Harbor Breeze HTD20005 User manual

ITEM #2599777

MODEL #HTD20005

KENTON CEILING FAN

Harbor Breeze®is a registered trademark

Español p. 18

Questions, problems, missing parts?

Before returning to your retailer, call our customer

service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

VR20245

TABLE OF CONTENTS

Preparation .......................................................................................................................

Initial Installation Instructions ...........................................................................................

Wiring Instructions ............................................................................................................

Final Installation Instructions ............................................................................................

Operation Instructions ......................................................................................................

Care and Maintenance .....................................................................................................

Troubleshooting ...............................................................................................................

Limited Lifetime Warranty ...............................................................................................

FCC Warning ……………..................................................................................................

Safety Information ............................................................................................................ 4

Package Contents ............................................................................................................

Hardware Contents ...................................................................................... ...................

Replacement Part List ...................................................................................................... 17

PACKAGE CONTENTS

1A Ceiling Plate

1B Motor Assembly

1C Switch Housing

3D Blade

1E Light Kit

1F Bowl

1G Remote Unit

PART DESCRIPTION QUANTITY

1H Trim Ring [Preassembled

on Motor Assembly (B)]

Mounting Screw

[Preassembled on Motor

Assembly (B )]

Mounting Plate Screw

[Preassembled on Motor

Assembly (B )]

Switch Housing Screw

[Preassembled on Switch

Housing (C )]

PART DESCRIPTION QUANTITY

X2X6

CR2032 3V

Blade Screw

Qty 12+1 extra

HARDWARE CONTENTS

SAFETY INFORMATION

(not shown actual size)

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product.

. All electrical connections must comply with local codes, ordinances or the National Electric Code (NEC).

Contact your municipal building department to inquire about your local codes, permits and/or inspections.

. Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse

or by switching off circuit breaker.

. Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.

Never use a fixture in a two-wire system that is not grounded.

. If you are not sure your lighting system has a grounding means, do not attempt to install this fixture. Contact

a qualified, licensed electrician for information regarding proper grounding methods as required by the local

electrical code in your area.

. Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the floor

and at least 30 in. from the ends of the blades to any obstruction.

. If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type

and electrical rating required.

. The lighting fixture must be positioned so there is at least 1.64 ft. between the bulb and any illuminated

surface.

. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be

connected to a grounded conductor power supply. If the conductor of a fan is identified as an ungrounded

conductor, then it should be connected to an ungrounded conductor power supply. If the conductor of a fan

is identified for equipment grounding, then it should be connected to an equipment-grounding conductor.

. Installing a fixture into an electrical system without a proper grounding means could allow metal parts of the

fixture to carry electrical currents. If any of the fixture wires, wire connections or splices are broken, cut or

loose during the mounting or normal operation of the fixture, under such conditon, anyone coming in contact

with the fixture is subject to electrical shock, which could cause serious injury or death.

. Connection of the bare or green fixture ground wire to the black or white house wires may allow metal parts

of the fixture to carry electrical currents. Under this condition anyone coming in contact with the fixture will

receive electrical shock, which could cause serious injury or death.

. Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires

to have contact with any surface having a sharp edge. Doing so may damage or cut the wire insulation,

which could cause serious injury or death from electric shock.

DANGER

WARNING

CAUTION

PREPARATION

Estimated Assembly Time:

and Wrench.

Chemical Burn Hazard. Keep batteries away from children. This remote contains a lithium button cell battery.

If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal

burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the

battery compartment does not close securely, stop using the product, remove the batteries, and keep it away

from children. If you think batteries might have been swallowed or placed inside any part of the body, seek

immediate medical attention.

Dispose of cells properly and keep away from children. Even used cells may cause injury.

INITIAL INSTALLATION INSTRUCTIONS

This fan was designed to be mounted only on flat

ceilings and can be used on ceilings less than 9 feet

high (blades should be a minimum of 7 feet from the

floor. It is requred at least 30 inch from blade tip to

nearest wall or obstruction).

Fan mounting option:

2..

7 ft. MIN.

30 IN.

MIN.

DANGER:

Failure to disconnect power supply prior to

Turn off circuit breakers and wall switch to the fan supply

line leads.

installation may result in serious injury or death.

Turn Off Power Source

Check existing outlet box (not included) to ensure it is

securely fastened to at least two points in a structural

ceiling member and can support the full weight of the

fan.Once verified, install ceiling plate (A) to the outlet

box using the screws and washers provided with the

outlet box.

DANGER:

A loose outlet box can cause the fan to

wobble and increase the fan’s potential to fall, which

could result in serious injury or death.

4.Partially remove two diagonal mounting screws (I) on

the round holes, keep for later use. And loosen the

other two screws (I).

5.Hang the motor assembly (B) onto the hook from the

ceiling plate (A). This will allow for hands-free wiring.

INITIAL INSTALLATION INSTRUCTIONS

WIRING INSTRUCTIONS

Hardware Used

Wire Connector x 6

2. Wrap electrical tape (not included) around each wire

connector and make sure no bare wire or wire strands

are visible after making connections. Then, turn wires

upward and carefully push them into the outlet box;

make sure the WHITE and GREEN connections are on

one side and the BLACK connections are on the other

side.

WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse

box before hanging.

WARNING: If you are not sure if the outlet box is grounded, contact a licensed electrician for

advice, as it must be grounded for safe operation.

WARNING: If house wires are different colors than referred to in the following steps, stop

immediately. A professional electrician is recommended to determine proper wiring.

WARNING: If you feel that you do not have enough electrical wiring knowledge or experience,

have your fan installed by a licensed electrician.

1. Follow steps below to wiring your fan, once wiring step

has been completed, slide the wired receiver into the

motor assembly (B) with the flat side of the receiver

facing the ceiling.

TO MOTOR N from the receiver.

FOR LIGHT from the receiver.

TO MOTOR L from the receiver.

marked AC IN L from the receiver.

marked AC IN N from the receiver.

Connect GROUND (GREEN) wires from ceiling plate

and fan assembly, to GROUND (GREEN or BARE

COPPER) from house.

1. After wire connections, take the motor assembly (B)

off the hook.Raise the motor assembly (B) up to the

ceiling plate (A).Align two remained screws (I) on the

motor assembly (B) to the keyholes on the ceiling

plate (A), rotate clockwise until the screw heads

engage the keyhole slots fully. Make sure not to

break any wire connections.

2. Re-install two mounting screws (I) to the round holes,

securely tighten four (4) mounting screws (I).

FINAL INSTALLATION INSTRUCTIONS

3. Lift the trim ring (H) up, aligning four notches on the

canopy of motor assembly (B) with raised areas on the

inner side of trim ring (H) and pop it into the canopy.

Canopy

4. Insert blade (D) through slot on fan motor assembly

(B), align with four screws holes, securely tighten

with blade screws (AA). Repeat for remaining blades.

Hardware Used

x 12

Blade Screw

5. Remove one of the mounting screws (J) on the

mounting plate of motor assembly (B) and keep for

later use. And loosen the other two.

FINAL INSTALLATION INSTRUCTIONS

Insert the 9 pin connector from the motor assembly (B)

through the center hole in the switch housing (C).

Attach the switch housing (C) to the mounting plate on

the motor assembly (B) by placing the keyhole slots

from the switch housing (C) onto the two protruding

mounting screws (J ) heads. Adjust the switch housing

then re-insert mounting screw (J) previously removed

on step 5. Tighten all mounting screws (J) securely.

Mounting Plate

Mounting

Plate

This manual suits for next models

Table of contents

Other Harbor Breeze Fan manuals

Harbor Breeze

Harbor Breeze KINGSBURY 40190 User manual

Harbor Breeze

Harbor Breeze HTD21011 User manual

Harbor Breeze

Harbor Breeze LP8072LAZ User manual

Harbor Breeze

Harbor Breeze 40821 User manual

Harbor Breeze

Harbor Breeze MERRIMACK 40942 Manual

Harbor Breeze

Harbor Breeze BTH44ABZC5C User manual

Harbor Breeze

Harbor Breeze 40680 User manual

Harbor Breeze

Harbor Breeze CUMBERLAND 42476 User manual

Harbor Breeze

Harbor Breeze SOUTH RIVER C-ST52BNK5D1 User manual

Harbor Breeze

Harbor Breeze MAZON MZ44MBK3LR User manual

Harbor Breeze

Harbor Breeze ANNANDALE 42864 User manual

Harbor Breeze

Harbor Breeze 40094 User manual

Harbor Breeze

Harbor Breeze 873 User manual

Harbor Breeze

Harbor Breeze Cape Coast E-YLM52WW5C1 User manual

Harbor Breeze

Harbor Breeze 42079 User manual

Harbor Breeze

Harbor Breeze MAZON MZ44BNK3LR User manual

Harbor Breeze

Harbor Breeze 00728 User manual

Harbor Breeze

Harbor Breeze CAF48BNK5L User manual

Harbor Breeze

Harbor Breeze 40093 User manual

Harbor Breeze

Harbor Breeze 40959 User manual

Harbor Breeze

Harbor Breeze ARMITAGE CC52WW5C User manual

Harbor Breeze

Harbor Breeze C-UT56TBC3M User manual

Harbor Breeze

Harbor Breeze LAKE LAGODA LP8300LAZ User manual

Harbor Breeze

Harbor Breeze TIEMPO E-TM52BNK5CS User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual