Honeywell ICON 100 SERIES User manual

EN1B-0004UK07 R1003

ICON-111S / ICON-111SR / ICON-112S

ICON-112SR / ICON-132S / ICON-132SR

ICON 100 SERIES REFRIGERATION CONTROLLER

INSTALLATION GUIDE

ICON 100 SERIES INSTALLATION GUIDE

Trademark Information:

Genus

is a registered trademark of Honeywell Control Systems Ltd.

EN1B-0004UK07 R1003 1

ICON 100 SERIES INSTALLATION GUIDE

CONTENTS

CONTENTS................................................................................................................................. 2

1. SAFETY INSTRUCTIONS.......................................................................................................3

2. GENERAL DESCRIPTION...................................................................................................... 6

3. TECHNICAL SPECIFICATION...............................................................................................9

4. INSTALLATION................................................................................................................... 12

4.1 Introduction ................................................................................................................... 12

4.2 Thermistor Probe........................................................................................................... 12

4.3 Defrost Termination Probe............................................................................................ 12

4.4 Electrical Wiring............................................................................................................. 13

4.5 Applications in Critical Environments.............................................................................13

4.6 Fitting............................................................................................................................14

4.7 Connections.................................................................................................................. 15

For Icon 100 series operating instructions, please refer to document:

MU2B-0001UK07. This can be found at Honeywell Cooling & Refrigeration’s

internet site: www.honeywell.com/cooling

EN1B-0004UK07 R1003

ICON 100 SERIES INSTALLATION GUIDE

1. SAFETY INSTRUCTIONS

A. Keep this instruction booklet where it can always be easily consulted

by the operator or by maintenance personnel.

B. Warning: hot components may be inside the plastic housing of the

controller.

C. No user-serviceable parts are inside the plastic housing of the

controller.

D. The controller and any device connected to it must be installed in

compliance with the Safety Regulations in force. If these regulations

are not respected during installation, and if our product is not installed

in compliance with the indications given in this instruction booklet, then

this may cause a reduction in the safety level of the controller. In

particular, the ambient operating conditions for the controller given in

our technical data must be complied by; absolutely avoid: water

condensation or excessive humidity, exposure to steam, corrosive - or

toxic gases, contact with any type of liquid, and exposure to shocks or

to extreme vibrations. Not respecting the above indications could

cause malfunctions and entail unpredictable consequences, e.g., in the

worst cases, dangerous electrical discharges on probes or other parts

of the instrument.

EN1B-0004UK07 R1003 3

ICON 100 SERIES INSTALLATION GUIDE

E. This controller is guaranteed by Honeywell to have a specific immunity

level, in compliance with CE regulations, against irradiated and

conducted electromagnetic disturbances. By irradiated electromagnetic

disturbances we recommend to screen the controller with a metal

screen connected to ground. To eliminate, or at least reduce

conducted disturbances, which not only could propagate through the

mains but also through the probes or the connected loads, carry out

the electrical wiring according to the indications given in this instruction

booklet. If necessary, use filters with suitable characteristics for specific

applications and for the detected type of disturbance.

F. If the type of probe to be used will directly touch foodstuffs, make sure

that it is in compliance with the local sanitary and health regulations.

G. The controller has no type of protection for the connected loads, so

these must be protected against short circuits, over-current or over-

voltage, excessive temperature, etc., by suitable protective means

(such as fuses, suitable thermo-magnetic circuit breakers, thermal

protections, etc.). At any rate, the electrical power lines that supply

both the controller and any other device connected to it, either directly

or through a transformer, must be manufactured in compliance with the

regulations in force.

EN1B-0004UK07 R1003

ICON 100 SERIES INSTALLATION GUIDE

H. When the controller is used in appliances where any malfunction of

said controller could cause a form of risk to persons, animals or things,

it is ABSOLUTELY MANDATORY to provide a suitable

protective/safety device, in addition to the controller, which

independently starts to operate in case of a failure.

I. The controller cannot be used as a critical component in life-support

devices or systems without a written approval expressly issued by the

legal representative of Honeywell.

CAUTION

Disconnect the power supply before you begin installing the Icon controller.

Do not reconnect the power supply until you have completed installation.

EN1B-0004UK07 R1003 5

ICON 100 SERIES INSTALLATION GUIDE

2. GENERAL DESCRIPTION

The microprocessor-based electronic Honeywell Icon 100 Series

Refrigeration Controllers are designed to measure, display, and control the

temperature of refrigeration cases and coldrooms. The Icon 100 Series are

(thermostat and / or defrost probes), and has up to three relay outputs

(compressor, defrost and fan).

All of the controllers operating parameters are configurable using a four

button keypad on the front of the temperature display. Access to the

configuration parameters menu is achieved through the front panel

keyboard by following a very simple security procedure, after which the

required parameter values can be set quickly and easily.

A Honeywell NTC 2k Ohm probe is supplied as standard with Icon and has

a measuring range of –50 to +90

C. (-58 to +194

F), that can be installed

up to 10 meters (30ft) from the controller without requiring instrument

recalibration. Icon can also use the PT1000 thermistor probe with a

measuring range of –50 to +90

C. (-58 to +194

F). Please note that you

cannot have a combination of NTC or PT1000 probes on a single controller.

All programming data is stored in a non-volatile memory (EEPROM), where

it also remains during a power failure.

EN1B-0004UK07 R1003

ICON 100 SERIES INSTALLATION GUIDE

The Icon 100 Series have the following features.

• display the measured case temperature as well as the alarm

messages that refer to faulty cooling/refrigeration plant functions.

• control the measured temperature through the thermostat probe in

order to maintain it under a set limit value (main set point +

differential), by activating the compressor to lower said temperature

every time it exceeds the main set point + differential value.

• control the defrost cycles of the cooling/refrigeration plant manually or

through the programmed mode; in the latter mode it is possible to set

the times of up to four daily defrost cycles (112SR & 132SR models

only)

• control the defrost cycle time as well as the successive startup of the

cooling/refrigeration plant fan through the defrost probe. (112SR &

132SR models only)

• Honeywell Genus

Network compatible.

• Optional Genus

comms. Module.

EN1B-0004UK07 R1003 7

ICON 100 SERIES INSTALLATION GUIDE

Product Description Part-No

Icon 111S 1 relay, 1 probe. ICON-111S

Icon 111SR 1 relay, 1 probe, real-time clock. ICON-111SR

Icon 112S 1 relay, 2 probes. ICON-112S

Icon 112SR 1 relay, 2 probes, real-time clock. ICON-112SR

Icon 132S 3 relays, 2 probes. ICON-132S

Icon 132SR 3 relays, 2 probes, real-time clock. ICON-132SR

Icon HotKey Programmable HotKey for Icon 100

Series.

ICON-KEY1

Icon Comms

Module

Honeywell Genus® communications

module for Icon 100 Series.

ICON-COMMS

Temperature

Probe

2k NTC temperature probe with 7m

cable.

TP002K

Temperature

Probe

PT1000 temperature probe with 7m

cable.

TPPT1K

Table 1. Icon Part Numbers & Descriptions

EN1B-0004UK07 R1003

ICON 100 SERIES INSTALLATION GUIDE

3. TECHNICAL SPECIFICATION

Part Number

ICON-111S

ICON-111SR

ICON-112S

ICON-112SR

ICON-132S

ICON-132SR

Housin

Self extin

uishin

PC/ABS zzzzzz

Power Su

AC 230Vac ~ 4VA 50/60 Hz zzzzzz

Dis

3 di

its, 14.2 mm hi

reen LED's zzzzzz

Resolution

0.1

C or one unit zzzzzz

Accurac

± 0.7% t.s. zzzzzz

Probe T

2 x thermistor PT1000 / 2k NTC zzzz

1 x thermistor PT1000 / 2k NTC zz

Table 2. Technical Specification

EN1B-0004UK07 R1003 9

Other manuals for ICON 100 SERIES

This manual suits for next models

Table of contents

Other Honeywell Controllers manuals

Honeywell

Honeywell MSR PolyGard 2 MGC2-K User manual

Honeywell

Honeywell R7426A User manual

Honeywell

Honeywell HCU 23 User manual

Honeywell

Honeywell T775A User manual

Honeywell

Honeywell H46C User manual

Honeywell

Honeywell Centra Line EAGLE Installation and operation manual

Honeywell

Honeywell SP10K User manual

Honeywell

Honeywell MIWI350 Operating instructions

Honeywell

Honeywell UDC 2300 User manual

Honeywell

Honeywell CIPer 50 Installation and operation manual

Honeywell

Honeywell CP-UL1012S User manual

Honeywell

Honeywell T6590A User manual

Honeywell

Honeywell VB6 Series User manual

Honeywell

Honeywell Touchpoint Plus User manual

Honeywell

Honeywell ML7999C Operation manual

Honeywell

Honeywell DBC2000 Series User manual

Honeywell

Honeywell HON 380 Instruction Manual

Honeywell

Honeywell S8701 User manual

Honeywell

Honeywell D6 PRO User manual

Honeywell

Honeywell 1000 Series User manual

Honeywell

Honeywell ML6174 Series User manual

Honeywell

Honeywell N20010 User manual

Honeywell

Honeywell S9361A207 Series User manual

Honeywell

Honeywell Aquastat L4006A User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual