Focal Point POLARIS Assembly Instructions

INSTALLATION & USER INSTRUCTIONS

ODELS COVERED BY THESE INSTRUCTIONS

POLARIS

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e : sales@focalpointfires.co.uk

STONE EFFECT DECORATIVE GAS FIRE

Revision B - 05/13

'2013 Focal Point Fires plc.

GB IE

BS EN 509 : 2000

K 579168

All instructions must be handed to the user

for safekeeping.

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not per-

mitted to copy or adapt any of the content without the

prior written permission of Focal Point Fires plc.

IN THE UK ALWAYS USE A GAS SAFE REGISTERED ENGINEER TO INSTALL, REPAIR OR SERVICE THIS APPLIANCE

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 01202 588601 we’re here to help

lines open between 9am and 5pm, Monday to Friday

• This appliance is an nset Decorative Fuel Effect appliance which provides radiant warmth utilising the latest type

burner technology.

• The fire is designed to suit various types of fireplaces and natural draught flues as detailed in this manual.

• The appliance must be installed by a competent person in accordance with Gas Safety ( nstallation and Use)

Regulations 1998. t is strongly recommended that a GAS SAFE registered engineer be used for this purpose.

• Read all these instructions before commencing installation.

• This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated

space.

• The appliance is designed for installation on to a non-combustible hearth of at least 300mm depth.

• This appliance is factory set for operation on the gas type, and at the pressure stated on the appliance data plate.

• n the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.

• The appliance must be installed in accordance with the following:

• Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.

• The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.

• t should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the

heater. nstalling the heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air

(such as tobacco smoke, candle smoke etc.) exist, may cause the walls to become discoloured.

• WARNING: The manufacturer of this appliance considers all surfaces as working surfaces with the exception of

the control knob and ash pan door.

• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children,

and the elderly or infirm.

• Consult ALL instructions before installation and use of this appliance.

• This appliance is intended for decorative purposes.

• This appliance is free from any asbestos material.

• Refractories and fuel bed are constructed from ceramic fibre.

1.0 I PORTANT NOTES

I N S T A L L A T I O N I N S T R U C T I O N S

'2013 Focal Point Fires plc.

GB IE

•Manufacturers' nstructions.

•The Building Regulations issued by the Department for Communities and Local Government, the Building Standards

(Scotland)

(Consolidation) Regulations issued by the Scottish Development Department.

•Relevant British Standards insofar as the relevant areas are not covered by these instructions.

•For Republic of reland, reference should be made to the current edition of S813 (the relevant standards governing

installation).

Section

1.0

2.0

3.0

4.0

5.0

6.0

6.1

7.0

8.0

9.0

Contents

mportant Notes

Appliance Data

nstallation Requirements

Site Requirements

Ventilation

Unpacking the Appliance

Component Checklist

nstalling the Burner

Fuel Bed Layout

Testing & Commissioning

Page No.

Section

10.0

11.0

12.0

12.1

12.2

12.3

13.0

14.0

Contents

Operating the fire

Spark Gap

Operating Pressure

Flue Spillage Monitoring System

Testing For Spillage

Briefing the Customer

Servicing

Troubleshooting Guide

User nstructions

Page No.

2.0 APPLIANCE DATA

Model Destination

Country Cat

Operating Pressure

(±2.0 mbar) Max Energy nput (kW) Min Energy nput (kW)

Natural gas G20 G25 G30 G31 Gross Net Gross Net

Polaris GB - E 2H 20 - - - 5.5 4.95 3.5 3.15

GB IE

3.0 INSTALLATION REQUIRE ENTS

This appliance MUST NOT be installed into a room containing a bath

or shower, or where steam may be present. The fire has been designed

to fit into a builders’ opening or fireplace conforming to BS 1251 (and

meeting certain dimensional requirements), or a suitable flue box com-

plying with the constructional requirements of BS 715. Either a

‘Replacement Chairbrick’ or a BS 1251 chairbrick should also be fitted

into the builders’ opening. The flue box must be installed onto a suitable

non-combustible insulating surface at least 12mm thick, covering the

entire base are of the box.

The flue must have an effective height of at least three meters, as meas-

ured from the hearth to the top of the flue. Any flue damper plates or

restrictors should be removed and no other restriction fitted to the

flue. Where removal is not practical, the restriction must be fixed in the

fully open position. A natural draught flue system is required, and if pre-

viously used for solid fuel or oil burning, the flue and chimney must be

swept prior to appliance installation. The flue must be checked before

installation by using a smoke pellet or similar to ensure proper draw

and that leakage is not evident at any joints. Repair and re-test as nec-

essary before the appliance is installed. The flue must be connected to

only one fireplace, and the flue must not vent more than one appliance

(i.e. not shared with a gas back boiler). There must be no opening in the

flue apart from the one that the appliance is installed into, and the one

venting the gases into the air. A suitable terminal may be fitted, such as

class GC1, as regulations allow.

This appliance has been tested for use with circular flues of a minimum internal diameter of 175mm. The flue termination (cowl)

must be of a type suitable for use with an inset Decorative Fuel Effect Fire BS5871 part 3 contains further details.

The fireplace opening should be inspected and repairs made where necessary. Any chair brick may be left in place.

The opening W DTH and HE GHT dimensions should be between 455mm and 545mm wide, and 360mm to 470mm high.

Opening DEPTH should be 355mm or greater. Opening DEPTHS include any plaster or infill panels which form part of the instal-

lation.

This appliance requires a natural draught flue system which may be one of the following;

• 225mm x 225mm (9in x 9in) brick or stone.

• 175mm (7in) minimum diameter lined brick or stone.

• 175mm (7in) minimum diameter twin wall flue conforming to BS 715.

Any existing under grate draught device must be sealed off.

The opening wall must be non-combustible.

The appliance requires a hearth with non-combustible surface of at least 12mm thick.

Specifications Polaris - All models

Main burner injector Stereo size 66

Oxypilot S T 9090

Gas Control Copreci 21400/342

Gas nlet 8mm compression - nlet restrictor elbow

gnition Piezo Spark

Spark Gap 3.5 - 4.5mm

Flue specification

225mm x 225mm (9in x 9in) brick or stone.

175mm (7in) minimum diameter lined brick or stone.

175mm (7in) minimum diameter twin wall flue conforming to BS 715.

4.0 SITE REQUIRE ENTS

‘A’

‘B’

‘C’

Figure 1

A. Opening height: 360mm Min / 470mm Max.

B. Opening width: 455mm Min / 545mm Max.

C. Opening depth: 355 mm Min.

3'2013 Focal Point Fires plc.

4.0 SITE REQUIRE ENTS - CONTINUED

The top surface must be at least 50mm above the surrounding floor level, or be surrounded by a raised edge or fender 50mm

high.

Any type of fire surround used with this appliance must be adequately sealed to the wall and floor.

A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening.

Combustible materials, such as wood, may be fitted to within 100mm (4in) of either side of the fireplace opening , providing the

forward projection does not exceed 100mm (4in).

Any combustible side walls must be at least 500mm to the side of the radiant heat source.

As with all heating appliances, any decorations, soft furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper)

positioned too close to the appliance may discolour or scorch.

No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the

same room or space must be taken into consideration when assessing ventilation.

f spillage is detected when commissioning the appliance then amongst other problems there may be insufficient natural ventila-

tion for the correct operation of the flue. This is potentially a greater problem should the property be of modern nature. f the

appliance does not spill with windows open but does with windows closed, this proves that lack of ventilation is the problem, if

not, it will be the flue at fault. nstallation of an air brick in these circumstances may be the best solution. Any ventilation fitted

must comply with BS 5871 part 2 and BS 5440 part 2. Ventilation located underneath or within the immediate vicinity (one metre)

of the fire MUST NOT be used as it may adversely affect the performance of the O.D.S. system.

Spillage detected during commissioning is almost always a result of poor flue performance, which cannot be corrected by any

amount of ventilation. For Republic of reland ventilation may be required, see S 813, CP3, S 327, and any other rules in force.

Read all the instructions before continuing to unpack or install this appliance.

Remove the box containing the firefront, and the bag containing the coals. Remove the cardboard packing pieces, and any bags

containing other fittings or parts. Remove the burner unit from the remaining packaging.

Check that the components supplied correlate with the checklist given in section 6.1. Please dispose of the packaging materials

at your local recycling centre.

GB IE

4'2013 Focal Point Fires plc.

Maximum depth of she f Minimum distance from finished hearth

surface to underside of she f

100mm 745mm

150mm 845mm

203mm 895mm

5.0 VENTILATION

6.0 UNPACKING THE APPLIANCE

Hearth

Builders’

opening

A. Front face of the stone effect body to be flush with fireplace opening.

B. Hearth must extend minimum of 240mm in front of the stone effect body.

C. Hearth must extend minimum of 90mm either side of the stone effect body.

D. Overall hearth width must be at least 540mm.

E. Recommended 70mm minimum for access to control knob.

Notes: Ensure that the gas supp y is iso ated before commencing

insta ation of the app iance.

Check that the thermocoup e connection nut into the rear

of the va ve is secure.

Smoke test the f ue to ensure proper draw and that there

are no eaks present.

Locate the gas supply point. This appliance is suitable for all gas connec-

tions, including those concealed behind the opening.

Using the fitting template provided mark out and drill the position of the

four fixing screws as required using a 7mm masonry bit. These hole posi-

tions are shown on the template together with the position of the inlet

restrictor elbow and the outer profile of the stone effect body.

MPORTANT : The front face of the stone effect body should be flush

(i.e. on the same vertical plane) as

the fireplace opening when the appliance is installed in it’s final position.

nsert the fibre rawlplugs into the fixing holes and then using the fixing

screws provided secure the burner unit to the hearth/base of builders’

opening. Remove any protective film from the lower decorative trim.

Using 8mm diameter pipe, connect the appliance to the gas supply point.

The appliance must be fitted with rigid or semi-rigid pipe of 8mm exter-

nal diameter. The appliance is factory fitted with an inlet restrictor elbow.

Keep the amount of 8mm pipe used in the supply to a minimum - less

than 1.2m where possible. A long run of pipe may cause an unacceptable

drop in the supply pressure.

The stone effect body of the fire is simply placed onto the four sup-

porting lugs and then sits under it’s own weight. Similarly, the upper dec-

orative trim sits on top of the stone effect body. No additional fixing is

required.

Please refer to the relevant section of the user manual.

8.0 FUEL BED LAYOUT

5'2013 Focal Point Fires plc.

Securing the burner

Fitting the stone effect body

Fit the upper decorative trim

7.0 INSTALLING THE BURNER

6.1 UNPACKING THE APPLAINCE GB IE

QUANTITY DESCRIPTION

1 Burner tray assembly

1 Stone effect body

1 Bag of granular burner medium

13 ndividually packaged ceramic pebbles

1 Set of manufacturers instructions

1 Screw and rawlplug pack

1 nlet restrictor tap

1 Fitting template

'2013 Focal Point Fires plc.

Turn on and test the gas supply up to the fire for any leaks, in accordance with current edition of BS6891.

The pilot is visible at the rear of the fuel bed. The control knob is located on the right hand

side of the applaince. The fire features a ‘twin spark’ ignition system to aid lighting, Push the

control knob in fully and turn anti-clockwise through both of the SPARK positions, keeping

fully depressed, hold there for a few seconds. f the fire has not been used for some time,

hold the knob in this position for longer, to allow any air in the pipes to be purged.

Ensure the pilot has lit. f not, return the knob clockwise, and repeat. When the pilot lights

after one of the two sparks, keep the knob depressed in the nine o’clock position for

approximately ten seconds. Now release the knob and the pilot should stay alight. f the pilot

is extinguished during use, wait three minutes before repeating the ignition procedure.

To achieve the H GH setting, push the control knob in slightly and continue turning anti-

clockwise to the high position. The main burner should light after a few seconds. To decrease the setting to LOW, push the knob

in slightly and turn the control knob clockwise to the low setting. To turn to the pilot only position from the H GH or LOW posi-

tions, press the control knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep the knob pressed

in, return to the off position and release.

The gap between the spark electrode and the pilot should be 3.5 - 4.5mm to produce

a good spark.

There should be no need to adjust this. f under any circumstances the electric spark

fails, the pilot may be lit manually by proceeding with the ignition sequence as previously

described, and after turning the control knob through the spark position, the knob

should be held in and the pilot lit with a taper.

Release the pressure test point screw, and attach a pressure gauge. Light the

fire on the H GH setting. To commission the appliance, the operating pressure

must be in accordance with the figures stated in section 2.0 of these instruc-

tions. The fire is factory set to achieve the correct flow rates at the specified

inlet pressure.

Any significant variation in the inlet pressure could indicate a supply problem.

f the inlet pressure is too high, the gas supply meter/governor may be set

incorrectly. This should be checked with the fire running and if necessary reset

by the gas supplier. f the inlet pressure is too low, then check the meter/gov-

ernor pressure with the appliance running. f this is less than the inlet pressure

stated in section 2.0 of these instructions it will need to be reset by the gas

supplier. f the inlet pressure is too low, but the meter/governor pressure is acceptable, then a problem in the supply pipework

is to be suspected. Upon satisfactory checking of the inlet pressure, turn the fire off, disconnect the pressure gauge and refit the

test point screw. Light the fire and check for gas soundness. n the event that the inlet pressure is not in accordance with the fig-

ures stated in the data section of these instructions, the appliance must not be commissioned, and the problem investigated and

rectified.

This fire is fitted with a flue spillage safety device (ODS). f the fire shuts down during use for no apparent reason then several

things may be suspected. f a door or window has been opened creating a draught, then pilot disturbance is the problem, and

removal of the draught should resolve this. f a grommet seal has been left out of the firebox (if fitted) then this also will also

cause intermittent shutdown. The gas pressure reaching the fire must also be checked. The thermocouple connection into the

back of the gas control valve may also have worked loose during installation, simply tighten to remedy if this is the case.

12.1 FLUE SPILLAGE ONITORING SYSTE

Figure 4

12.0 OPERATING PRESSURE

11.0 SPARK GAP

10.0 OPERATING THE FIRE

9.0 TESTING AND CO ISSIONING GB IE

FIN:

Figure 3

Spark gap

f pilot disturbance is not the cause, then the ODS safety system may be in operation. Switch the appliance OFF, check the flue

and carry out any remedial work required. Re-light the fire and carry out a spillage test. DO NOT allow the appliance to be used

if it continues to fail a spillage test.

The aeration hole of the pilot must be carefully cleaned out on each annual service to ensure continued function of the ODS.

The spillage monitoring system shall not be adjusted, modified, or put out of operation by the installer. Any spare parts fitted

MUST be of a type supplied for the purpose by the appliance manufacturer.

f the fire is not spilling, then further guidance should be sought, using the Troubleshooting section as a guide.

Close all doors and windows to the room containing the appliance. Let the fire run on H GH for five minutes. Take a smoke match,

light it, and using a smoke match tube, hold it at the top edge of the fire opening, 25mm down and 25mm in. Starting 50mm in

from either side, run the smoke match across the opening. All the smoke should be drawn away up the flue. Any smoke return-

ing into the room indicates that spillage is occurring. f the initial spillage test fails, run the fire for a further 10 minutes and repeat

the test. When the test has been completed satisfactorily, repeat with any extractor fans in the premises running on the highest

setting, and any communicating doors open. Finally, repeat with all doors open.

NOTE: If spi age is sti indicated after undertaking a of the above, there may be a fau t in the f ue, or insufficient ven-

ti ation is present. f the problem cannot be rectified immediately, then expert advice should be sought. nform the user, discon-

nect the fire, and attach an explanatory label.

All instructions must be handed to the user for safekeeping. Show the customer how to ight and contro the fire.

After commissioning the appliance, the customer should be instructed on the safe use of the appliance and the need for regular

servicing. Frequency of service depends on usage, but MUST be carried out at least once annually.

Scratched and other superficial damage to the matt black paintwork of the appliance can be covered with matching heatproof

spray. Use only the manufacturers’ recommended spray paint. Paint only when the fire is OFF and cold. Always mask off the sur-

rounding area to prevent contamination with overspray. Ventilate the room during the use of the spray.

Ensure that the fire is fully cold before attempting service. A suggested procedure for servicing is detailed below.

1. Lay out the dust sheet and tools.

2. nspect the area around the top of the fireplace opening for signs of spillage.

3. Carefully remove the ceramic components and the upper decorative trim.

4. Carefully lift off the stone effect body.

5. solate the gas supply at the appliance inlet elbow, and disconnect the gas supply pipe.

6. Remove the four screws securing the burner to the hearth.

7. Remove the burner unit from the fireplace opening and empty the granular burner medium.

6. Check the base of the fireplace opening for rubble accumulation and remove. f debris is excessive,

initiate remedial work on the flue.

7. Check the flue with smoke pellet for correct operation.

8. Strip off the burner pipes and clean thoroughly.

9. Clean out the injector and pilot assembly. DO NOT attempt to dismantle the pilot unit.

10. Ensure the injector is aligned squarely in the injector bracket. Re-assemble and re-fit the burner tray.

'2013 Focal Point Fires plc.

13.0 SERVICING

12.3 BRIEFING THE CUSTO ER

12.1 FLUE SPILLAGE ONITORING SYSTE - CON GB IE

12.2 TESTING FOR SPILLAGE

Match

Crimp

Tube

Figure 5 : Cross section of smoke match tube

Make a smoke match tube from 10mm diameter

tube. Seal off one end and crimp the tube to pre-

vent the smoke match from sliding down inside.

Spillage test - Figure 6

A.25mm down from top of

opening

B. 25mm in from front of

opening.

C. Disregard outer 50mm

either side of fireplace

opening

Fireplace Opening

Smoke Match

n Tube

Figure 6

11. Re fit and replace the ceramics, using genuine spares where necessary.

12. Turn on the gas supply, and leak test.

13. Check any purpose provided ventilation is un-obstructed.

14. Light the fire and test for spillage.

15. Check setting pressure and safe operation of the appliance.

For specific servicing instructions, see the relevant sections.

CLEANING THE CERA ICS

Remove the ceramic components. Gently clean in the open air. Be careful not to create dust from the pebbles. Where neces-

sary replace damaged components with genuine spares. Seal scrap components in plastic bags and dispose of at proper refuse

sites as directed.

Re-fit the pebbles carefully by referring to the relevant section of these instructions.

CLEANING THE STONE EFFECT BODY

The stone effect body may be cleaned using a soft dry brush or by using a mild water-based detergent and a cloth. f these meth-

ods of cleaning are unsuccessful, and as a last resort, stubborn marks may be removed by gently rubbing with a fine abrasive paper

i.e. wet and dry paper. t is not recommended to use water unless the entire body can be removed from the fire and rinsed under

a tap. Do not refit the body to the fire until completely dry. Whichever method of cleaning is to be employed, it is recommend-

ed that a small hidden area be tested before proceeding to clean the entire body. Do not use polish, wax or solvent based

cleaners or detergent as these may stain or discolour the body.

Remove the tray as previously described. The pilot unit can be removed by undoing the tubing nut, the thermocouple nut on

the rear of the valve, lint arrestor, two securing screws, and lifting away. Remove the tubing nut from the valve end of the pilot

pipe, and blow through to dislodge any debris that may be present. Clean the exterior of the pilot assembly with a soft brush

and blow through the flame ports on the pilot head. Check the aeration holes are free from lint or dirt. The pilot assembly is a

non-serviceable item, and should not be taken apart. The aeration hole must be absolutely clear internally for proper operation.

A thoroughly cleaned (inside and out) oxypilot will cure a wide range of ignition faults. Remove the two tubing nuts on the

ends of the gas pipe to the injector elbow. Release the screw through the supporting leg and lift assembly clear. The injector

pipe can now be checked for debris. Remove the nut retaining the injector elbow. Blow through the elbow to remove any

debris.

Fire sparks but pi ot does not ight No gas to fire, check isolators are open.

Pipework blockage, clean out.

Air not fully purged, re-purge supply or wait longer.

Spark earthing to metal work, reset gap correctly.

Blocked pilot, clean out internally.

Pi ot ights but then goes out Severe restriction in gas supply, clear obstruction.

Faulty thermocouple, replace pilot unit.

Hold control knob in for longer.

Fire does not spark at pi ot HT lead detached, refit.

Spark gap too large or small, reset correctly.

Faulty piezo unit, replace.

Debris shorting out electrode, clean.

Fire runs for a time and then cuts off Excessive room draught or flue pull, rectify.

Loose or faulty thermocouple, rectify.

ODS system in operation.

Lint in pilot aeration hole, clean thoroughly internally

Pi ot f ame shrinks when fire is on high Poor gas flow to fire, check pressure with fire on high.

f pressure is low, remove any restriction in pipework or valve.

Check all isolators are adequately sized and fully open.

Check meter pressure is adequate.

Lint in pilot aeration hole, clean thoroughly internally.

Fire sme s when first it or in use Newness smell from brand new appliance.

Spillage occurring. Carry out spillage test and rectify any problems.

Low temperature sealants or combustible materials used in incorrect positions.

14.0 TROUBLESHOOTING GUIDE

13.0 SERVICING - CONTINUED GB IE

13.1 CLEANING

13.2 DIS ANTLING THE BURNER UNIT

'2013 Focal Point Fires plc.

• The installation and Servicing of this fire MUST only be carried out by a competent person in accordance with local Codes

and/or Regulations, Building Regulations and the manufacturer's instructions. Failure to comply with these could lead to pros-

ecution and invalidate the appliance warranty. n the event of gas leakage from the appliance, the gas supply must be turned off

at the nearest isolating valve. This appliance is only suitable for the gas type for which it is supplied.

• Keep a note of the installer's name and address, GAS SAFE registration number and the original purchase receipt and the date

of installation. Failure to produce this information may invalidate the warranty. The appliance should be serviced regularly to

ensure continued safe operation. See the servicing section for further reference.

• Parts of this appliance become naturally hot during use. t is recommended that a suitable fireguard is used, especially where

young children, pets, the elderly or infirm are concerned. The manufacturer of this appliance considers all surfaces as working

surfaces with the exception of the control knob and ash pan door.

• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the

elderly or infirm.

• The appliance should be serviced regularly to ensure continued safe operation. Frequency of service will depend on use, but

MUST be carried out at least once annually.

• Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed paper), low tem-

perature surrounds etc may discolour if fitted too close to the fire. See relevant section for further details on clearances to

combustibles. No combustible materials or flooring should protrude onto the hearth.

• This appliance incorporates a combustion monitoring system (ODS).

• DO NOT burn any foreign material on this fire, the coals must be of the correct type and laid out in accordance with the rel-

evant section of these instructions. Failure to do so could create a hazard or lead to sooting.

• The fire is only suitable for use with the gas type for which it is supplied.

• This appliance is fitted with a flue blockage safety device which will shut down the fire if abnormal flue conditions occur. t is

NOT a substitute for an independently mounted Carbon Monoxide detector.

• This fire is supplied with a particular style of firefront. Use of the firefront will ensure an adequate airflow under the firebed

for the correct functioning of this appliance. Use ONLY the firefront supplied with the appliance. Use of any other firefront

could be dangerous.

• Should any home improvements be carried out to the property after the fire is installed, such as installation of extractor fans

for example, the fire should be re-checked by a competent person for safe operation.

U S E R I N S T R U C T I O N S

2.0 CLEARANCES TO CO BUSTIBLES

Section Content Page No

1.0 mportant Notes 1

2.0 Clearances to Combustibles 1

3.0 Fire guards 2

4.0 Ventilation 2

5.0 Operating nstructions 2

6.0 Flue Spillage Monitoring System 3

7.0 Fuel Bed Layout 3

8.0 Cleaning 5

9.0 List of Replacement Parts 5

10.0 nstallation Details 5

11.0 Service History 6

A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening.

Combustible materials, such as wood, may be fitted to within 100mm of either side of the fireplace opening, providing the for-

ward projection does not exceed 100mm.

Any combustible side walls must be at least 500mm to the side of the radiant heat source.

As with all heating appliances, any decorations, soft furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper)

positioned too close to the appliance may discolour or scorch.

1.0 I PORTANT NOTES

1'2013 Focal Point Fires plc.

GB IE

Maximum depth of she f Minimum distance from finished hearth

surface to underside of she f

100mm 745mm

150mm 845mm

203mm 895mm

The fireguards specified in BS 8423 are intended to protect people from falling into a fire, prevent burns and reduce the risk of

injury, particularly to young children and the infirm. n addition it is intended to reduce the risk of fire resulting from clothing

and/or other flammable materials coming into contact with, or in proximity to, burning fuel and/or hot surfaces.

Fireguards can be permanently fixed in position or can be moveable, and can incorporate open fires including combination grates,

or closed fires, including room heaters and stoves. See figures 1 & 2 for fireguard examples.

The fireguards specified are not intended to reduce the risk of fires caused by flying particles, which are covered by BS 3248.

No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the

same space or room, and the results of a spillage test must be taken into consideration when assessing ventilation requirements,

this will have been carried out by your registered installer.

For Republic of reland, ventilation may be required, see S 813, CP3, S 327, and any other rules in force.

WARNING : Ventilation openings (where fitted) must never be blocked or restricted in any way.

The pilot is visible at the rear of the fuel bed. The control knob is located on the right hand

side of the applaince. The fire features a ‘twin spark’ ignition system to aid lighting, Push the con-

trol knob in fully and turn anti-clockwise through both of the SPARK positions, keeping fully

depressed, hold there for a few seconds. f the fire has not been used for some time, hold the

knob in this position for longer, to allow any air in the pipes to be purged.

Ensure the pilot has lit. f not, return the knob clockwise, and repeat. When the pilot lights after

one of the two sparks, keep the knob depressed in the nine o’clock position for approximately

ten seconds. Now release the knob and the pilot should stay alight. f the pilot is extinguished

during use, wait three minutes before repeating the ignition procedure.

To achieve the H GH setting, push the control knob in slightly and continue turning anti-clock-

wise to the high position. The main burner should light after a few seconds. To decrease the setting to LOW, push the knob in slightly

and turn the control knob clockwise to the low setting. To turn to the pilot only position from the H GH or LOW positions, press the

control knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep the knob pressed in, return to the off

position and release.

3.0 FIRE GUARDS GB IE

Figure 1

Example of moveable fireguard for portable heating appliances

Key

1. Optional base section for total enclosure of a wall mounted appliance

2. Points for attachment to a wall.

Figure 2

Example of detachable fireguard

Key

1. Detachable fireguard

2. Screw eye

4.0 VENTILATION

5.0 OPERATING THE APPLIANCE

FIN:

Figure 3

2'2013 Focal Point Fires plc.

Other manuals for POLARIS

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point REFLECTION User guide

Focal Point

Focal Point EBONY ELECTRIC Assembly Instructions

Focal Point

Focal Point BLENHEIM Assembly Instructions

Focal Point

Focal Point L27G Guide

Focal Point

Focal Point BLENHEIM STYLE Guide

Focal Point

Focal Point DS-EHS01-41E Assembly Instructions

Focal Point

Focal Point ATHERSTONE SLATE ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point Excelsior Fanflue User guide

Focal Point

Focal Point Fuego User guide

Focal Point

Focal Point HANNINGTON BRASS F500310 Assembly Instructions

Focal Point

Focal Point eko 3040 Guide

Focal Point

Focal Point EKOFIRES EKO 5090 Assembly Instructions

Focal Point

Focal Point KAVACHI Assembly Instructions

Focal Point

Focal Point Charmouth Assembly Instructions

Focal Point

Focal Point BLENHEIM STYLE Guide

Focal Point

Focal Point HORIZON Assembly Instructions

Focal Point

Focal Point SAN FRANCISCO CHARLESTON Assembly Instructions

Focal Point

Focal Point NOIR L23 Assembly Instructions

Focal Point

Focal Point TUSCANY Guide

Focal Point

Focal Point HANNINGTON Assembly Instructions

Focal Point

Focal Point Wickes User manual

Focal Point

Focal Point EVOKE F500176 Assembly Instructions

Focal Point

Focal Point FPFBQ257 BLENHEIM Assembly Instructions

Focal Point

Focal Point Exselsior Slimline User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual