Harbor Breeze 41169 User manual
1
Harbor Breeze®is a registered trademark
of LF, LLC. All Rights Reserved.
ATTACH YOUR RECEIPT HERE
Purchase Date _________________________
ITEM # 1607162, 43105016, 0888516, 43105022
BELLEISLE BAY
CEILING FAN
MODEL #41169, 41172
Français p. 23
RR20002
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
2
TABLE OF CONTENTS
Package Contents .................................................................3
Hardware Contents ................................................................4
Safety Information .................................................................5
Preparation ......................................................................6
Initial Installation ..................................................................7
Standard or Angle Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Closemount Instructions ...........................................................12
Secondary Hanging System ........................................................13
Wiring .........................................................................14
Final Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operating Instructions .............................................................18
Care and Maintenance ............................................................19
Troubleshooting..................................................................19
Limited Lifetime Warranty ..........................................................21
Replacement Parts List ............................................................22
3
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Downrod 1
B Downrod Pin (preassembled to the Downrod [A]) 1
C Downrod Clip (preassembled to the Downrod [A]) 1
D Mounting Bracket (preassembled to the Canopy [E]) 1
E Canopy 1
F Canopy Cover (preassembled to the Canopy [E]) 1
GMotor Assembly 1
H Fitter Plate (preassembled to the Motor Assembly [G]) 1
I Light Kit 1
J Yoke Cover 1
K Blade 3
L Bulb 2
M Glass Bowl 1
N Remote Pack 1
O Phillips-Head Closemount Screw (preassembled to the Motor Assembly [G]) 3
P Mounting Bracket Screw (preassembled to the Mounting Bracket [D]) 4
Q Set Screw (preassembled to the Motor Assembly [G]) 2
R Fitter Plate Screw (preassembled to the Fitter Plate [H]) 3
A
G
F
I
J
Q
R
NM
O
P
K L
H
B
C E
D
4
HARDWARE CONTENTS
Wire Connector
Qty. 6
+ 1 extra
Blade Screw
Qty. 9
+ 1 extra
Blade Washer
Qty. 9
+ 1 extra
Secondary
Support Screw
Qty. 1
Support Washer
Qty. 1
Secondary
Spring Washer
Qty. 1
(shown actual size)
AA BB CC JJ KK MM
5
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
• Before you begin installing the fan, disconnect the power by removing fuses or turning o the circuit
breakers.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-199. Hire a qualied electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the oor and at least 30 in. from the end of the blades to any obstruction.
• The net weight of this fan is: 15.7 lbs.
DANGER: When using an existing outlet box, make sure the outlet box is securely attached to
the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.
WARNING: To avoid personal injury, the use of gloves may be necessary while handling fan
parts with sharp edges.
WARNING: Using a full-range dimmer switch to control fan speed will cause a loud humming
noise from the fan. To reduce the risk of re or electric shock, do NOT use a full-range dimmer switch
to control the fan speed.
WARNING: To reduce the risk of re, electric shock or personal injury, mount the fan to an
outlet box marked “ACCEPTABLE FOR FAN SUPPORT” and use the mounting screws provided with
the outlet box. Most outlet boxes commonly used for the support of lighting xtures are not acceptable
for fan support and may need to be replaced. Consult a qualied electrician if in doubt. Secure the
outlet box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.
WARNING: To reduce the risk of re, electrical shock or personal injury, wire connectors
provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to
the two fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING: To reduce the risk of re or electric shock, do not use the fan with any solid-state
speed-control device or control the fan speed with a full-range dimmer switch.
WARNING: To reduce the risk of re, electric shock or personal injury, do not bend the blade
arms when installing them, balancing the blades or cleaning the fan. Do not insert objects between
the rotating fan blades.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use
of parts OTHER than those provided with this fan will void the warranty.
6
SAFETY INFORMATION
CAUTION: Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.
CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are
secured.
CAN ICES-005 (B) / NMB-005 (B)
CAUTION: This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference and (2) this device
must accept any interference, including interference that may cause undesired operation of the device
(if applicable).
PREPARATION
Before beginning the assembly of this product, ensure that all parts are present. Compare all parts
with the package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Step Ladder, Wire Cutters and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure and Wiring Handbook
7
INITIAL INSTALLATION
1. Turn o the circuit breakers and the wall switch to which
the fan supply line leads.
DANGER: Failure to disconnect the power supply
prior to installation may result in serious injury or death.
2. Determine the mounting method to use.
Standard Mounting is best suited for ceilings 8 ft. or
higher. For taller ceilings you may want to use a longer
downrod (not included).
Angle Mounting is best suited for angled or vaulted
ceilings. A longer downrod is sometimes necessary to
ensure proper blade clearance.
Important: If using the angle mount, check to ensure
the ceiling angle is not steeper than 10°.
Flushmount installation is not available for this item.
Closemount installation is more suitable for ceilings
lower than 8 ft. high.
3. Ensure the blades (K) will be at least 30 in. from any
obstructions. Also check the downrod (A) length to
ensure the blades (K) will be at least 7 ft. above the oor.
1
7 ft.
Minimum
30 in.
Minimum
3
A
K
2
Standard Mounting
Flushmount Closemount
Angle Mounting
8
INITIAL INSTALLATION
4. Loosen all four preassembled mounting bracket
screws (P), then completely remove the two
mounting bracket screws (P) from the round holes
of canopy (E). Set aside for later use.
Detach mounting bracket (D) from canopy (E).
5. Attach mounting bracket (D) to outlet box (not
included) using screws and washers provided with
the outlet box.
CAUTION: It is very important to use the proper
hardware when installing the mounting bracket (D) as
this will support the fan.
5
4
E
D
P
D
D
Standard or
Closemount
Mounting
Angled
Mounting
9
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
1. Remove the downrod clip (C) and downrod pin (B)
from the downrod (A). Then partially loosen the
set screws (Q) in the yoke at the top of the motor
assembly (G).
2. Insert the downrod (A) or a longer downrod, if
required through the canopy (E) and yoke cover
(J). Feed the wires and braided cable from the fan
through the downrod (A).
3. Slide the downrod (A) into the yoke of the motor
assembly (G), align the holes, then re-install the
downrod pin (B) and downrod clip (C). Secure with set
screws (Q) and slide the yoke cover (J) down until it
rests on top of the motor assembly (G).
C
A
B
Q
G
A
J
C
A
J
Q
B
G
E
2
3
1
Yoke
Braided
Cable
10
STANDARD OR ANGLE MOUNTING INSTRUCTIONS
4. Depending on the length of downrod you use, you
may need to cut the lead wires back to simplify the
wiring. If you decide to cut back the lead wires, it is
suggested you do so in the following manner:
• Take the lead wires and make sure you have pulled
them all the way through the top of the downrod.
• Measure 8 inches of lead wire, then cut the excess
wire o with wire cutters (not included).
5. If you decided to cut back the lead wire in Step 4, strip
1/2 in. of insulation from the end of the white wire.
Twist the stripped ends of each strand of wire within
the insulation with pliers (not included). Repeat the
step for black and blue wires.
Note:If you did not cut back the lead wires in Step 4,
Step 5 is not necessary and you may proceed to Step
6 instead.
6. Install the ball end of the downrod (A) into the opening
of the mounting bracket (D). Align the slot in the ball
with the tab in the mounting bracket (D).
Important:The downrod should not rotate if it is
installed properly.
DANGER: Failure to align a slot in the ball with
the tab may cause the fan to wobble or fall, which
could result in serious injury or death.
6
A
D
Tab
Slot
4
8 in.
5
This manual suits for next models
5
Table of contents
Other Harbor Breeze Fan manuals
Harbor Breeze
Harbor Breeze BRADBURY BRD48BNK6LR User manual
Harbor Breeze
Harbor Breeze Santa Ana LP8294LBN User manual
Harbor Breeze
Harbor Breeze EXOCET 40764 User manual
Harbor Breeze
Harbor Breeze PLM52CB5D User manual
Harbor Breeze
Harbor Breeze 40105 User manual
Harbor Breeze
Harbor Breeze WINDRISE E-TLEII44BNK5C1 User manual
Harbor Breeze
Harbor Breeze 35063 User manual
Harbor Breeze
Harbor Breeze L1901 User manual
Harbor Breeze
Harbor Breeze TALAMORE TAL60MBK8LR User manual
Harbor Breeze
Harbor Breeze PORTES LP8293LAZ User manual
Harbor Breeze
Harbor Breeze 00883 User manual
Harbor Breeze
Harbor Breeze 40680 User manual
Harbor Breeze
Harbor Breeze 00878 User manual
Harbor Breeze
Harbor Breeze BTH44ABZC5C User manual
Harbor Breeze
Harbor Breeze 872 User manual
Harbor Breeze
Harbor Breeze BOLTZ 42300 User manual
Harbor Breeze
Harbor Breeze MZ44WW3LR User manual
Harbor Breeze
Harbor Breeze C-TMH44CH5D1R User manual
Harbor Breeze
Harbor Breeze ARMITAGE CC52WW5C1 User manual
Harbor Breeze
Harbor Breeze E-BDB52ABZC5BC4N User manual
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
