Hanna Instruments AquaDip User manual

Instruction Manual

AquaDip

Rugged Waterproof

TDS / °C meter

Manufacturers since 1978 This Instrument is in

Compliance with the CE Directives

SPECIFICATIONS

Range 0 to 1999 ppm

0.0 to 60.0 °C

Resolution 1 ppm

0.1°C

Accuracy ± 2% f.s.

± 0.5°C

Typical EMC ± 2% f.s.

Deviation ± 0.5°C

TDS Factor 0.5

Calibration Factory-calibrated

Temperature Automatic from 0 to 60°C

Compensation β=2%/°C, Tref.=25°C

Battery Type 2 x 1.5V AAA Alkaline

Environment 0 to 50°C; 100% RH

Dimensions 92 x 38 x 450 mm (3.6x1.5x17.7")

Warranty

All Hanna Instruments meters are warranted for two years against defects in workman-

ship and materials when used for their intended purpose and maintained according to

instructions. This warranty is limited to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of prescribed maintenance are not

covered.

If service is required, contact the dealer from whom you purchased the instrument. If

under warranty, report the model number, date of purchase, serial number and the

nature of the failure. If the repair is not covered by the warranty, you will be notified of

the charges incurred. If the instrument is to be returned to Hanna Instruments, first

obtain a Returned Goods Authorization number from the Customer Service department

and then send it with shipping costs prepaid. When shipping any instrument, make sure

it is properly packaged for complete protection.

To validate your warranty, fill out and return the enclosed warranty card within 14 days

from the date of purchase.

Recommendations for Users

Before using this product, make sure that it is entirely suitable for the environment in

which it is used. Operation of this instrument in residential areas could cause interfer-

ence to radio and TV equipment. Any variation introduced by the user to the supplied

equipment may degrade the instrument EMC performance. To avoid electrical shocks,

do not use this instrument when voltage at the measurement surface exceeds 24 VAC or

60 VDC. To avoid damage or burns, do not perform any measurement in microwave

ovens.

05/00 PRINTED IN PORTUGAL

Dear Customer,

Thank you for choosing a Hanna product.

Please read this instruction manual carefully before using the

instrument.

This manual will provide you with the necessary information

for a correct use of the instrument, as well as a precise idea of

its versatility.

If you need additional technical information, do not hesitate to

e-mail us at [email protected].

These instruments are in compliance with directives

EN 50081-1, EN 50082-1 and EN 61010-1.

TAKING MEASUREMENTS

The meter is factory calibrated for ppm and temeprature.

Press the ON/OFF key to turn

the meter on.

Immerse the probe into the so-

lution to be tested. The water

level must be above the hole

on the sleeve. If possible, tap

the probe to remove any air

bubbles that may be trapped

inside.

Allow for the reading to stabi-

lize. The LCD displays the

ppm reading.

Press the RANGE key to view

the temperature reading.

Press RANGE again to return

to ppm reading.

If the ppm reading is out of range, the “

---

” indication

is displayed. If the temperature reading is out of range,

the “°C” symbol blinks.

HOLD FUNCTION

To freeze the current measure-

ment on the LCD, press and

hold the RANGE/HOLD key for

about 3 seconds.

When the hold function is active, the LCD displays

alternatively the “HLd” indication and the frozen read-

ing.

Press RANGE to switch from ppm to temperature read-

ing.

Press the ON/OFF key to exit the hold mode and

return to normal operation.

BATTERY REPLACEMENT

To prolong the battery life, the meter switches itself off

after 5 minutes of non-use.

Variations in readings or fading display can indicate

weak batteries.

If the batteries are too weak to support proper opera-

tions, the LCD displays the message “Eb” and then the

meter switches itself off.

Battery replacement must only take place in a non-

hazardous area using AAA-type 1.5V, alkaline batteries.

In order to replace run down

batteries, simply remove the

two screws on the bottom

cover and replace the two 1.5V

AAA batteries with new ones,

paying attention to the correct

polarity.

New batteries allow approx. 1000 hours of continuous

use (with 1175mA/h batteries).

Other Hanna Instruments Measuring Instrument manuals

Hanna Instruments

Hanna Instruments HI 991300 User manual

Hanna Instruments

Hanna Instruments HI 9829 User manual

Hanna Instruments

Hanna Instruments HI 96721C User manual

Hanna Instruments

Hanna Instruments HI705 User manual

Hanna Instruments

Hanna Instruments HI 83200 User manual

Hanna Instruments

Hanna Instruments HI96719C User manual

Hanna Instruments

Hanna Instruments HI97710 User manual

Hanna Instruments

Hanna Instruments HI981400 User manual

Hanna Instruments

Hanna Instruments edge EC HI2003 User manual

Hanna Instruments

Hanna Instruments HI96702C User manual

Hanna Instruments

Hanna Instruments IRIS HI801 User manual

Hanna Instruments

Hanna Instruments HI 758 User manual

Hanna Instruments

Hanna Instruments HI 96821 User manual

Hanna Instruments

Hanna Instruments PCA 300 Series User manual

Hanna Instruments

Hanna Instruments HI 4109 User manual

Hanna Instruments

Hanna Instruments HI 9219 User manual

Hanna Instruments

Hanna Instruments HI 721 User manual

Hanna Instruments

Hanna Instruments HI762 User manual

Hanna Instruments

Hanna Instruments HI 96762 User manual

Hanna Instruments

Hanna Instruments HI 8730 User manual

Hanna Instruments

Hanna Instruments HI 121 User manual

Hanna Instruments

Hanna Instruments HI9813-51 User manual

Hanna Instruments

Hanna Instruments HI 2210 User manual

Hanna Instruments

Hanna Instruments HI761 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual