Harbor Breeze 42224 User manual

9689 • 090120 1

ELMHURST CEILING FAN

Owner’s Manual

Model #42224

Item #2599769

To obtain service, please contact the Service Department:

1-877-706-3267, 8 a.m. - 5 p.m. Central, Monday - Friday.

PACKAGE CONTENTS

1. Mounting Bracket

2. Canopy

3. Mounting Bracket Screw

(x4)

4. Canopy Cover

5. Downrod

6. Downrod Pin

7. Downrod Clip

8. Yoke Cover

9. Set Screw (x2)

10. Motor Assembly

11. Motor Screw (x6)

12. Fitter Plate

13. Fitter Plate Screw (x4)

14. Light Pan

15. Light Pan Screw (x3)

16. Cage Screw (x4)

17. Light Kit

18. Glass Bowl

19. Light Cage

20. Blade (x3)

21. Blade Arm (x3)

22. Remote Pack

23. Hardware Kit

24. Owner’s Manual

25. Blade Screw (x9)

26. Blade Washer (x9)

27. Wire Connector (x4)

Unpack your fan and check the contents. You should

have the following items:

PACKAGE CONTENTS

HARDWARE CONTENTS

Note: Some extra hardware has been included. The quantity

listed above is the number required for installation.

HARDWARE CONTENTS

TOOLS REQUIRED (not included)

Tools required for assembly: Electrical tape, Phillips Screwdriver, Pliers, Safety Glasses, Step Ladder, Wire Cutters

and Wire Strippers

Helpful Tools: AC Tester Light, Tape Measure, and Wiring Handbook

272625

Hardware Kit

Owner’s

Manual

A. 16.46 in. B. 10.82 in. C. 9.53 in. D. 5.13 in.

DIMENSION REFERENCE

MOUNTING OPTIONS

Choose one of the following mounting options:

Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer

downrod (not included).

Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary

to ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is

not steeper than 10°.

Two Mounting Options

Downrod Mount Angled Ceiling Mount (Up to 10 degrees)

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE

FAN AND SAVE INSTRUCTIONS.

All set screws of the fan must be checked and retightened where necessary before installation.

To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing

the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.

Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.

The safeguards provided by these safety instructions and by the separate installation instructions are not

meant to cover all possible conditions and situations that may occur. It must be understood that common

sense, caution and care are factors which can not be built into this product. These factors must be supplied

by the person(s) installing, caring for and operating the fan.

The fan weight is Net Weight: 16.78 lb (7,61 kg). Be sure the outlet box (not included) is securely attached

to the building structure and is marked “Acceptable For Fan Support”. Failure to do so can result in serious

injury.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver

--Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Please note changes or modications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

HKC-US

3350 Player’s Club Parkway, #225

Memphis, TN 38125

1-877-706-3267

SAFETY INSTRUCTIONS

CAUTION:

WARNING:

To avoid risk of electric shock, be sure to shut o power at the main fuse or circuit breaker box before

installing or servicing this xture. Turning o the electrical power by using the light switch is not

sucient to prevent electrical shock.

To reduce the risk of injury, install the fan so that the blades are at least 7 feet (2.1 Meters) above the

oor and at least 18 inches (0.5 Meters) from the tip of the blades to the wall.

To reduce the risk of re, electric shock, or personal injury, mount to outlet box marked “acceptable for

fan support” and use mounting screws provided with the outlet box.

The installation has to be in accordance with the national electrical code, ANSI/NFPA 70-1999 and

local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a

qualied licensed electrician.

Using a full-range dimmer switch to control fan speed will cause a loud humming noise from the fan. To

reduce the risk of re or electric shock, do NOT use a full-range dimmer switch to control the fan speed.

SAFETY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

2. Remove the mounting bracket by removing the two

mounting bracket screws from the round holes in the

canopy. Then loosen the other two mounting bracket

screws from the J-shaped slots. Retain the mounting

bracket screws for later.

3. Install the mounting bracket to the outlet box (not

included) using the screws and washers provided with

the outlet box.

