Haier HLP141E User manual

User Manual

Model HLP141E, HLP140E

Guide de l’Utilisateur

Modéle HLP141E, HLP140E

Manual del Usuario

Para Modelo de HLP141E, HLP140E

Electric Vented Tumble Dryer

Sécheuse Électrique Ventilée

Secadora eléctrica de ropa con

ventilación

Grounding Instructions:

This appliance must be grounded. It is equipped with a 3-wire cord having

a grounded plug. The plug must be plugged into an outlet which is properly

installed and grounded

Warning – Improper use of the grounded wire can result in the risk of electric

shock. Consult a qualified electrician if necessary. Do not attempt to defeat this

safety feature by modifying the plug. Avoid the use of an extension cord because

it may overheat and cause a risk of fire. However, if it is necessary to use an

extension cord:

A. Use only 3-wire extension cord with 3-blade grounding plug.

B. The marked rating of the extension cord must be equal to or greater than the

rating of this appliance.

Attempting any maintenance or cleaning:

To minimize the possibility of electric shock, unplug this appliance from the power

supply or disconnect the dryer at the household distribution panel by removing

the fuse or switching off the circuit breaker before attempting any maintenance or

cleaning (except the removal and cleaning of the lint filter).

NOTE: Pressing the Power ON/OFF button to an off position or pressing Start /

PAUSE button, does NOT disconnect the appliance from the power supply.

English

ELECTRICAL REQUIREMENTS

WARNING!

Avoid fire hazard or electric shock. Do not use an extension cord or an

adapter plug. Do not remove any prong from the power cord.

English

Front

Back

PARTS AND FEATURES

Cycles

Dry

Time

Temp

Start

Pause

Power

On/Off

Dry

Cooling

End Cycle

Clean Lint

Normal

Timed Dry

Heavy

Delicate

120

High

Low

Air-Dry

150

Status

HLP141E

Drum

Windows

(HLP141E Only)

Exhaust and Lint Filters

Door

Door Gasket

Air Intake

Digital Control Panel

Dryer Hanging Wall Hook

Power Cord Exhaust Vent

Hose Clamp Exhaust Housing

Casing Back Cover

Spacer

English

SET UP INSTRUCTIONS

Tools and Parts Required for Installation:

Philips Head Screw Driver•

Flat Head Screw Driver•

Electric Drill and 1/8 inch drill bit•

Stud finder (optional)•

(6) Wood screws for mounting plywood•

Plywood board; size 30 (h) by 24(w) inches or wood slats•

Venting materials:

4 inch diameter metal exhaust rigid ducting and fittings or UL flexible metal•

dryer vent hose, that should not exceed 6 feet.

2 additional hose clamps for ducting outside exhaust vent hose•

Metal Elbows or outdoor vents as needed.•

Location of Your Dryer

First find a suitable location where you can mount the dryer on the wall and still

have access to 120 Volt outlets and exterior venting.

Type: Electric dryer

Rating: Please refer to the rating label regarding detailed information

Size: 26.97x24.8x16.73(inch)

Capacity: 2.6 cu.ft.

Weight: 52.9lbs(24kg)

Check dryer size and ensure a good location for the dryer installation on a•

wall where you can mount the unit using wall studs or beams.

It is recommended to use a plywood board (30 by 24 inches) to mount the•

dryer using the walls beams and studs as support, rather than just wood slats.

Make sure the dryer power cord can reach a 120 Volt outlet.•

Make sure you can connect the exhaust vent to the outside or designated•

dryer vent (in a laundry room).

The length of exhaust ducting should not exceed 6 feet.•

Please read the additional ducting information and warnings in this manual.•

16.73”

26.97”

24.8”

Vent to outside Nearest 120 Volt

AC outlet

English

Assemble Dryer for Installation

Screw mounting hook bracket and wall spacer to dryer with screws provided.

1. Attach Hanging hook bracket

using the 4 screws.

3. Attach Exhaust Housing. Connect vent housing to dryer using hose clamp

provided to the exhaust pipe.

4. You have two choices of the exhaust pipe housing direction.

2. Attach the 2 wall spacers to the bottom

of the dryer, using the 2 screws.

Spacers

Exhaust Vent Housing

Hose Clam

Exhaust Pipe

English

Venting The Dryer

Proper venting of the dryer is very important. Determine the best and safest

ducting for the dryer.

Exhaust Requirements and Maintenance.

Clothes dryer installation must be performed by qualiﬁed installer.1.

Install the clothes dryer according to the manufacturer’s instructions and local codes.2.

Do not install a clothes dryer with ﬂexible plastic venting materials. If ﬂexible metal3.

(foil type) duct is installed, it must be of a speciﬁc type identiﬁed by the ﬂexible duct

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airﬂow and increase the risk of ﬁre.

Clean old ducts before installing this dryer.4.

WARNING!

Outside

Vent

Correct Incorrect

Venting must conform to local building codes.•

Do not use thin plastic or foil ducting.•

Use 4 inches (10.2cm) diameter rigid or flexible metal duct (note: venting•

materials are not supplied with the dryer, and you should obtain the venting

materials necessary for proper installation at your local hardware store).

Position the Dryer such that the exhaust duct run is as short as possible.•

Make sure there is no more than 6 feet of exhaust ducting.

Clean old ducts before installing this dryer•

Never bend or collapse ducting flex hose. Use few elbows joints as needed.•

Use duct tape on all duct joints.•

Insulate ductwork that runs through unheated areas in order to reduce•

condensation and lint build-up on pipe walls.

To reduce the risk of fire and combustion, the dryer must be vented outdoors. Lint

accumulation can cause fires. Check and clean vents and ducting as often as possible.

PLEASE BE AWARE THAT FAILURE TO EXHAUST THE DRYER CORRECTLY WILL VOID THE

DRYER’S WARRANTY.

English

INSTALLATION INSTRUCTIONS

Location for installation and options for various walls

1. There are 2 mounting options- either using wood slats or a whole plywood

board. The dryer installation to the wall should be able to accommodate the

weight of the unit of 52 lbs. plus about 10 lbs. for clothing (or approximately

62 lbs). We suggest you use a plywood board for added support and safety,

this is the best way to mount.

2. Determine dryer position on the wall. A minimum of 6”(Inches) is needed

between the top of the dryer and the ceiling for installation.

3. If mounting the dryer above a washing machine, allow sufficient space to

open the top lid of the washer.

4. The Best installation is to add a plywood board to the wall studs. As a

second option- you can use two (2) slats (2 by 4 “) and attach to studs.

English

Wall Mounting Instructions

5. For the best installation

Locate the wall studs in order to securely mount the unit on the wall. Use 1

plywood board size 30 (h) by 24(w) inches and mount into the wall studs

using (6) wood screws (not provided)

6. Mark the required dryer bracket position and holes using the template provided.

7. Using the 4 supplied screws attach the 2 wall hanging mounting brackets onto

the plywood. The distance between each bracket should be 6” apart.

Use wood screwsPlywood board

for supporting

the dryer

24 inches

30 inches

Stud

HLP141E Mounting template

Center and level template

6 inches

Mounting

bracket

Mounting

bracket

Drill holes for dryer

mounting bracket

6 inches

You are now ready to hang the dryer to the wall.

English

8. Hanging dryer on wall

Lift the dryer (with the help of an assistant) and insert the hanging hook onto

the 2 mounting brackets on the wall. The wall spacer will distance the dryer

from the bottom.

Completing Installation

9. Connect ducting to the dryer

Connect the exhaust ducting (not provided) from the dryer venting housing to

external outside dryer vent using a hose clamp (not provided).

10. Competed final installation, on wall with ducting.

Hang dryer onto

mounting brackets

on the wall

Note Must purchase these parts from local hardware store.

hose clamp

Exhaust Ducting

hose clamp

Outside

Vent

Exhaust

Housing

Outside Vent

Note

Vent to the outside only. Improper taping

to vent or unstable installation to vent will

cause undesirable drying performance.

Other manuals for HLP141E

This manual suits for next models

Table of contents

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions