Harbor Breeze 42079 User manual
1
ATTACH YOUR RECEIPT HERE
Purchase Date ___________________________
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
RR20275
ITEM #0883775, 2758998
ALTISSA CEILING FAN
MODEL #42079, 42242
Español p. 22
H
H
a
r
b
o
r
B
r
e
e
z
e
a
r
b
o
r
B
r
e
e
z
e
LISTED FOR
DAMP LOCATION
2
TABLE OF CONTENTS
Package Contents .................................................................3
Hardware Contents ................................................................4
Safety Information .................................................................5
Preparation ......................................................................6
Initial Installation ..................................................................7
Standard or Angle Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Wiring .........................................................................11
Final Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operating Instructions .............................................................17
Care and Maintenance ............................................................18
Troubleshooting..................................................................18
Limited Lifetime Warranty ..........................................................20
Replacement Parts List ............................................................21
3
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Downrod 1
B Downrod Pin (preassembled to Downrod [A]) 1
C Downrod Clip (preassembled to Downrod [A]) 1
D Mounting Bracket (preassembled to Canopy [E]) 1
E Canopy 1
F Canopy Cover (preassembled to Canopy [E]) 1
G Yoke Cover 1
H Light Pan 1
I Glass Bowl 1
JMotor Assembly 1
K Set Screw (preassembled to Motor Assembly [J]) 2
L Fitter Plate (preassembled to Motor Assembly [J]) 1
M Fitter Plate Screw (preassembled to Fitter Plate [L]) 3
N Light Kit 1
O Light Frame 1
P Bulb 2
Q Finial Cap 1
RBlade Arm 5
S Blade 5
T Hex Nut (preassembled to light kit [N]) 1
U Finial (preassembled to Light Kit [N]) 1
V Mounting Bracket Screw (preassembled to Mounting Bracket [D]) 4
W Light Pan Screw (preassembled to Light Pan [H]) 3
X Light Kit Screw (preassembled to Light Pan [H]) 3
A
B
C
D
E
FG
H
W X
N
L
K
J
I
OP
Q
S
U
V
R
MT
4
HARDWARE CONTENTS (shown actual size)
Wire Connector
Qty. 3
+ 1 extra
Blade Screw
Qty. 15
+ 1 extra
Blade Washer
Qty. 15
+ 1 extra
Pull Chain Extension
Qty. 2
Motor Screw
Qty. 15 + 1 extra
AA BB CC DD XX
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e
5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning o the circuit
breakers.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the oor and at least 30 in. from the end of the blades to any obstruction.
• The net weight of this fan is: 22.42 lbs.
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan
parts with sharp edges.
WARNING: Using a full-range dimmer switch to control fan speed will cause a loud humming
noise from the fan. To reduce the risk of re or electric shock, do NOT use a full-range dimmer switch
to control the fan speed.
WARNING: To reduce the risk of re, electric shock or personal injury, mount the fan to an
outlet box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with
the outlet box. Most outlet boxes commonly used for the support of lighting xtures are not acceptable
for fan support and may need to be replaced. Consult a qualied electrician if in doubt. Secure the
outlet box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.).
WARNING: To reduce the risk of re, electric shock or personal injury, wire connectors provided
with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If
your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the
two fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING: To reduce the risk of re, electric shock or personal injury, do not bend the blade
arms when installing them, balancing the blades or cleaning the fan. Do not insert objects between
the rotating fan blades.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use
of parts OTHER than those provided with this fan will void the warranty.
6
SAFETY INFORMATION
CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.
CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are
secured.
CAUTION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
HKC-US
3350 Players Club Parkway, Suite 225
Memphis, TN 38125
(800) 643-0067
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with
the package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Step Ladder, Wire Cutters and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure and Wiring Handbook
7
INITIAL INSTALLATION
1. Turn o the circuit breakers and the wall switch to the
fan supply line leads.
DANGER: Failure to disconnect the power
supply prior to installation may result in serious injury
or death.
2. Determine the mounting method to use.
Standard Mounting is best suited for ceilings 8 ft.
or higher. For taller ceilings you may want to use a
longer downrod (not included).
Angle Mounting is best suited for angled or vaulted
ceilings. A longer downrod is sometimes necessary
to ensure proper blade clearance. Note: If using the
angle mount, check to ensure the ceiling angle is not
steeper than 16°.
Flushmount Installation is not available for this item.
Closemount Installation is not available for this item.
2
Standard Mounting
Flushmount Closemount
Angle Mounting
3. Ensure the blades (S) will be at least 30 in. from
any obstructions. Also check the downrod (A) length
to ensure the blades (S) will be at least 7 ft. above
the oor.
7 ft. min.
30 in. min.
3
A
S
1
8
INITIAL INSTALLATION
4. Loosen all four preassembled mounting bracket
screws (V), then completely remove the two mounting
bracket screws (V) from the round holes of canopy
(E). Set aside for later use.
Detach mounting bracket (D) from canopy (E).
5. Secure the mounting bracket (D) to the outlet box
(not included) using screws and washers provided
with the outlet box.
CAUTION: It is very important you use the proper
hardware when installing the mounting bracket (D) as
this will support the fan.
E
V
D
4
5
D
D
Standard
Mount
Angle
Mount
D
D
9
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
1. Remove the downrod clip (C) and downrod pin (B)
from the downrod (A). Then partially loosen the
set screws (K) in the yoke at the top of the motor
assembly (J).
2. Insert the downrod (A) through the canopy (E) and
yoke cover (G). Feed the wires from the motor
assembly (J) through the downrod (A).
3. Slide the downrod (A) into the yoke of the motor
assembly (J), align the holes, then re-install the
downrod pin (B) and downrod clip (C). Secure with
set screws (K).
C
B
A
A
G
J
E
2
3
Yoke
B
A
J
C
K
K
J
1
10
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
4. Depending on the length of downrod you use, you may
need to cut the lead wires back to simplify the wiring. If
you decide to cut back the lead wires, it is suggested
you do so in the following manner: Take the lead wires
and make sure you have pulled them all the way
through the top of the downrod. Measure 8 inches of
lead wire, then cut the excess wire o with wire cutters
(not included).
5. If you decided to cut back the lead wire in Step 4, strip
1/2 in. of insulation from the end of the white wire.
Twist the stripped ends of each strand of wire within the
insulation with pliers (not included). Repeat this step for
black, blue and green wires.
Note: If you did not cut back the lead wires in Step 4, Step
5 is not necessary and you may proceed to Step 6.
6. Install the ball end of the downrod (A) into the opening of
mounting bracket (D). Align one of the four slots in the
ball with the tab in the mounting bracket (D). Note: The
downrod (A) should not rotate if installed correctly.
DANGER: Failure to align the slot in the downrod
(A) with the tab of the mounting bracket (D) may cause
the fan to wobble or fall, which could result in serious
injury or death.
5
4
A
D
Tab
Slot
8 in.
6
This manual suits for next models
3
Table of contents
Other Harbor Breeze Fan manuals
Harbor Breeze
Harbor Breeze BIRCHMOUNT COVE 41554 User manual
Harbor Breeze
Harbor Breeze 872 User manual
Harbor Breeze
Harbor Breeze 35061 User manual
Harbor Breeze
Harbor Breeze 0228113 User manual
Harbor Breeze
Harbor Breeze MAZON MZ44BNK3LR User manual
Harbor Breeze
Harbor Breeze TEX52MBK5C1L User manual
Harbor Breeze
Harbor Breeze MERRIMACK 40942 Manual
Harbor Breeze
Harbor Breeze 42612 User manual
Harbor Breeze
Harbor Breeze 40959 User manual
Harbor Breeze
Harbor Breeze EDENTON L2B1 User manual
Harbor Breeze
Harbor Breeze Calera User manual
Harbor Breeze
Harbor Breeze 00881 User manual
Harbor Breeze
Harbor Breeze CLASSIC STYLE BDB52LW5N User manual
Harbor Breeze
Harbor Breeze LAKE PLACIDO CPK1261 User manual
Harbor Breeze
Harbor Breeze 0883783 User manual
Harbor Breeze
Harbor Breeze 40945 User manual
Harbor Breeze
Harbor Breeze BOD52MW3 User manual
Harbor Breeze
Harbor Breeze OCEANSIDE User manual
Harbor Breeze
Harbor Breeze E-BDB52ABZC5BC4N User manual
Harbor Breeze
Harbor Breeze 35086 User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