WARNING: To reduce the risk of re, electric shock,

or personal injury, mount to the outlet box marked

“acceptable for fan support” and use the mounting

screws and washers provided with the outlet box.

Angled Ceiling Mount

Downrod Mount

Mounting Bracket Screw

1. Turn OFF the electrical power at the main fuse or circuit

breaker.

DANGER: Failure to disconnect the power supply prior to

installation may result in serious injury or death.

4. Remove the six motor screws from the underside of

the motor assembly and save for blade arm installation.

Motor Screw Motor Assembly

Tab

Slot

Downrod

Receiver

8. Install the ball end of the downrod into the opening of

mounting bracket. Rotate the downrod until the tab in the

mounting bracket is seated in the slot in the downrod ball.

WARNING: The fan and/or downrod should not rotate in

the mounting bracket, if installed correctly. Failure to align

the slot in the downrod ball with the tab on the mounting

bracket may result in fan falling causing serious injury or

death.

Insert the receiver from remote pack into the mounting

bracket with antenna end rst and the at side facing the

ceiling. Note: The receiver will rest on the downrod.

Note: There is an adhesive sticker on one of the antennas

connected to the receiver. For best results, stick the

antenna to the ceiling.

Downrod Pin

Downrod Clip

Yoke

Downrod

Set Screw

7. Slide the downrod into the yoke of the motor assembly,

align the holes, then re-install the downrod pin and

downrod clip. Secure with the two set screws and slide

the yoke cover down until it rests on top of the motor

assembly.

Note: With wiring extending out of the downrod,

measure 8 inches of lead wire and cut the excess wire with

wire cutters (not included). Then strip 1/2” of insulation

from the end of each wire.

ASSEMBLY INSTRUCTIONS

Mounting

Bracket

6. Insert the downrod through the canopy and yoke

cover. Feed the wires from the fan through the downrod.

Canopy

Yoke Cover

Downrod

Yoke

Downrod

Clip

Downrod

Set Screw

Yoke

5. Remove the downrod clip and downrod pin from the

downrod. Then loosen but do not remove the two set

screws in the yoke at the top of the motor assembly.

ASSEMBLY INSTRUCTIONS

Black (hot/power)

Push-in Connector

Wire Connector

White (neutral)

Bare/Green

(ground)

White

Black

Blue

Black

Green

Receiver

Black

White

Canopy J-slot

Round

Hole

Mounting Bracket Screw

Blade Screw

Blade Washer

Blade

Blade Arm

10. Raise the canopy, ensure the two mounting bracket

screws are aligned with the J-shaped slots in the canopy.

Then turn the canopy in a clockwise direction until the

mounting bracket screws are completely engaged in

the J-shaped slots. Install the two previously removed

mounting bracket screws in the round holes. Securely

tighten all mounting bracket screws.

11. Partially insert the blade screws along with the blade

washers through the blade and into the blade arm.

Tighten each blade screw with a Phillips screwdriver (not

included), starting with the one in the middle.

Repeat this step for the remaining blades and blade arms.

9. Use wire connectors and push-in connectors to connect

the receiver and fan wires to the supply wires from outlet

box according to the wiring diagram and the following

instructions:

• Connect the Green wires from the fan and the mounting

bracket to the Bare/Green (ground) supply wire.

• Connect the Blue wire (FOR LIGHT) from the receiver to

the Blue fan wire.

• Connect the Black wire (TO MOTOR L) from the receiver to

the Black fan wire.

• Connect the White wire (TO MOTOR N) from the receiver

to the White fan wire.

• Push the Black (Hot/Power) supply wire into the empty

wire hole in push-in wire connector preassembled to the

Black wire (AC IN L).

• Push the White (neutral) supply wire into the empty wire

hole in push-in wire connector preassembled to the White

wire (AC IN N).

Important: After the connections have been made, the

connected wires should be turned upward and pushed

carefully up into the outlet box. Place the black and white

wire connections on opposite sides of the outlet box.

ASSEMBLY INSTRUCTIONS

14. Remove one of the three light pan screws from the

light pan and loosen the other two but do not remove.

Connect the 9-pin connectors from the light pan to the

9-pin connectors from the light kit. Lift the two keyhole

slots in the light kit over the two loosened light pan

screws and turn in a clockwise direction. Then, use the

previously removed light pan screw to secure the light kit

to the light pan. Tighten all screws.

Light Kit

Light Pan Screw

Light Pan

9-pin

Connector

Glass Bowl

Light Kit

15. Attach the glass bowl to the light kit by twisting the

glass bowl tightly in a clockwise direction until it is secure.

CAUTION: Avoid cross-threading the glass during

installation. Improper installation could cause the glass

bowl to be dicult to remove or fall, which could cause

serious injury.

13. Remove one of the four tter plate screws

preassembled to the tter plate and loosen the other three

but do not remove. Feed the 9-pin connector through

center hole in light pan. Align the keyhole slots in the light

pan with the loosened screws in the tter plate. Turn light

pan clockwise and replace the previously removed tter

plate screw. Tighten all screws.

Fitter Plate Screw

Keyhole

Slot

Keyhole

Slot

Fitter

Plate

Light Pan

Motor Screw

Blade Arm

12. Install the blade arm to the underside of the motor

assembly with previously removed motor screws. Tighten

each blade arm completely before moving to the next.

ASSEMBLY INSTRUCTIONS

Mounting

Screw

Battery Door

Battery Compartment

Front

Keyhole

Slot

Light

Cage

Cage Screw

Back

Wall Bracket

17. Remove the battery door from the back of the remote

using a at-head screwdriver (not included). Insert the two

CR2032 batteries into the remote; ensure the positive pole

of the batteries face up (as pictured) and then replace the

battery door.

Note: Your fan and wall control/remote were synced at the

factory. If the wall control does not operate the fan, see

TROUBLESHOOTING, page 13.

16. Loosen all four and completely remove one of the cage

screws preassembled to the light pan. Then lift the keyhole

slots in the light cage over the loose cage screws and turn

in a clockwise direction. Reinstall the previously removed

cage screw and tighten all screws.

18. If desired, the wall bracket can be installed to the wall

using the two mounting screws. Store the remote in the

wall bracket when not in use.

Turn ON the electrical power at the main fuse or circuit

breaker and the wall switch.

Installation is complete.

This manual suits for next models

Table of contents

Other Harbor Breeze Fan manuals

Harbor Breeze

Harbor Breeze RLG52NWZ5L User manual

Harbor Breeze

Harbor Breeze 41239 User manual

Harbor Breeze

Harbor Breeze LP8210LAZ User manual

Harbor Breeze

Harbor Breeze 40107 User manual

Harbor Breeze

Harbor Breeze Teolo User manual

Harbor Breeze

Harbor Breeze BOLTZ 42300 User manual

Harbor Breeze

Harbor Breeze TILGHMAN WCK52LMW5N User manual

Harbor Breeze

Harbor Breeze E-BDB52ABZC5BC4N User manual

Harbor Breeze

Harbor Breeze 40101 User manual

Harbor Breeze

Harbor Breeze KIAWAH User manual

Harbor Breeze

Harbor Breeze SOUTHLAKE LP8055LAZ User manual

Harbor Breeze

Harbor Breeze 0883783 User manual

Harbor Breeze

Harbor Breeze SAWGRASS User manual

Harbor Breeze

Harbor Breeze FAIRWIND User manual

Harbor Breeze

Harbor Breeze CEDAR HILL User manual

Harbor Breeze

Harbor Breeze MAZON MZ44BNK3LR User manual

Harbor Breeze

Harbor Breeze BTH44ABZC5C User manual

Harbor Breeze

Harbor Breeze HTE21091 User manual

Harbor Breeze

Harbor Breeze WO52BB5C User manual

Harbor Breeze

Harbor Breeze VALDOSTA L1120H-BK User manual

Harbor Breeze

Harbor Breeze 42612 User manual

Harbor Breeze

Harbor Breeze ANNANDALE 42864 User manual

Harbor Breeze

Harbor Breeze 40093 User manual

Harbor Breeze

Harbor Breeze 40410 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual