Harbor Breeze SAWGRASS User manual

ITEM #18032

SAWGRASS CEILING FAN

MODEL #E-LUB52BNK5C1S

Questions, problems, missing parts? Before returning to your retailer, call or contact our

customer service department at 1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

español p. 20

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device.

E192641

LISTED

For

Damp Location

Harbor Breeze® is a registered trademark

Safety Information ....................................................................................................................... 2 - 3

Package Contents ........................................................................................................................... 4

Hardware Contents ......................................................................................................................... 5

Preparation ...................................................................................................................................... 5

Initial Installation ........................................................................................................................ 6 - 7

Fan Mounting .............................................................................................................................. 7 - 9

Wiring ....................................................................................................................................... 9 - 11

Final Installation ...................................................................................................................... 12 - 15

Operation Instructions ............................................................................................................ 15 - 16

Care and Maintenance .................................................................................................................. 17

Troubleshooting ...................................................................................................................... 17- 18

Warranty ........................................................................................................................................ 18

Replacement Parts List ................................................................................................................. 19

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m.- 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook,

available at Lowe's, if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 19.4 lbs. (8.8 kg).

TABLE OF CONTENTS

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS" and use

mounting screws provided with the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet

box directly to the building structure. The outlet box and its support must be able to support the

moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your

house wire is larger than 12-gauge or there is more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

WARNINGS

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

SAFETY INFORMATION

DANGER

If using this fan in a DAMP location, this fan must be connected to a supply circuit that is protected

by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock

or death.

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

Clip (preassembled)

Canopy Mounting Screw

(preassembled)

Glass Shade

Fitter Plate

Threaded Washer

(preassembled)

R Finial Plate

(preassembled)

S Finial

(preassembled)

T Fitter Plate Screw

(preassembled)

Motor Plate Screw

(preassembled)

Pull Chain Extension

Candelabra-base Bulb

PART DESCRIPTION QUANTITY

Downrod 1

Canopy

Mounting Bracket

Yoke Cover

Motor Housing

Blade Arm

Blade

Light Kit Fitter

Canopy Cover

Motor Screw

(preassembled)

Lock Washer

(preassembled)

Pin (preassembled)

IMPORTANT REMINDER: You must use

the parts provided with this fan for proper

installation and safety.

HARDWARE CONTENTS (shown actual size)

Rubber

Blade

Washer

Qty. 15

BB CC

Blade

Screw

Qty. 15 E3 Wire

Connector

Qty. 4

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents above. If any part is missing or damaged, do not attempt to

assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself-Wiring Handbook

(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 3 candelabra-base 40-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor

from packing and place on carpet or on foam to avoid damage to ﬁnish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they

are secured.

PREPARATION

INITIAL INSTALLATION

Turn off circuit breakers and wall switch to the fan

supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

Determine mounting method to use. (Fig. 2)

A. Normal mount

B. Angle mount

Important: If using the angle mount, check to

make sure the ceiling angle is not steeper than 19°.

Check to make sure blades (G) are at least 30 in.

from any obstruction. Check downrod (A) length to

ensure blades (G) are at least 7 ft. above the floor.

(Fig. 3)

OFF

7 ft.

min.

30 in.

min.

Secure mounting bracket (C) to outlet box using

screws, spring washers, and flat washers provided

with the outlet box. (Fig. 4)

*NOTE: It is very important that you use the proper

hardware when installing the mounting bracket (C)

as this will support the fan.

IMPORTANT: If using the angle mount, make sure

open end of mounting bracket (C) is installed

facing the higher point of the ceiling.

5. Remove motor screws (J) and lock washers (K)

from underside of motor. (Fig. 5) Save motor

screws (J) and lock washers (K) for later use.

FAN MOUNTING

INITIAL INSTALLATION

Remove pin (L) and clip (M) from motor housing

yoke at top of motor housing (E) and partially

loosen set screws. (Fig. 1)

*Helpful Hint: Downrod style mounting is best

suited for ceilings 8 ft. (2.44 m) high or higher. For

taller ceilings you may want to use a longer

downrod (not included) than the one provided.

Angle style mounting is best suited for angled or

vaulted ceilings. A longer downrod is sometimes

necessary to ensure proper blade clearance.

Set

Screw

FAN MOUNTING

Depending on the length of downrod (A) you

use, you may need to cut the lead wires back to

simplify the wiring. If you decide to cut back the

lead wires, it is suggested that you do so in the

following manner:

Take the lead wires and make sure that you

have pulled them all the way through the top of

the downrod (A). Start at the TOP of the ball on

the downrod (A) and measure 8 in. of lead wire,

and then cut the excess wire off with wire cutters

(not included). (Fig. 4)

NOTE: If you do not cut back the lead wires,

Steps 4 and 5 are not necessary and you may

proceed to Step 6 instead.

2. Insert downrod (A) through canopy (B), canopy

cover (I) and yoke cover (D). [Note: Canopy

cover (I) must be turned with the shiny side

toward the motor housing (E).] Thread wires

from motor housing (E) through downrod (A).

(Fig. 2)

3. Slip downrod (A) into housing yoke, align holes

and re-install pin (L) and clip (M). Tighten

downrod (A) set screws and then tighten nuts.

Slide yoke cover (D) down until it rests on top of

motor housing (E). (Fig. 3)

Ball

Set

Screw

If you decided to cut back the lead wires in Step 4,

strip 1/2 in. of insulation from end of white wire.

Twist stripped ends of each strand of wire within

the insulation with pliers. (Fig. 5) Repeat Step 5 for

black, blue (if applicable) and green wires.

FAN MOUNTING

Install ball end of downrod (A) into mounting

bracket (C) opening. Align slot in ball with tab in

mounting bracket (C). (Fig. 6)

DANGER: Failure to align slot in ball with tab

may result in serious injury or death.

WARNING: To reduce the risk of fire, electrical

shock, or personal injury, wire connectors provided with

this fan are designed to accept only one 12-gauge

house wire and two lead wires from the fan. If your

house wire is larger than 12-gauge or there is more

than one house wire to connect to the two fan lead

wires, consult an electrician for the proper size wire

connectors to use.

CAUTION: Be sure outlet box is properly grounded

and that a ground (green or bare) wire is present.

WARNING: If house wires are different colors than

referred to in the following steps, stop immediately. A

professional electrician is recommended to determine

wiring.

WIRING

Hanging

Ball Slot

Tab

WIRING

DANGER: If using this fan in a DAMP location,

this fan must be connected to a supply circuit that is

protected by a Ground Fault Circuit Interrupter

(GFCI) to reduce the risk of personal injury,

electrical shock or death.

FAN AND LIGHT CONTROLLED BY PULL CHAINS

BLACK

WHITE

GROUND/GREEN (BARE)

WHITE

BLUE

WHITE

FROM FAN

120 V Power

FROM

CEILING

FAN

GREEN

BLACK

GREEN

Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C)

that fits your situation and make appropriate wiring

connections as follows: [NOTE: For each wire

connection below, use one of the wire connectors

(CC) provided, making sure to screw wire

connector (CC) on in a clockwise direction.]

1A. FAN AND LIGHT CONTROLLED BY PULL

CHAINS: Connect BLACK and BLUE wire from

fan to BLACK wire from ceiling. Connect WHITE

wire from fan to WHITE wire from ceiling.

Connect all GROUND (GREEN) wires together

from fan (on downrod (A) and mounting bracket

(C)) to BARE/GREEN wire from ceiling. (Fig. 1A)

WHITE

BLACK

BLACK (WALL SWITCH)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

GREEN

WHITE

GREEN

FAN CONTROLLED BY PULL CHAIN, LIGHT BY

WALL SWITCH

1B. FAN CONTROLLED BY PULL CHAIN,

LIGHT BY WALL SWITCH: If you intend to

control the fan light with a separate wall switch,

connect BLACK wire from fan to BLACK wire

from ceiling. Connect BLUE wire from fan to the

BLACK wire from the independent wall switch for

the light. Connect WHITE wire from fan to WHITE

wire from ceiling. Connect all GROUND

(GREEN) wires together from fan (on downrod

(A) and mounting bracket (C)) to BARE/GREEN

wire from ceiling. (Fig. 1B)

This manual suits for next models

Table of contents

Languages:

Other Harbor Breeze Fan manuals

Harbor Breeze

Harbor Breeze TOWNSEND LP8018LAZ User manual

Harbor Breeze

Harbor Breeze WAVEPORT STYLE E-WK52NWZ5C1 User manual

Harbor Breeze

Harbor Breeze RLG52NWZ5C3L Manual

Harbor Breeze

Harbor Breeze CPW1413 User manual

Harbor Breeze

Harbor Breeze RLG52NWZ5L User manual

Harbor Breeze

Harbor Breeze WINDRISE E-TLEII44BNK5C1 User manual

Harbor Breeze

Harbor Breeze CLASSIC STYLE BDB52LW5N User manual

Harbor Breeze

Harbor Breeze AERO CEILING FAN E-AER52BRZ5LKRCI User manual

Harbor Breeze

Harbor Breeze SHREVEPORT E-NO52AB5C4 User manual

Harbor Breeze

Harbor Breeze 40680 User manual

Harbor Breeze

Harbor Breeze BRISTLE AR13-44BLK AR13-44BN User manual

Harbor Breeze

Harbor Breeze 42612 User manual

Harbor Breeze

Harbor Breeze 40016 User manual

Harbor Breeze

Harbor Breeze MARICOPA LP8013LAZ User manual

Harbor Breeze

Harbor Breeze Casual-3-2011 User manual

Harbor Breeze

Harbor Breeze 00878 User manual

Harbor Breeze

Harbor Breeze FWH60BNK3LRS User manual

Harbor Breeze

Harbor Breeze BDB52BNK5L User manual

Harbor Breeze

Harbor Breeze CLASSIC STYLE BDB52LW5N User manual

Harbor Breeze

Harbor Breeze 00881 User manual

Harbor Breeze

Harbor Breeze BOD52MW3 User manual

Harbor Breeze

Harbor Breeze BUILDER'S SERIES 40698 User manual

Harbor Breeze

Harbor Breeze TIEMPO E-TM52BNK5CS User manual

Harbor Breeze

Harbor Breeze TIEMPO E-TM52BNK5CS User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual