Hardy Barth ECB1-LR Quick guide

Smartmeter

eCB1-LR

Conﬁguraon instrucons

Configuration instructions eCB1

smartmeter

Version: 1.2.3

English

Table of contents

Contact data...............................................................................................................3

General infomaon about the eCB1............................................................................4

Note.................................................................................................................................................4

Meaning of the LED states...............................................................................................................4

Reset funkon..................................................................................................................................4

Setup of direct LAN connecon to the eCB1...............................................................4

Connecng the BUS connecon between wallbox and eCB1......................................7

Conﬁguraon of the eCB1 LR MP+ (metering point)...................................................8

Open the Webinterface...................................................................................................................8

Language und region.......................................................................................................................9

Date und  e..................................................................................................................................9

Network se"ngs............................................................................................................................10

Internal...........................................................................................................................................11

Charge connector 1........................................................................................................................12

Finish setup....................................................................................................................................12

Explanaon of the web interface (PV load control)...................................................14

Conﬁguraon of the eCB1 LR PV (PV load control)....................................................15

Language und region.....................................................................................................................15

Date und  e................................................................................................................................16

Network se"ngs............................................................................................................................17

House connecon..........................................................................................................................18

Charge connector 1........................................................................................................................20

Setup co pleon...........................................................................................................................22

Fir ware update............................................................................................................................23

I portant se"ngs for operaon...................................................................................................23

Charge-Log.....................................................................................................................................26

Warranty / Guarantee...............................................................................................28

Guarantee speciﬁcaons and warranty.........................................................................................28

Notes........................................................................................................................30

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Contact data

manufacturer: eCHARGE Hardy Barth GmbH

Leinbergstraße 14

92262 Birgland-Schwend

telephone: +49 9666 188 13 0

telefax: +49 9666 188 13 1

web: www.echarge.de

mail: support@echarge.de

Configuration instructions eCB1

smartmeter

Version: 1.2.3

General infomation about the eCB1

Note

To prevent confusion between the different models, please refer to the version of the

device marked on the packeging. The installation and configuration should be carried

out in the specified order.

Meaning of the LED states

Status-LED

•

permanent green The eCB1 is ready for operation.

•

Slowly flashing in green The device starts.

•

Quickly flashing in green A firmware update is running.

•

glowing or flashing in red or An error occured.

orange

Network-LED

•

Off no connection

•

permanent green connection active

•

green flashing network activity

Bus-LED

•

Off device is not configured

•

green connection is ok

•

orange no device detected

•

red BUS error

Reset funktion

You can reset the eCB1 to network settings or simply restart the device by pressing the

reset button. The time period of pressure applied is important.

Reset to factory settings

With a pointy ob ect, press the reset button for 4 to 10 seconds.

Restart the eCB1

To restart, use a pointy ob ect to press the reset button for 1 to 3 seconds.

Setup of direct LAN connection to the eCB1

Configuration instructions eCB1

smartmeter

Version 1.2.3

Step 1: Install the eCB1 and connect it to the power supply.

Step 2: Connect the eCB1 to your network, a PC or laptop using a LAN cable see

diagram).

Please note: Make sure that only one unconfigured eCB1 is connected in your network to

avoid name collisions.

1. Start your browser

2. Type in the following URL „http://ecb1.local“ see image below).

→ The user interface of the eCB1 opens.

If the user interface does not open, please check the following points:

1. Name resolution does not work

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Connect the eCB1 to your

network using a LAN cable

and insert it into the LAN

port of the eCB1.

Connect your PC/laptop with

your network/router by

inserting the LAN cable into

the LAN port.

Access the user interface using the current IP address of the eCB1.

„(http://<IP>/)“

To do this, ca up the router´s user interface and read the IP address of the eCB1 (see

manua of your router).

If you have Windows XP/7/8: insta App e Bonjour® . You can find the donw oad ink on

www.app e.com. Then enter the URL again.

Note: App e Bonjour® is a so inc uded in App e iTunes®.

A ternative y contact the network administrator.

2. The status LED does not glow

If the status LED of the eCB1 does not g ow, it means that

the smartmeter is not provided with any power.

P ease make sure that at east one of the phase conductos

L1 and the neutra conductor N are connected to the eCB1.

3. The status LED glows or blinks red

If the status LED g ows or b inks red, an error has occured.

P ease restart the eCB1 by pressing the reset button

with a pointy objet for about to 3

seconds.

4. The Network-LED does not glow

If the network-LED does not g ow, the network cab e is not proper y/correct y connected to

the network port. P ease make sure that you have inserted both ends of the cab e proper y

and correct y.

5. eCB could not be found in the network

In this case the eCB1 is not ocated in the same oca network. P ease connect the

eCB1 with the same Router/Switch as the one of your PC’s/ aptop’s.

If that does not so ve your prob em, p ease reset the eCB1 to its factory settings by

pressing the reset button with a pointy object for about 4 to 0 seconds.

Configuration instructions eCB

smartmeter

Version: 1.2.3

Connecting the BUS-connection between wallbox

and eCB1

Image 1: shows the BUS-clamps of the cPµ1.

Image 2: shows the BUS-clamps of the eCB1.

(Please note the green marks in Image )

hese have to be connected as follows:

- Plug the brown wire (second slot on the eCB1) in

„1“ (shown in Image 1).

- Plug the black wire (third slot on the eCB1) in

„2“.

- Last step you plug the blue wire (first slot on the

eCB1) in „3“.

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Configuration of the eCB1 LR MP+ (metering

point)

Open the Webinterface

Open the Webinterface of the eCB1 MP+ (metering point at the house connection) by

entering its IP address in your webbrowser

Prior to that, it has to be integrated into the network of the house Then through the

interface of the router, you can find the IP address of all eCB1, including this one

If therer is no other configured eCB1 in your Network you can contact the eCB1 MP+ with

http://ecb1 local for first configuration

If the Domane Name System does not work you can find the IP adress through the

Webinterface of your router

The following page should open up:

Please click “proceed” to get to the following section:

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Language und region

Here you can set:

–the language

–the country in which you are installing the charging station and

–the time zone

Date und time

Click “proceed” to get the following screen:

Here you can set the time and date manually or automatically.

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Manual setting

Click on the date button and select the desired date from the calendar. Then click the

time button and enter the current time.

Please separate the hours, minutes and seconds with colons.

To complete the settings, press “Set time” and the settings will be saved.

Automatic setting

In this case “Date” and “Time” do not need an entries.

There are pre-set internet pages in section “NTP Server 1” and “NTP Server 2”. These will

connect ou automaticall with a time server.

Click on “Set time by ntp” to save our settings.

If ou want to connect with a different, or our own time server, please enter the internet

address manuall .

B clicking “automatic synchronise at boot”, the time will be s nchronised automaticall

after ever outage (power, network, etc.).

After completion of the time and date settings, click on “proceed” to get to the next

section.

Network settings

If ou choose “DHCP” as protocol:

Your DHCP-Server (e. g. router) will do

further settings automaticall and fill the

remaining blank spaces.

There are no other settings to be made in

the section except selecting a hostname.

Please select a distinct host name.

The device should respond to the given

hostnamen (givenname.local). Upon deliver

the hostname given is „ecb1 local“.

Configuration instructions eCB1

smartmeter

Version: 1.2.3

Other manuals for eCB1-LR

Table of contents

Other Hardy Barth Measuring Instrument manuals

Hardy Barth

Hardy Barth eCB1-LR Instruction sheet

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

Hardy Barth eCB1-LR Quick guide

Popular Measuring Instrument manuals by other brands