3Use 1/8-inch Allen wrench to loosen set screws on

mounting clamp (Fig. 6) one turn. Remove and discard

shipping stop.

4Determine height of damper drive blade. Dampers

with 10, 12, 18, 26, 34, and 42-inch B dimensions

have 8-inch drive blades. All others have 6-inch drive

blades.

5For installation with 6-inch drive blades, go to Step 6.

For installation with 8-inch drive blades, remove clevis

pin A (Fig. 8) and reinstall in pushrod hole marked 8.

(Hole in crankarm marked 90.)

6Locate factory installed drive ear on damper. (Mounted

per Damper Ordering Instructions.) Actuators must be

mounted only in this (these) position(s).

7Loosen truss link to actuator base mounting screw.

Remove clevis pin C from damper pushrod.

8Set actuator in place by hooking mounting clamp over

bottom edge of damper frame.

9Connect damper pushrod to damper drive ear with

clevis pin.

JTighten set screws on mounting clamp.

KConnect truss link to damper and tighten both truss link

screws.Truss link must be bent slightly.

(430)

EDGE OF

DAMPER

6-1/2

(165)

C8213

MP909E

Fig. 7. Internal Mounting Normally Open Dimensions in Inches (Millimeters).

C8214

1REFERENCE DIMENSIONS:

4-INCH STROKE (FACTORY

SET) = 3-3/16 INCH (81 MM)

CLEVIS

PIN C

CLEVIS PIN B

(FACTORY INSTALLED)

DAMPER

PUSHROD

CLEVIS PIN "A" LOCATION

FOR 8-INCH DRIVE BLADE

CLEVIS PIN "A" LOCATION

FOR 6-INCH DRIVE BLADE

(FACTORY INSTALLED)

Fig. 8. Internal Mounting Normally Open Installation.

Piping

Special piping is required for Leakage Rated (Smoke)

Damper actuators.The piping from the actuator to the device

which interfaces to the smoke control system must be 1/4-inch

copper tubing or as required by local code. 1/4-inch polyester

tubing pigtails are provided with the actuator to interface with

the copper tubing.

Figure 9 shows how to adapt 1/4-inch copper tubing to

polyester tubing. CCT1635B compression adapters connect

the 1/4-inch copper tubing to the 1/4-inch polyester.These

adapters must be ordered separately.

Copper tubing can be connected directly to the actuator as

shown in Figures 10 and 11.

MP909E UL LISTED DAMPER ACTUATOR

95-6076

CCT 1635B

COMPRESSION

ADAPTER

1/4 IN.

POLYESTER

TUBING

1/4 IN.

BARBED

FITTING

ACTUATOR

C8216

Fig. 9.Transition Piping for 1/4-Inch PolyesterTubing to

1/4-Inch CopperTubing.

NOTE: For actuators using the trunnion mounting bracket,

leave enough tubing free of rigid supports to allow

the actuator to swivel on the trunnion bracket without

flexing the copper tubing (Fig.11).

CCT 1421

REPLACE BRASS

FERRULE WITH

RED FERRULE (CCT1574)

(NOTE ORIENTATION)

REPLACE BRASS

FERRULE

1/4 IN.

BARBED

FITTING

ACTUATOR

C8217

CONTROLLER

NUT NUT 1/4 IN.

COPPER

TUBING

Fig. 10.Transition Piping for 1/4-Inch Barbed Fitting to 1/4-Inch CopperTubing.

C8215

DAMPER

FRAME

DUCT FLOOR

1/4 IN COPPER

TUBING MP909E

ACTUATOR

Fig. 11. Routing CopperTubing NearTrunnion Pivot.

Multiple Actuators

Multiple actuators must be piped so the Smoke Control

System operates all sections of multisection dampers

simultaneously.

Pipe multiple MP909E actuators in parallel (Fig. 12).

MP909E

C1468

TO SMOKE

CONTROL

Fig. 12. MP909E Parallel Installation.

MP909E UL LISTED DAMPER ACTUATOR

95-6076 6

Helping You Control Your World

Home and Building Control

Honeywell Limited-Honeywell Limitée

155 Gordon Baker Road

North York, Ontario

M2H 2C9

95-6076 1-96 Printed in U.S.A.

Home and Building Control

Honeywell Inc.

Honeywell Plaza

P.O. Box 524

Minneapolis, MN 55408-0524

Table of contents

Other Honeywell Controllers manuals

Honeywell

Honeywell Excel 10 User manual

Honeywell

Honeywell AQS51-KAM Operation manual

Honeywell

Honeywell WEB-300E Series User manual

Honeywell

Honeywell TheraPro HR90 User manual

Honeywell

Honeywell VU443A Operation manual

Honeywell

Honeywell ML6425 Series Operation manual

Honeywell

Honeywell Touchpoint 1 User manual

Honeywell

Honeywell N20010 User manual

Honeywell

Honeywell McDonald's HEMS II User manual

Honeywell

Honeywell HC900 User manual

Honeywell

Honeywell DCP552 Mark II User manual

Honeywell

Honeywell Excel 15 W7760A User manual

Honeywell

Honeywell ML6275 Operation manual

Honeywell

Honeywell 1000 Series User manual

Honeywell

Honeywell D6 PRO User manual

Honeywell

Honeywell ALERTON VIP-363-HOA User manual

Honeywell

Honeywell Ex-Or MSM2000D Installation and operation manual

Honeywell

Honeywell S4965V3250 Operating and installation instructions

Honeywell

Honeywell ML6194 Operation manual

Honeywell

Honeywell Scan Dome ll HTX-2500 Owner's manual

Honeywell

Honeywell Satronic DVI 980 User manual

Honeywell

Honeywell MP953A Operation manual

Honeywell

Honeywell LYNX Touch Series User manual

Honeywell

Honeywell IAQ Poin User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual