Haier HDY-E60 User manual

Extra Dry

100min

30min

60min

30min

INNOVATIVE DESIGN

HDY-E60

number of the tumble dryer.

1 Read all instructions before using this dryer.

2 The interior of the dryer should be cleaned periodically by qualified service

personnel. An excessive amount of lint build up in the interior of the dryer could

result in inefficient drying and pose a possible fire hazard.

3 The appliance must not be installed behind a lockable door, a sliding door or a door with

a hinge on the opposite side to that of the tumble dryer in such a way that a full opening

of the tumble dryer is restricted.

4 Attention - rear panel can be hot.

5 The tumble dryer should not be used if industrial chemicals have been used to

6 The dryer must only be used for its intended purpose.

7 Clean lint screen before or after each load.

8 This appliance is not intended for use by people (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Young children should be

supervised to ensure that they do not play with the appliance.

9 Do not operate the dryer if any parts are missing or broken.

10 To avoid fire hazard or electrical shock do not use an adaptor plug or extension

cord or remove grounding prong from electrical power cord. Failure to follow this

warning can cause serious injury, fire or death.

11 To avoid fire hazard or electrical shock do not reach into the drum while the drum is

12 Do not attempt to modify or repair the controls.

13 The final part of a tumble dryer cycle occurs without heat (cool down cycle) to cool

items to a temperature that ensures that they will not be damaged. Never stop a

tumble dryer before the end of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated.

14 Do not dry items that have been previously cleaned in, washed in, soaked in, or

spotted with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot

removers, turpentine,waxes and wax removers, etc. Do not store or use these items

on or in the vicinity of the dryer. Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may contribute to a chemical reaction that

could cause a load to catch fire. Oil-affected items can ignite spontaneously, especially

when exposed to heat sources such as in a tumble dryer. The items become warm,

causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot

escape, the items can become hot enough to catch fire. Piling, stacking or storing

oil-affected items can prevent heat from escaping and create a fire hazard. If it is

unavoidable that fabrics that contain vegetable or cooking oil or have been

contaminated by hair care products be placed in a tumble dryer they should first be

washed in hot water with extra detergent - this will reduce, but not eliminate, the

hazard.

moving. Wait until the dryer has stopped completely before reaching into the drum.

clean the dryer.

15 Do not dry unwashed items in the tumble dryer.

16 Fabric softeners, or similar products, should be used as specified by the fabric

softener instructions.

17 To prevent fire, do not use heat to dry items containing plastic, foam rubber or

similarly textured rubber-like materials, or items containing feathers or down. Items

such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed

articles and clothes or pillows fitted with foam rubber pads should not be dried in the

tumble dryer.

18 This dryer must be properly installed in accordance with the installation instructions

before it is used.

19 Do not install or store this dryer where it will be exposed to water and /or the weather.

Keep surrounding areas free from the accumulation of lint, dust and dirt.

20 To prevent shock hazard and assure stability during operation, the dryer must be

installed and electrically grounded by a qualified service person in accordance with

local codes.

21 Do not sit on top of the dryer.

22 If the power cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

23 Always disconnect dryer from electrical supply before attempting any service.

Disconnect power cord by grasping the plug, not the cord.

24 Do not repair or replace any part of the dryer or attempt any servicing unless

specifically recommended in the user-maintenance instructions.

25 Before the dryer is removed from service or discarded, remove the dryer door to

prevent accidental entrapment.

INSTALLATION INSTRUCTIONS

FREE STANDING

INVERTED WALL MOUNTING

STACKING INSTALLATION 11

CHANGE THE VENTING MODE 12

INSTALL THE FLEXIBLE HOSE 13

Caution, risk of fire - this is a safety symbol. Failure to follow the warnings

outlined in these user instructions can cause a fire hazard.

26 Remove all objects from pockets such as lighters and matches.

Extra Dry

100min

30min

60min

30min

Read all instructions before using this dryer.

This dryer has been designed for domestic use only.

SAVE THESE INSTRUCTIONS.

This diagram may be slightly different from the layout of the dryer you

have just purchased due to technical improvements.

Power supply cord Model number

and Serial number

Back plate

Air intake grill

Outlet cover

Control panel

Door

Program selector

Exhaust grill

Lint filter

Top panel

Door switch

Attention:

1.Before operation, clean off any dust and dirt inside the drum of the dryer with a damp

towel.

2.Clean off any debris on the lint filter and in the duct to increase the drying efficiency.

Turning on power

Before turning on the power of the dryer check whether the supply voltage is in

accordance with the value indicated on the name plate.

Preparation of laundry load

- The dryer can only dry laundry which has been spun dry. Do not put in laundry which

is still dripping wet or has excess water.

- Make sure all pockets are empty before placing laundry in the dryer.

- Pull up zippers, mend loosened fasteners and tie up ribbons to prevent the

laundry from being entangled. If necessary,put small items in a laundry bag.

- To achieve a better drying result ensure the clothes are separated before loading into the

dryer.

Load to dry

Laundry type Cotton fabric Synthetic fabric

Maximum load 6 kg 3 kg

Warning：

1. Avoid drying wool, silk and other

delicate fabrics, they maybe

damaged.

2. Do not exceed the recommended

load limit. This could damage the

dryer as well as the laundry.

1. Power up

Insert the power plug into an appropriate power outlet that is properly installed and

grounded. Operating power supply: 220-240V~50Hz.

2. Laundry loading

Open the door and load the laundry into the drum of the dryer. For a more energy

efficient and better drying result, make sure the load has been spun dry. Try to

loosen the load when placing in the dryer.

Note: Check labels on clothing before placing them in the dryer. Some articles are not

suitable for machine dry. High temperature may damage the fabric.

3.Setting drying program

Turn the program knob to set your desired drying program.

5. Program operation

After a program is set, gently touch the “START/PAUSE” button to start the program.

6. Program completion

After the program is complete, the dryer will stop tumbling and the display screen will

display “End”. Open the door and remove the laundry.

7. Turning off the dryer

Turn the program knob to the “OFF” position and turn the power off at the wall.

Note: Clean the filter after each load.

May be tumble dry .

Do not tumble dry .

Normal dry .

Air dry, only .

If the laundry is not removed, the dryer will automatically commence an "anti-crease"

protection cycle to keep your laundry from settling in one position and creasing. This

cycle will last an hour unless stopped. The dryer will run with cool air at set intervals.

4.Delay setting.

You may choose to start the dryer after a preset time.

The delay range is between 0.5 and 24 hours.

To stop the anti-crease cycle press the start/pause button or open the door, empty

the dryer and turn off as shown below.

Drum reversal: The dryer is designed to rotate in each direction, clockwise and

anti-clockwise in a certain period to minimize tangling and ensure clothes dry

efficiently.

Extra Dry

100min

30min

60min

30min

A - Program control knob

D - Start/Pause button

F - Indicator light

E - Program setting

Heat Dry

Extra dry*

Normal**

A DE

Sensor Program

The drying time will depend on the type of fabric.

The maximum time is 4 hours. Choose the program

according to the type of fabric.

Timed Program

100 min 100 minute timed drying cycle, choose the program

according to the type and weight of the fabric.

60 min 60 minute timed drying cycle, choose the program

according to the type and weight of the fabric.

30 min 30 minute timed drying cycle, choose the program

according to the type and weight of the fabric.

The dryer will automatically switch off the heater at the end of every heat drying cycle

and start a cool down phase. This is important as it removes the stored heat from the

laundry and helps prevent creasing.

Air dry

60 min 60 minute timed cool air cycle, no heat applied.

30 min 30 minute timed cool air cycle, no heat applied.

*) AS/NZS 2442.2 test program setting.

**) EN61121 test program setting.

B - Delay button

You may choose to start the dryer after a preset time. The delay range is between

0.5 and 24 hours. Gently touch the delay button before a program starts, each touch

will add one hour. When in excess of 24 hours, the remaining time will be re-displayed.

After a delay time is set, touch the Start/P ause button to start the delay operation

and the indicator light will flash.

C - LED screen

This screen displays the remaining time for a program and the delay time.

After turning on the power, select the drying program you desire.

Gently touch Start/Pause button to start the dryer. To Pause a program gently touch

this button during the operation of the dryer. The display screen will flash and the

machine will be halted.Press the Start/Pause button again and the program will

continue to operate.

WARNING! Unplug the power cord prior to any cleaning

Cleaning the surface

Wipe off any dust or dirt.

Note: Do not use excessive water,. a damp cloth is fine.

Do not use solvent.

Do not use spray cleaners when cleaning the interior.

Do not use harsh or abrasive cleaners.

Cleaning the filter screen

To ensure good ventilation during drying, the filter screen must be cleaned before

or after each use.

1. Remove the filter

Gently pull out the filter screen towards yourself.

2.Cleaning the filter

Remove the lint with a soft brush or vacuum

cleaner. Be careful not to damage the filters.

Remove any remaining lint from the lint screen

on the door.

3. Re-installing the filter

After cleaning filters, put the screen back in place.

Note: Never operate your dryer without the lint filter.

Remove the transport packaging (fig.1)

Remove the tape on the door (fig.2), the wall mounting kit and the inverted panel

film attached to the inside of the drum (fig.3) before starting the dryer.

Packing accessories

Check list of the accessories and materials provided with the machine:

To ensure the dryer operates normally, attention must be paid to the

following:

1. The rear of the dryer must not have any restriction to the intake of fresh

air.

fig.1 fig.2

Dimensions

a=830 mm

b=600 mm

c=560 mm

Weight=30 kg

INSTALLATION INSTRUCTIONS

2. Check the dryer for any damage. If any damage is found do not operate

and contact your supplier or Authorised Service Centre.

3.The dryer must be kept away from flammable substances.

4.The surrounding environment must be dry and ventilated.

5. For best results,the ambient temperature should be between 10

and 35 .

fig.3

Name Quantity

User manual 1

Wall mounting kit 1

Inverted panel film 1

Flexible hose 1

Flexible hose clip 1

Hose connector 1

Unpacking your dryer

Stacking kit 1

ExtraDry

100min

30min

60min

30min

INSTALLATION INSTRUCTIONS

Tools required

For plaster/ Drill & 3mm Bit 1

Wooden wall Philips head screwdriver

Wall mounting kit includes

Plastic spacers 2

Wall hanging brackets 2

Hanging hook 2

Wood screws, 12gx50mm 4

Screws for hanging hooks 6

and plastic spacers.

Description

Free standing

The dryer stands on the floor and can easily be moved into position. Ensure

that it is placed on a level floor. Also ensure there is at least 50 mm air

clearance between the back of the dryer and the wall to allow fresh air flow

for efficient operation.

Attention:

Please don’t put a heavy

load on the dryer’s top panel,

such as a basket full of

wet laundry

Inverted wall mounting

The dryer can be mounted on the wall in the inverted position only by following

these instructions.

Invert the dryer so that the control panel is at the bottom (see figure 4) this

allows easier access to the controls.

1. Determine the location of the dryer on the wall and mark the bracket

position.

A minimum 50 mm is needed between the top of the dryer and the ceiling

for ease of installation;

If mounting above a washing machine, allow sufficient room to open the lid

of the washer.

Minimum lid

clearance

ExtraDry

100min

30min

60min

30min

Table of contents

Other Haier Dryer manuals

Haier

Haier HDY-C70 WH HA AA User manual

Haier

Haier HDY60M User manual

Haier

Haier Genesis CRDE200AW User manual

Haier

Haier HD100-A2979 User manual

Haier

Haier HD90-A636 User manual

Haier

Haier GE GFD14ESSNWW How to use

Haier

Haier ProSoft User manual

Haier

Haier HDY-HMS70 User manual

Haier

Haier HMS6-1 User manual

Haier

Haier CG700AW User manual

Haier

Haier HLTD500AGW User manual

Haier

Haier RDE350AW - 6.5 Cu. Ft. Electric Dryer User manual

Haier

Haier HDY-D70-E User manual

Haier

Haier HDY-D70-E User manual

Haier

Haier QFT15 Series Original instructions

Haier

Haier GDZ607VA User manual

Haier

Haier HDY5-1 User manual

Haier

Haier GDE480BW User manual

Haier

Haier HLP140E - 2.6 cu. Ft. Portable Vented Electric... User manual

Haier

Haier HD90-A2979 User manual

Haier

Haier HDY6-1 User manual

Haier

Haier HDY6-1 User manual

Haier

Haier GDZ22-1 User manual

Haier

Haier QFT15ESSNWW Original instructions

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions