Harbor Breeze CEDAR HILL User manual

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-527-1292, 8:30 a.m.-5 p.m., CST, Monday-Friday.

ITEM #0312114

MODEL #E-PEN44BCW5MC

CEDAR HILL CEILING FAN

español p. 20

Harbor Breeze® is a registered trademark

E206035

Federal regulations require all ceiling fans with light kits manufactured

or imported after January 1, 2009, to limit total wattage consumed by the

light kit to 190W. Therefore, this fan is equipped with a wattage limiting

device.

TABLE OF CONTENTS

Safety Information ....…………………………………………………………………………...……..….3

Package Contents ........…………………………………………………………………..……..…..…..4

Hardware Contants ........................................................................................................................5

Preparation .........….…………………..……………………….…………….………………....6

Initial Installation ...............……………………...………………………………….............6 - 7

Downrod Style Fan Mounting ...…………………………....……………....……..........................8 - 9

Closemount Style Fan Mounting ……………………...............…....……………………....9 - 10

Wiring ..............................................................................………………………..............10 - 12

Final Installation ………….…………….……………………….………….....…....................12 - 15

Fan Operation ..............................................................………………………………...15 - 16

Care and Maintenance ....……………………………………………………………….......................16

Troubleshooting .....................………...………………………….……………..………...........17 - 18

Warranty ………………………………….…………………………………………..……..............18

Replacement Parts List ...............................................................................................................19

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate

the product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.

1. Before you begin installing the fan, disconnect the power by removing fuses or turning off

circuit breakers

CAUTION: Read all instructions and safety information before installing your new fan.

Review the accompanying assembly diagrams.

CAUTION: To avoid personal injury, the use of gloves may be necessary while

handling fan parts with sharp edges.

4. Make sure that all electrical connections comply with local codes, ordinances, the National

Electrical Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a

do-it-yourself wiring handbook, available at Lowe's, if you are unfamiliar with installing

electrical wiring.

5. Make sure the installation site you choose allows a minimum clearance of 7 feet from the

blades to the floor and at least 30 in. from the end of the blades to any obstruction.

6. WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount fan to

outlet box marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided

with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are

not acceptable for fan support and may need to be replaced. Consult a qualified electrician if

in doubt. Secure the box directly to the building structure. The outlet box and its support must

be able to support the moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet

box.

7. After you install the fan, make sure that all connections are secure to prevent the fan from

falling.

8. WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire

connectors provided with this fan are designed to accept only one 12 gauge house wire and

two lead wires from the fan. If your house wire is larger than 12 gauge or there is more than

one house wire to connect to the two fan lead wires, consult an electrician for the proper size

wire connectors to use.

9. WARNING: To reduce the risk of fire or electric shock, do not use the fan with

any solid state speed control device or control fan speed with a full range dimmer

switch.

10. WARNING: To reduce the risk of fire, electric shock, or personal injury, do not bend

the blade arms when installing them, balancing the blades, or cleaning the fan. Do not insert

objects between the rotating fan blades.

11. WARNING: To reduce the risk of personal injury, use only parts provided with this

fan. The use of parts OTHER than those provided with this fan will void the warranty.

12. The net weight of this fan including the light kit is: 16.31 lbs. (7.4 kg).

D E

L M

N O

PACKAGE CONTENTS

Part Description Quantity

A Downrod 1

B Canopy 1

C Mounting Bracket(pre-attached to canopy) 1

D Yoke Cover 1

E Motor Housing 1

F Switch Housing Cap(pre-attached to motor housing) 1

G Glass Shade 1

H Blade Arm 5

I Blade 5

J Pull Chain Extension (in hardware pack)

K Light Kit Fitter 1

L Finial Plate (pre-attached to light kit fitter) 1

M Finial (pre-attached to light kit fitter)

N Candelabra Base Bulb 3

O Canopy Cover (pre-attached to canopy) 1

IMPORTANT REMINDER: You must use

the parts provided with this fan for proper

installation and safety.

HARDWARE CONTENTS

Part Description Quantity Part Shown to Size

Motor Screw (10 in motor; 1 in hardware pack) 11

3/16 Blade Screw (in hardware pack) 16

5.4M/M Lock Washer (10 in motor; 11

1 attached to motor screw in hardware pack)

Blade Washer (in hardware pack) 16

E3 Wire Connector (in hardware pack) 4

Canopy Mounting Screw 4

(attached to mounting bracket)

Pin (in downrod) 1

Clip (attached to pin) 1

Hex Nut (pre-attached to light kit fitter) 1

Lock Washer (pre-attached to light kit fitter) 1

3/16 x 11 mm Screw (in hardware pack) 3

5 mm Lock Washer (in hardware pack) 3

1. Turn off circuit breakers and wall switch to the fan supply

line leads. (Fig. 1)

DANGER: Failure to disconnect power supply prior

to installation may result in serious injury or death.

Fig. 1

Fig. 2

2. Determine mounting method to use. (Fig. 2)

A. Downrod mount (normal or angled ceiling)

B. Closemount (normal ceiling only)

Important: If using the angle mount, check to make sure

the ceiling angle is not steeper than 19°.

INITIAL INSTALLATION

PREPARATION

1. Before beginning assembly, installation or operation of product, make sure all parts are

present. Compare parts with package contents list and diagram above. If any part is missing or

damaged, do not attempt to assemble, install or operate the product.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included):

electrical Phillips pliers safety stepladder wire

tape screwdriver glasses strippers

Helpful Tools (not included):

A/C tester tape do-it-yourself wiring handbook

light measure (available at Lowe’s) wire cutters

Bulbs Required (included):

3 candelabra base

60 watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely

attached to the building structure and can support the full weight of the fan. Failure to do this can

result in serious injury or death. The stability of the outlet box is essential in minimizing wobble

and noise in the fan after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire

is present.

2. After opening top of carton, remove mounting hardware package from foam inserts. Remove

motor from packing and place on carpet or on foam to avoid damage to finish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that

they are secured.

A-15

Canopy Mounting Screw x 4

INITIAL INSTALLATION

4. Loosen canopy mounting screws (FF) in

slotted holes in canopy (B) and remove the

other two screws (FF)--save screws (FF) for

later use. Remove mounting bracket (C) from

canopy (B). (Fig. 4A) Secure mounting bracket

and flat washers provided with the outlet box.

(Fig. 4B)

*Note: It is very important that you use the

proper hardware when installing the mounting

bracket (C) as this will support the fan.

Important: If using the angle mount, make

sure open end of mounting bracket (C) is

installed facing the higher point of the ceiling.

5. Remove motor screws (AA) and lock washers

(CC) from underside of motor and save for blade

arm (H) attachment later on. [If there are plastic

motor blocks installed with the motor screws (AA)

and lock washers (CC), discard the plastic motor

blocks.] (Fig. 5)

Follow mounting instructions on page 8 and or 9

depending on mounting method (A or B) chosen in

Step 2 on previous page.

Fig. 5

Fig. 4A

Fig. 4B

FF FF

Hardware Used

Motor Screw x 10

Hardware Used

5.4 M/M Lock Washer x 10

3. Check to make sure blades (I) are at least 30 in. from

any obstruction and at least 7 ft. above the floor. (Fig. 3) Fig. 3

7 ft.

min.

30 in.

min.

DOWNROD STYLE FAN MOUNTING

3. Slip downrod (A) into motor housing yoke, align holes

and re-install pin (GG) and clip (HH). Re-tighten set

screws in motor housing yoke and then tighten nuts.

Slide yoke cover (D) down until it rests on top of motor

housing (E). (Fig. 3)

2. Insert downrod (A) through canopy (B) and

yoke cover (D). Thread wires from motor

housing (E) through downrod (A). (Fig. 2)

Fig. 2

Fig. 3

Set Screw

Hardware Used

Pin x 1

Clip x 1

1. Remove pin (GG) and clip (HH) from

downrod (A). (Fig. 1A) Partially loosen set

screws in motor housing yoke at top of motor

housing (E). (Fig. 1B)

*Helpful Hint: Downrod style mounting is

best suited for ceilings 8 ft. (2.44 m) high or

higher. For taller ceilings you may want to use

a longer downrod (not included) than the one

provided. Angle style mounting is best suited

for angled or vaulted ceilings. A longer

downrod is sometimes necessary to ensure

proper blade clearance.

Set

Screw

Fig. 1A Fig. 1B

Hardware Used

Pin x 1

Clip x 1

4. Depending on the length of downrod (A) you use, you

may need to cut the lead wires back to simplify the wiring.

If you decide to cut back the lead wires, it is suggested

that you do so in the following manner:

Take the lead wires and make sure that you have pulled

them all the way through the top of the downrod (A). Start

at the TOP of the ball on the downrod (A) and measure 8

in. of lead wire, and then cut the excess wire off with wire

cutters. (Fig. 4)

Note: If you did not cut back the lead wires, Steps 4 and

5 are not necessary and you may proceed to Step 6

instead.

6. Install ball end of downrod (A) into mounting

bracket (C) opening. Align slot in ball with tab in

mounting bracket (C). (Fig. 6)

DANGER: Failure to align slot in ball with

tab may result in serious injury or death.

Continue to "Wiring" instructions on page 10.

Fig. 6

Hanging

Ball Slot

1. Remove canopy cover (O) from bottom of canopy (B).

(Fig. 1) [Note: It may be necessary to use the handle end of

a screwdriver to remove the canopy cover (O) by tapping

on the canopy cover (O) from the inside of the canopy (B).]

*Helpful Hint: Close style mounting is more suitable for

ceilings lower than 8 ft. (2.44 m) high. The downrod (A),

hanging ball, yoke cover (D), and canopy cover (O) are not

used in this type of installation.

Fig. 1

CLOSEMOUNT STYLE FAN MOUNTING

Tab

Ball

DOWNROD STYLE FAN MOUNTING

5. If you decided to cut back the lead wires in Step 4, strip

1/2 of an inch of insulation from end of white wire. Twist

stripped ends of each strand of wire within the insulation

with pliers. (Fig. 5) Repeat Step 5 for black, blue (if

applicable) and green wires.

Fig. 5

Fig. 4

Ball

WIRING

WARNING: To reduce the risk of fire, electrical

shock, or personal injury, wire connectors provided

with this fan are designed to accept only one 12 gauge

house wire and two lead wires from the fan. If your

house wire is larger than 12 gauge or there is more

than one house wire to connect to the two fan lead

wires, consult an electrician for the proper size wire

connectors to use.

CAUTION: Be sure outlet box is properly

grounded and that a ground (green or bare) wire is

present.

WARNING: If house wires are different colors

than referred to in the following steps, stop immediately.

A professional electrician is recommended to determine

wiring.

2. Pull wires through hole in the middle of the canopy

(B) and attach canopy (B) to motor housing (E) using

the three screws (KK) and three lock washers (LL)

provided. (Fig. 2)

3. Hang motor housing (E) on the tab on the

mounting bracket (C) using one of the non-slotted

holes in the canopy (B). (Fig. 3)

Fig. 2

Fig. 3

Tab

Hardware Used

3/16 X 11 mm Screw x 3

5 mm Lock Washer x 3

CLOSEMOUNT STYLE FAN MOUNTING

Other manuals for CEDAR HILL

This manual suits for next models

Table of contents

Languages:

Other Harbor Breeze Fan manuals

Harbor Breeze

Harbor Breeze RLC52WW5C1R User manual

Harbor Breeze

Harbor Breeze CE-JP13EB6RC User manual

Harbor Breeze

Harbor Breeze 41239 User manual

Harbor Breeze

Harbor Breeze RC103L User manual

Harbor Breeze

Harbor Breeze MAYFIELD BTH44AB5CS User manual

Harbor Breeze

Harbor Breeze DUBOIS DM52BCP5CS User manual

Harbor Breeze

Harbor Breeze 35061 User manual

Harbor Breeze

Harbor Breeze Casual-3-2011 User manual

Harbor Breeze

Harbor Breeze Bath Ventilator with Light User manual

Harbor Breeze

Harbor Breeze TG52BNK3D1RC User manual

Harbor Breeze

Harbor Breeze Bath Ventilator with Light User manual

Harbor Breeze

Harbor Breeze AFTONSHIRE User manual

Harbor Breeze

Harbor Breeze URBANIA User manual

Harbor Breeze

Harbor Breeze 00887 User manual

Harbor Breeze

Harbor Breeze BOLTZ 42300 User manual

Harbor Breeze

Harbor Breeze 40662 User manual

Harbor Breeze

Harbor Breeze CHESHIRE II User manual

Harbor Breeze

Harbor Breeze 52 IN CLASSIC STYLE 40081 User manual

Harbor Breeze

Harbor Breeze BTH44ABZC5C User manual

Harbor Breeze

Harbor Breeze LYNSTEAD User manual

Harbor Breeze

Harbor Breeze L0982 User manual

Harbor Breeze

Harbor Breeze 40093 User manual

Harbor Breeze

Harbor Breeze AR09-52WHT User manual

Harbor Breeze

Harbor Breeze SHREVEPORT E-NO52AB5C4 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual