HeroCamper BM500 User manual
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
Smart battery monitor kit to fit the Hero Camper. It enables you
to see charge and discharge regardless of which battery you have
installed. The information is shown on display and can be shown
on the app as well.
B A T T E R Y M O N I T O R K I T
C O M P O N E N T S A N D D I M E N S I O N S
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
W i r e D i a g r a m
-Please note this is only for installation in Hero Camper. If the product in not for a Hero Camper we refer to
the original manual of each product.
T O O L S F O R I N S T A L L A T I O N
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
I N S T A L A T I O N G U I D E
Please note this is only an example for Hero Camper. There can be some models that
have diffrient electrical installation setup. Refer to the installation diagram above as
guideline. If the product in not for a Hero Camper we refer to the original manual of
the manufactor for each product.
1) Pull down the seat inside the Hero Camper.
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
3) Use leveller to position the BM500. Mark the 3 holes with a pencil. Remove the
BM500 and use an ø2mm drill. Attach the BM500 with the provided PH 20x3mm
screws. Use vaccuum to remove any leftovers.
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
4) Use leveller to position the Display holder. Mark the 4 holes with a pencil.
Remove the Display holder and use an ø2mm drill. Attach the Display holder
with preffered screws. Use vaccuum to remove any leftovers.
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
5) Remove the plastic cover for screw holes gently by hand on the Display.
6) We recommend inserting the communication cable into the display before fully
mounting the display to the holder (see step 7). Mount the display into the installed
display holder and gently assemble it with the provided PH 10x2mm screws. Be
careful not to overtighten. Re-mount the plastic cover afterwards.
#HeroCamper™–www.herocamper.com
Lammefjordsvej 5 –6715 Esbjerg N –Denmark
Phone +45 7022 5840 –sales@herocamper.com
VAT No DK –40193189
Version 07-02-2023
8) Start with unscrewing the safety plate for the BM500 by hand. Then remove the nut,
spring washer and washer. If you can not do it by hand, use a M16 wrench.
9) Remove the negative system ground cable and connect it to the BM500 S- port. Use a
M16 wrench to tighten.
Table of contents
