Foryou TPMAI1DIC1 User manual
TPMS USER MANUALTPMS USER MANUAL
Caution:
NOTE:
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation
Thank you for choosing products. Please carefully read
the manual, you will learn to use all the functions of the new tire pressure
monitoring system
*
TPMAI1DIC1
USER MANUAL
This product is applicable to passenger cars
*
Contents
Precautions
Contents
Product description
Installation
Troubleshooting
Operation
Equipment connection
1
2
3
Transmitter installation steps
4
Receiver installation steps
5
System introduction
6
System settings
Backlight settings 7
14
16
18
17
Disclaimer
Common alerting mode
Precautions
Before using this product, please be sure to have read the <User Manual>
Precautions
This product is applicable to 12V cathode
grounding battery system car, please do not install
the product in 24V truck or bus.
Do not install the product in the field of impacting
driver's vision or driving operation.
In order to avoid traffic accidents caused by
decentralizing driver's attention, please do not
operate the product while driving. If there is
operation need, please park your car in a safe
place.
Do not expose the product in the over-moist
environment or let it touch water, otherwise they will
lead to electrical short circuit damage
Avoid the strong impact on the product,otherwise it
will damage the structure components of the
product.
Do not open the product crust or adjust any other
parts oneself.If there is a service need ,please go
to a professional repair service center for
consultation.
1
1
3
4
5
6
12V
24V
2
This product provides one-year free warranty, If there is quality
problem,please contact with local dealers. Man-made factors
such as incorrect installation, improper use,contacting with
harmful substances damage are not in the warranty list, please
keep your warranty card and certificate well for servicing.
2
Product Description
1
2
3
1
4
1
-40 ~ 105℃℃
≤95%RH
73×67×20mm
Normal use>6 years
0kPa~800kPa
-30 ~ 70℃℃
433.92MHz
130×40×45mm
DC 12 4V
433 92MHz.
Product Description
Composing component
Tire Pressure Monitoring System includes the following components:
SN. Name Icon Amount
Receiver
Transimitter
Paste board
Product technical specifications
Operating humidity
Product Size
Product life
Pressure measuring range
Receive frequency
Transimitter frequency
Operating temperature
Receiver
Operating temperature
Operating hvoltage
Product Size
Transimitter
Installation
3
Installatio
1
2
3
4
jacket nut
sensor
protective cap
flat washer
rubber washer
5
6
Transmitter installation steps:
remove tires from the car, remove the rubber tire after the tires
were deflated
clean the rim
Screw the protective cap, jacket nut, flat washer from the
transmitter to be installed.
Insert sensor into the corresponding location of the tire valve,
and then be fixed by jacket nut.
Pay attention to avoid the location of transmitters when install
rubber tire. After inflation of the tires according to the tire
inflation pressure value , screw protective cap to complete the
installation.
In accordance with the above steps to install other transmitters.
[ ] Transmitter should be installed by professionals. The steps must be in
accordance with Stickers shown on the transmitter to ensure that the
installation is correct and reliable.
：Note ①
②As the transmitters install on the valve mouth, extrusion on the rubber
valve should be avoid to prevent leakage or damage.
③After transmitter installation, you must do the tire dynamic balance test,
otherwise normal driving will be affected.The product only applies to
vacuum tire installation.
4
Installation
Receiver installation steps:
1
2
3
TM
OK
L
Take out receiver, receiver paste board from the box.
Tear up the adhesive protective film on paste board, stick the
receiver on the selected position, adjust the position of the
receiver in order to help the driver read the display information
on the LCD screen.
Connect the power anode with ACC ignition wiring, cathode
with the vehicle power ground. To ensure that the power
connection is correct and the input power is 12 ± 4V DC power.
The installation is completed.
5
Operation
Operation
Pressure Units:kPa
Pressure Units:psi
Pressure Units:bar
Celsius Temperature units:
Fahrenheit Temperature units:
Pressure Alerting
TemperatureAlerting
User Settings
Tire ID read
Tire exchange
Transmitter battery
℃
Tire (Tyre) key
Backlight (Light) key
Menu key
Ok key
Pressure alerting light
Temperature alerting light
System Introduction
After the receiver power wiring is connected, the vehicle ignition
switch turns on, the system start self-checking. LCD screen light up
all the display information ,at the same time buzzer starts buzzing.
Table of contents
