Hach WDMP sc User manual

DOC026.97.80326

WDMP sc

08/2019, Edition 2

User Manual

Manual del usuario

Manuel de l’utilisateur

Table of Contents

English..............................................................................................................................3

Español.......................................................................................................................... 24

Français......................................................................................................................... 48

Table of Contents

1 Specifications on page 3

2 General information on page 4

3 Installation on page 9

4 Startup on page 18

5 Operation on page 19

6 Maintenance on page 19

7 Troubleshooting on page 22

8 Replacement parts and accessories on page 22

Section 1 Specifications

Specifications are subject to change without notice. The specifications that follow are for the junction

box (Table 1) and the WDMP sc panel (Table 2). Refer to the instrument user manuals for the

analyzer, controller, turbidimeter and probe sensor specifications.

Table 1 Junction box

Specification Details

Power requirements 100 to 115/230 VAC, 50/60 Hz

Power consumption 90 VA maximum for CL17 analyzer

24 W maximum for all other electronics

Protection class I

Installation category II

Pollution degree 2

Altitude 2000 m (6562 ft) maximum

Fuse 5 x 20 mm, T 1.0 A, 250 V (2x)

Storage temperature –20 to 60 °C (–4 to 140 °F)

Conduit hub ½ NPT

Communications RS485 Modbus

Humidity Maximum relative humidity 80% for temperatures to 31 °C (88 °F), decreasing linearly to

50% relative humidity at 40 °C (104 °F)

Table 2 WDMP sc panel

Specification Details

Dimensions (W x H x D) 81 x 122 x 30.8 cm (32 x 48 x 12.1 in.)

Weight 54.4 kg (120 lb)

Operating temperature 5 to 40 °C (41 to 104 °F)

Sample flow rate 0.4 to 0.6 L/min

Sample pressure 138 to 862 kPa (20 to 125 psi)

Sample temperature 5 to 40 °C (41 to 104 °F)

Sample inlet connection ½-in. OD tube

Sample waste drain connection ¾-in. ID hose barb

Sample waste drain pressure Ambient, free-flowing (atmospheric)

Pressure sensor Stainless steel (17-4 PH), Input: 7–35 VDC; Output: 4–20 mA, 0–1034 kPa

(0–150 psi)

English 3

Table 2 WDMP sc panel (continued)

Specification Details

Certifications ETL listed to UL and CSA standards

Warranty 1 year

Section 2 General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

2.1 Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

2.1.1 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

2.1.2 Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential

injury. If on the instrument, refer to the instruction manual for operation or safety information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

4 English

This symbol indicates the need for protective eye wear.

This symbol indicates that the marked item requires a protective earth connection. If the instrument is

not supplied with a ground plug on a cord, make the protective earth connection to the protective

conductor terminal.

This symbol, when noted on the product, identifies the location of a fuse or current limiting device.

This symbol indicates a laser device is used in the equipment.

This symbol indicates elevated, potentially dangerous, levels of non-ionizing radiation.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

2.1.3 Chemical and biological safety

D A N G E R

Chemical or biological hazards. If this instrument is used to monitor a treatment process and/or

chemical feed system for which there are regulatory limits and monitoring requirements related to

public health, public safety, food or beverage manufacture or processing, it is the responsibility of the

user of this instrument to know and abide by any applicable regulation and to have sufficient and

appropriate mechanisms in place for compliance with applicable regulations in the event of

malfunction of the instrument.

2.2 Certification

CAUTION

This equipment is not intended for use in residential environments and may not provide adequate protection to

radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, ICES-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

English 5

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

2.3 Product overview

The Water Distribution Monitoring Panel sc (WDMP sc) is an assembly of instruments that monitor

the water quality in a distribution system. The instruments are mounted on a panel with the electrical

and plumbing connections installed. The instruments measure chlorine, conductivity, pH, ORP

(optional), turbidity, pressure and temperature. A controller sends the data to a communications

network for remote monitoring. Refer to Figure 1 for the WDMP sc with the CL17 chlorine analyzer or

Figure 2 for the WDMP sc with the CLF10 or CLT10 chlorine analyzer.

6 English

Figure 1 WDMP sc overview—CL17 chlorine analyzer

1 Inductive conductivity probe option 7 Standpipe and sample manifold

2 Turbidity sensor 8 Standard conductivity probe

3 Service bracket 9 Pressure sensor

4 CL17 chlorine analyzer 10 Sample flow valve

5 Junction box 11 Drain manifold

6 Controller

English 7

Figure 2 WDMP sc overview—CLF10 or CLT10 chlorine analyzer

1 Inductive conductivity probe option 7 CLF10 or CLT10 gateway

2 Turbidity sensor 8 Standpipe and sample manifold

3 Service bracket 9 Standard conductivity probe

4 CLF10 or CLT10 flow cell 10 Pressure sensor

5 Junction box 11 Sample flow valve

6 Controller 12 Drain manifold

2.4 Product components

Make sure that all components have been received. Refer to the list that follows. If any items are

missing or damaged, contact the manufacturer or a sales representative immediately.

•WDMP sc panel—Refer to Figure 1 on page 7 or Figure 2 on page 8.

•Startup kit for WDMP sc—Refer to Figure 3 and the list that follows.

8 English

• Tubing, ½-inch OD (10 ft)

• Tubing, 1-inch OD (10 ft)

• Cable assembly, 1-m probe extension

• Clamp, hose worm drive

•CL17 analyzer kit (if applicable)—Refer to CL17 analyzer kit on page 9.

Figure 3 Reagents for WDMP sc startup kit

1 CL17 analyzer reagents (if applicable) 4 Conductivity standard solution

2 pH buffer solutions—pH 4, 7 and 10 5 19.2 N H2SO4 for CL17 (if applicable)

3 20 NTU Stablcal standard solution 6 20 NTU Stablcal standard solution, sealed vial with

RFID tag

CL17 analyzer kit

Refer to the list that follows for the items in the CL17 analyzer kit.

• Pinch plate and thumb screws (2x)

• Stir bar, micro

• Filter, 40 mesh SST

• Funnel

• Tubing harness (3x)

• Tube, 11/16-inch OD x 1/2-inch ID, 1.025 ft

• Tubing, 0.193-inch OD, 2.333 ft

• Fitting, barb (5x)

• Fitting, elbow

• Hose clamp

• Seal, quad ring

Section 3 Installation

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

3.1 Mechanical installation

WARNING

Personal injury hazard. Make sure that the wall mounting is able to hold 4 times the weight of the

equipment.

English 9

WARNING

Personal injury hazard. Instruments or components are heavy. Use assistance to install or move.

This instrument is rated for an altitude of 2000 m (6562 ft) maximum. Use of this instrument at an

altitude higher than 2000 m can slightly increase the potential for the electrical insulation to break

down, which can result in an electric shock hazard. The manufacturer recommends that users with

concerns contact technical support.

Attach the panel on a flat, vertical wall surface in an indoor location away from direct sunlight. Install

the instrument in a location and position where the user can easily disconnect the instrument from

the power source. Refer to Figure 4 for product dimensions. Refer to Figure 5 to attach the panel to a

wall. Mounting hardware is supplied by the user.

Figure 4 Product dimensions

1 Buffer area

10 English

Table of contents

Languages:

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual