Hioki 7015 User manual
SIGNAL SOURCE
OPERATION GUIDE
7015
1
――――――――――――――――――――――――――
―――――――――――――――――――――――
SOURCE FUNCTIONS
1. source DCCV function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV
(3) Press SHIFT to source standby mode
(4) Press MODE proper times to select 1.5V range or 15V
range
(5) Press or to select digit adjustment
(6) Press ▲or ▼to set the value of digit
(7) Press OUTPUT to output DCCV source
2. source DCCC function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CC
(3) Press SHIFT to source standby mode
(4) Press or to select digit adjustment
(5) Press ▲or ▼to set the value of digit
(6) Press OUTPUT to output DCCC source
3. source SCAN DCCV(DCCC) CONTINUOUS
function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select CONTINUE
(6) Press OUTPUT to output DCCV(DCCC) source
2
――――――――――――――――――――――――――
―――――――――――――――――――――――
4. source SCAN DCCV(DCCC) CYCLE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select CYCLE
(6) Press OUTPUT to output DCCV(DCCC) source
5. source SCAN DCCV(DCCC) STEP function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select STEP
(6) Press OUTPUT to output DCCV(DCCC) source
(7) Press ▲or ▼to change STEP output
3
――――――――――――――――――――――――――
―――――――――――――――――――――――
6. source SCAN DCCV(DCCC) output
adjustment
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press MODE again and hold 1 second
(6) Press MODE to cycle through STEP, TIME
INTERVAL and AMPLITUDE adjustments
(7) Press ▲or ▼to adjust STEP from 1 to 16 and
TIME INTERVAL from 0 to 99
(8) Press OUTPUT to save your setting
(9) Press MODE again and hold 1 second
7. source RAMP DCCV(DCCC) CONTINUOUS
function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press proper times to select CONTINUE
(6) Press OUTPUT to output DCCV(DCCC) source
4
――――――――――――――――――――――――――
―――――――――――――――――――――――
8. source RAMP DCCV(DCCC) CYCLE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press proper times to select CYCLE
(6) Press OUTPUT to output DCCV(DCCC) source
9. source RAMP DCCV(DCCC) output
adjustment
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press MODE again and hold for 1 second
(6) Press MODE to cycle through POSITION,
RESOLUTION and AMPLITUDE adjustments
(7) Press ▲or ▼to adjust the RESOLUTION from 1 to
999
(8) Press OUTPUT to save your setting
(9) Press MODE again and hold 1 second
5
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
10. source PULSE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to PULSE
(3) Press SHIFT to source standby mode
(4) Press ▲or ▼to select FREQUENCY
(5) Press MODE to display DUTY CYCLE
(6) Press ▲or ▼to adjust the DUTY CYCLE
(7) Press MODE to display PULSE WIDTH
(8) Press ▲or ▼to adjust the PULSE WIDTH
(9) Press MODE to display AMPLITUDE
(10) Press ▲or ▼to select the AMPLITUDE
(11) Press OUTPUT to output PULSE source
･Set SLIDE SWITCH to M/S position for source
functions
･The inside CIRCLE(FUNCTION) SWITCH labels
are for measurement functions
･The outside CIRCLE(FUNCTION) SWITCH labels
are for source functions
6
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
±1.5V ±15V SCAN
±1.5V
SCAN
±15V
SCAN
±1.5V
SCAN
±15V
±25mA SCAN
±25mA
SCAN
±25mA
Hz %ms Level
･In case FUNCTION SWITCH is at CV, Press
MODE to cycle through DCCV 1.5V range, DCCV
15V range, SCAN DCCV 1.5 range, SCAN DCCV
15V range, RAMP SCAN DCCV 1.5V range and
RAMP SCAN DCCV 15V range
･In case FUNCTION SWITCH is at CC, Press MODE to
cycle through DCCC 25mA range, SCAN DCCC 25mA
range and RAMP SCAN DCCC 25mA range
･In case FUNCTION SWITCH is at PULSE, Press
MODE to cycle through FREQUENCY(Hz),
DUTY CYCLE(%), PULSE WIDTH(ms) and
AMPLITUDE(V)
7
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
INTERVAL TIMESTEP AMPLITUDE
STEPS of
RESOLUTION
START
POSITION
START
AMPLITUDE(V)
STEPS of
RESOLUTION
END
POSITION
END
AMPLITUDE(V)
▲
▼
･In case source SCAN DCCV(DCCC) output
adjustment, Press MODE to cycle through
STEP(address), INTERVAL TIME(s) and
AMPLITUDE(V)
･In case source RAMP SCAN DCCV(DCCC) output
adjustment, Press MODE to cycle through START
POSITION, STEPS of RESOLUTION and START
AMPLITUDE(V)
In case you want to change END menu, Press ▲or ▼at
START POSITION then you can set STEPS of
RESOLUTION and END AMPLITUDE(V)
8
――――――――――――――――――――――――――
―――――――――――――――――――――――
MEASUREMENT FUNCTION
1. measurement DCV(ACV, ACDCV) function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to V or mV
(3) Press AC/DC to select DCV(ACV, ACDCV)
measurement
2. measurement DCA(ACA, ACDCA) function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to mA
(3) Press AC/DC to select DCA(ACA, ACDCA)
measurement
3. measurement OHM function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to Ω
(3) Press AC/DC for CONTINUITY
4. measurement TEMPERATURE function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to mV
(3) Press REL (TEMP) and hold for 1 second to display
temperature
(4) Press DUAL to swap ℃and display
Table of contents
Other Hioki Measuring Instrument manuals
Hioki
Hioki 3275 User manual
Hioki
Hioki SAFETY HiTESTER 3258 Instruction manual
Hioki
Hioki PQ3100 User manual
Hioki
Hioki PW3360-21 User manual
Hioki
Hioki 3196 Instruction manual
Hioki
Hioki TM6102 Use and care manual
Hioki
Hioki 3470 User manual
Hioki
Hioki RM3545 User manual
Hioki
Hioki BT4560 User manual
Hioki
Hioki MR8740T Instruction manual
Hioki
Hioki CM3289 User manual
Hioki
Hioki CM4141 User manual
Hioki
Hioki 3664 User manual
Hioki
Hioki HiTester 3443-01 User manual
Hioki
Hioki 3126-01 User manual
Hioki
Hioki 3280-10F User manual
Hioki
Hioki IM3523 User manual
Hioki
Hioki 9651 User manual
Hioki
Hioki CM4141-50 User manual
Hioki
Hioki CT6710 User manual
