Gasmet GT5000 User manual
Gasmet Technologies
Tel : 1-866-685-0050
1
OPERATING GT5000 TERRA
FTIR GAS ANALYZER
QUICK GUIDE
Check the GT5000 & Calcmet manuals for full user instructions
or contact local representative or Gasmet
Requires that the Hazmat Application Library located in the folder C:\Identification
Tool _ SNxxxxx has been loaded into the Calcmet EASY or EXPERT software
Advanced Test Equipment Corp.
www.atecorp.com 800-404-ATEC (2832)
GT5000 Terra Portable FTIR multi-gas Analyzer
Components
2
Gasmet USB Stick –All manuals,
software and documentation
And HASP Keys
Gasmet Sample Probe with
1. Teflon Tubing (white) recommended for sampling
2. Tygon tubing (Clear) recommended for
background measurement
AC Power Pack
Li-ion Battery
GT5000 Terra
Gasmet Tablet
3
BATTERY HATCH & POWER CONNECTION
Door Closed
Battery
AC Power inlet
~ 3Hrs. Battery Life & 4 Hrs. Recharge time
4
Quick connections for gas
lines
•Purge air in
•Sample out
•Sample in
•Zero gas in
USB Cable port Power button & sets mode of
communication with Tablet
Battery status indicator
1. Remove rubber dust protection from GT5000 front panel
2. Apply Power
3. Attach Sample Connector (Tubing & Probe) to Sample In
4. Turn the Power Button to the desired communication mode
5. Open Calcmet on Tablet (or laptop)
GT5000 Front Panel
GT5000 & Calcmet EASY Communication Settings
5
1. Turn Control switch to communication mode
- Cable
- Wifi
- Bluetooth (default)
2. In Calcmet EASY
Choose the GT5000 Mode of Operation
1
2
GT5000 Setting
Calcmet EASY Setting (no action required unless troubleshooting a communication issue)
Default setting is Bluetooth
Running Calcmet™EASY on Gasmet Tablet 6
1. Turn on Tablet
2. Double Tap Calcmet Icon with Stylus or Finger
3. Wait 10-20 secs for Calcmet EASY screen
(last application library used will automatically load _ Default is Hazmat_Application)
Calcmet EASY Software
7
Five different screens available
(each screen is separate not as shown above)
Views
Results
Spectrum
Trend
Residual
Background
Left & Right arrows
move between
screens
Click Hardware
Checks that the analyzer is ready to measure
‘Hardware status is OK’ is displayed
if analyzer is ready to measure.
If ‘Hardware status is Not OK’ is displayed
Click on Details. Contact Gasmet or
representative if Status ‘OK’
cannot be displayed after waiting further
warm-up time.
8
If error occurs after clicking Hardware, check settings according to slide
“GT5000 & Calcmet EASY Communication Settings “
Check Hardware Status
Verify GT5000 is functioning correctly 9
1. Connect the sampling line with probe to the Sample IN port on the analyzer front panel.
2. One single measurement where the pump is not activated can be taken by clicking or
3. Start a continuous measurement where pump is automatically started by clicking
4. Continuous measurement starts, and results are
updated to the screen at end of each cycle.
5. Check that OK is displayed
10
Background measurement
1. Connect 5.0 purity nitrogen (N2) gas to Zero gas inlet on the
analyzer front panel. Depending on the regulator for the zero
gas bottle following flush times are recommended.
2. Flush Time setting (Menu →Measuring Times)
When (N2) gas flow is 1 - 3 l/min set Flush time = 120 (secs)
3. Click Background .
The GT5000 will automatically proceed to the perform
background. Time clock will show Flush Time then count down
the preset 3 mins background time. At completion of
background a new screen as shown next page will be
displayed.
Immediately Turn off Nitrogen zero gas.
Table of contents
Other Gasmet Measuring Instrument manuals
