Focal Point EBONY ELECTRIC Assembly Instructions

INSTALLATION & USER INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

MODELS COVERED BY THESE INSTRUCTIONS

Ebony LED Electric Fire

WALL MOUNTED ELECTRIC FIRE

Revision F - 03/19

GB IE

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

Email: [email protected].uk

MODEL SHOWN: EBONY LED ELECTRIC FIRE

This product is only suitable for well insulated spaces or

occasional use.

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not

permitted to copy or adapt any of the content without

the prior written permission of Focal Point Fires plc.

I N S TA L L AT I O N & U S E R I N S T R U C T I O N S

GB IE

Section Contents Page No.

1.0 Important Notes 2

2.0 Installation Requirements 3

3.0 Appliance Data 3

4.0 Component Checklist 4

5.0 Site Requirements 4

6.0 Clearances To Combustibles 5

7.0 Unpacking The Appliance 5

8.0 Installation Wall Mounted 5

Section Contents Page No.

9.0 Operating the Appliance 8

10.0 Safety Cutout System 11

11.0 Cleaning and Maintenance 11

12.0 Troubleshooting Guide 12

13.0 Servicing 12

14.0 Appliance Dimensions 13

15.0 Guarantee - Terms and Conditions 13

1.0 IMPORTANT NOTES

IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY

AND RETAINED FOR FUTURE REFERENCE.

When using this electrical appliance, basic precautions should be followed to reduce the risk

of fire, electric shock and injury to person, including the following:

• This heater must be used on an AC supply only and the voltage marked on the heater’s

rating label must correspond to the supply voltage.

• DO NOT switch the appliance on until it is properly installed as described in this

manual.

• This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/off the appliance

provided that it has been placed or installed in its intended normal operating position and

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved. Children aged from 3 years and less than 8 years

shall not plug in, regulate and clean the appliance or perform user maintenance.

• CAUTION: Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are present.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

• The heater must not be located immediately below a socket-outlet.

• DO NOT use this heater in the immediate surroundings of a bath, a shower or a

swimming pool.

• WARNING: In order to avoid overheating, do not cover the heater.

• DO NOT use this heater with a programmer, timer, separate remote-control system or

any other device that switches the heater on automatically, since a fire risk exists if the

heater is covered or positioned incorrectly.

• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal

cutout, this appliance must not be supplied through an external switching device, such as a

timer, or connected to a circuit that is regularly switched on and off by the utility.

• WARNING: This heater is not equipped with a device to control the room

temperature.Do not use this heater in small rooms when they are occupied by persons not

capable of leaving the room on their own, unless constant supervision is provided.

• eep furniture, curtains and other fabric material away from the appliance.

• DO NOT leave the appliance unattended during use.

3.0 APPLIANCE DATA

Weight (kg): 15kg

Dimensions: H 620 x W 520 x D 148 (mm)

Supply Voltage: 220~240V AC, 50Hz

Fuse Rating: 13 Amp

Heating Elements: 1500W

Lighting: LED

This fire is fitted with LED’s (Light Emitting Diode) in place of conventional bulbs. LED’s generate the same light levels as

conventional bulbs, but use a fraction of the energy consumed. LED’s are maintenance free and will not require replacing during

the life of the product.

The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated) and 1.8 metres of electrical cable. It is therefore

necessary for a suitable electrical socket to be located within this distance and be easily accessible. This appliance is designed to

be wall hung, using the wall fixtures/fixings provided. DO NOT recess any part of appliance into the wall. This appliance is

suitable for installation in static holiday/park homes.

2.0 INSTALLATION REQUIREMENTS

• From time to time, check the cord for damage. Never use the appliance if the cord

or any part of the appliance shows signs of damage.

• DO NOT run the mains cable under carpets, rugs etc.

• DO NOT cover or obstruct the heater in any way. Overheating will result if it is

accidentally covered.

• Never immerse the product in water or any other liquids.

• DO NOT use the appliance outdoors.

• Before cleaning the appliance, ensure it is unplugged from the power and that it is

completely cool.

• DO NOT clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer. It

could cause danger to the user or damage to the appliance.

• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may

result in electric shock, fire or damage to the appliance.

• DO NOT install the fire using an extension cord.

• Unplug from the mains supply if the appliance is not to be used for long periods.

• This product is only suitable for well insulated spaces or occasional use.

1.0 IMPORTANT NOTES - CONTINUES GB IE

Model EBONY LED ELECTRIC

Item Symbol Value Unit Item Unit

Heat output Types of heat input, for electric storage local

space heaters only

Nominal

heat output

Pnom 1.5 W Manual heat charge control with

integrated thermostat

N/A

Minimum heat

output

(indicative)

Pmin 0.75 W Manual heat charge control with

room and/or outdoor temperature

feedback

N/A

Maximum

continuous heat

output

Pmax, c 1.5 W Electronic heat charge control with

room and/or outdoor temperature

feedback

N/A

3.0 APPLIANCE DATA - CONTINUED GB IE

4.0 COMPONENT CHEC LIST

Quantity Description

1 Heater unit

1 Decorative glass fascia

1 Remote control handset

2 Metal fixing plates

5 Wall plugs

5 Fixing screws

6 Metal plate screws

5.0 SITE REQUIREMENTS

It should be noted that the appliance creates warm convected air currents. These currents move heat from the room

surroundings to, and up the wall surfaces adjacent to the heater.

Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco

smoke) exist, may slightly discolour wall finishing.

If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and ability of the wall to

carry the weight of the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or

structural members of the house frame are not damaged.

If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use, you should take

professional advice and obtain the correct fixings. Alternatively, find a more suitable wall location.

DO NOT

• mount on a ceiling or floor

• recess any part of the appliance into the wall, or run the supply cable under carpets

• site any electrical equipment e.g. plasma screen TV sets etc, on the wall below the appliance.

• site in a position where curtains or drapes could cover the appliance, or other soft materials could cover e.g. below a coat

rack

• site behind an opening door where mechanical impact/damage could occur

Auxiliary electricity consumption Fan assisted heat output N/A

At nominal

heat output

elmax 0.0 W Type of heat output/room temperature control

At minimum

heat output

elmin 0.0 W Single stage heat output and no

room temperature control

In standby mode elSB 0.0 W Two or more manual stages no

temperature control

With mechanical thermostat room

temperature control

With electronic room temperature

control

Yes

Electronic room temperature

control plus day timer

Yes

Electronic room temperature

control plus week timer

Yes

Other control options

Room temperature control with

presence detection

Room temperature control with

open window detection

Yes

With distance control option Yes

With adaptive start control Yes

With working time limitation Yes

With black bulb sensor No

Contact details Focal Point Fires, Avon Trading Park, Christchurch Dorset, BH23 2BT

5.0 SITE REQUIREMENTS - CONTINUED

7.0 UNPAC ING THE APPLIANCE

Caution: This appliance is heavy. Always seek assistance whilst unpacking and/or during installation. Please read

all the instructions before continuing to unpack or install appliance.

Before starting the installation of this fireplace, please read the following:

1. The installation should be carried out by two adults to avoid injury or damage. If for any reason it is considered too heavy,

please obtain assistance.

2. When lifting the fireplace, always keep your back straight. Bend your legs and not your back. Avoid twisting at the waist. It is

better to reposition your feet.

3. Avoid upper body / top heavy bending. Always bend from the knees rather than the waist. Do not lean forward or sideways

while handling the heater.

4. Always grip the heater with the palm of the hand. Do not use the tips of fingers for support.

5. Always keep the heater as close to the body as possible. This will minimize the cantilever action.

6. Use gloves to provide additional grip.

7. Unpack the package and lift the product gently out of the box, put it on a flat surface with the front panel facing up.

IMPORTANT - PLEASE READ COMPLETELY THROUGH THE INSTRUCTIONS AND VERIFY THAT ALL LISTED

ARTS ARE PRESENT BEFORE ASSEMBLY

GB IE

8.0 INSTALLATION WALL MOUNTED

CAUTION: DO NOT CONNECT THE APPLIANCE TO THE

ELECTRICAL SUPPLY AT THIS TIME.

Focal Point Fires plc. assumes absolutely no responsibility for injuries and damages

that may occur due to improper installation or handling.

Remove any protective film coatings from the finished/decorative surfaces of the

appliance, if any. After having selected the final mounting position of the appliance

taking into account the integrity of the wall the firebox of the appliance may be

secured to the wall.

To ensure customer safety, be sure to design the installation so that the strength of

both the wall and any wall fixings used are sufficient. The appliance should not be

installed until all wet plastering and/or dry wall sanding and wall painting has been

completed. Do not block the ventilation holes of the appliance. The wall onto

which the appliance is installed must be flat. Install only on a vertical surface. Avoid

sloped surfaces. Installation onto anything other than a vertical wall may result in fire,

damage or injury.

If the appliance is to be mounted on the inner leaf of a conventional cavity brick wall,

or a solid wall, then the wall plugs and fixing screws provided may be used.

Depending on the condition of the wall it may be necessary to use additional fixings. In this situation, any additional fixings and

wallplugs should be of the same size and type as the ones provided.

If the appliance is to be mounted on a dry lined wall or a timber framed construction wall then efforts should be made to fix in

at least two positions vertically, into one of the wooden studs, or supporting wooden members of the wall using the fixing

screws provided. If this is not achievable then the wall should be strengthened using appropriate building materials.

The wall where the appliance is to be

installed must be capable of

long-term support of the total load of

the appliance. Measures should also

be taken to ensure sufficient strength

to withstand the force of

earthquakes, vibration and other

external forces. Plasterboard alone is

not considered to be a structural

material. It is not recommended to

rely on plasterboard fixings alone to

support the weight of the appliance.

WARNING



• site where the supply cable would become a trip hazard

• sit, stand or forcefully pull on the appliance

• obstruct, cover or force items into the openings

• use the heater to dry clothes

• site/use in an outdoor location(s)

6.0 CLEARANCES TO COMBUSTIBLES

It is important that the following clearances are maintained from the appliance to combustible materials. These clearances are

dependent on the mounting location as defined below:

• The minimum distance from the top of the appliance to a ceiling is 300mm

• The minimum distance from the bottom of the appliance to the floor is 300mm

• The minimum distance to the sides of the appliance is 200mm

• The minimum distance to the front of the appliance is 500mm

8.0 INSTALLATION WALL MOUNTED - CONTINUED GB IE

Installing the fixing screws into the wall.

1. Insert three of the fixing screws into the top three wall plugs.

Installing the metal fixing plates to the back of the fire.

1. Carefully place the fire on it’s front.

2. Align the metal fixing plates (A) with the screw holes located

at the back of the fire box.

3. Use two of the metal plate screws to fix each of the metal

fixing plates to the firebox.

4. Ensure the metal fixing plates are securely attached.

Installing the wall plugs into the wall.

1. Drill 5 holes (8mm diameter, 40mm deep) into wall.

2. Insert the supplied wall plugs into the drilled holes.

3. Please refer to the diagram for hole locations.

Please note: Before drilling into walls, always check that

there are no hidden wires, pipes, etc.Make sure that

screws and wall plugs supplied are suitable for

supporting the unit in your surface. Consult a qualified

person if you are not sure.

8.0 INSTALLATION WALL MOUNTED - CONTINUED GB IE

Securing the fire to the wall.

1. Insert one the fixing screws into the hole in each of the metal

fixing plates.

2. Fully tighten the screws to secure the fire to the wall.

3. Ensure the fire is secured to the wall.

Installing the front fascia.

1. Hold the glass fascia securely and hang it onto the firebox

hooks, which are located on both sides of the firebox.

2. The glass fascia should be secured on all four firebox hooks.

3. Check to make sure the glass fascia is securely in place.

Hanging the firebox onto the wall.

1. Check to make sure the fixing screws are securely

attached to the wall.

2. Lift the firebox and hang on the fixing screws.

8.0 INSTALLATION WALL MOUNTED - CONTINUED

9.0 OPERATING THE APPLIANCE

GB IE

The control panel is on the right side of the unit.

When a function is changed from the control panel or remote there will be a corresponding indicator displayed. The indicator shows the

function changed and the level selected. When the function is turned off, the corresponding indicator will fade off.

Securing the front fascia.

1. Locate the hole on both left and right sides and insert a

screw through the hook, into the fireplace insert.

2. Tighten screw to pass it through the hook, on both sides.

3. Ensure the front fascia is secure.

Note: Tighten up the screw carefully, to avoid damage to the

front panel.

1. ON/OFF

2. HEATER

3. TIMER

4. BRIGHTNESS

5. CHILD SAFETY LOC

6. PLUS

7. MINUS

Power Button

This button will not only put the fireplace insert in a standby mode, but also you

can see the flame effect through the screen. This will turn off all functions at once.

Heater

The fireplace contains a fan forced heater.

The default setting temperature is 72°F (22°C).

The thermostat setting range is 50°-86°F or 10°-30°C.

The thermostat is adjustable by 2°F or 1°C increments.

To change between °F and °C press and hold the Heater button for 5 seconds.

Timer

Pressing the timer button repeatedly will cycle through the following timer

settings: 30 minutes, 1 hour, 2 hr, 3 hr, 4 hr, 5 hr, 6 hr, 7 hr, 8 hr and off.

The fireplace will automatically turn off when the timer reaches zero minutes.

TIMER SETTING OPERATION

Timer Setting:

Note: You can not set the weekly timer by the control panel, but you can set the day timer. The day setting time is 30 (min) -

1H-2H-3H ---- 8H; The previous screen display shows the settled number(1/2/3…8) and later shows H(Hour); By remote

control, you can set both the day and weekly timer, the specifications are as below:

1. Standby mode: calibrate present time

To calibrate the present time the appliance must be turned off, but the power must be on at the socket.

1) Press and hold the button for 5 seconds, the digital tube will flash, then press and button to set the day of the

week (1 is Monday, 2 is Tuesday, 3 is Wednesday, 4 is Thursday, 5 is Friday, 6 is Saturday and 7 is Sunday).

2) Press a second time, the first digit of the digital tube will start to flash, then press and button to set the hour (10

for example).

3) Press a third time, the first digit of the digital tube will stay on and the last digit of the digital tube will flash, then set

minutes (47 for example).

4) Press again to set the current time calibration setting and turn on the power. The digital display will then show the

ambient temperature.

9.0 OPERATING THE APPLIANCE - CONTINUED GB IE

Brightness

This button controls the brightness of the flame effect.

Child safety lock

The child safety lock is adjustable from remote control only.

Holding the child safety lock button for 5 seconds disables or enables all

functions on the control panel and remote control.

Plus

Function increase of any function button.

Minus

Function decrease of any function button.

Days

OFF

Celsius

Fahrenheit

Heater

Timer Brightness

Child safety lock

Temperature/ time

9.0 OPERATING THE APPLIANCE - CONTINUED

2. Set the week timer:

1) Press on the remote control. Press or button to set the day time. Press to set the time to 30 (min)

-1H-2H-3H ---- 8H-00; press the to set the time to 8H-7H-6H---- 30 minutes.

While making any settings relevant to timer setting, the screen will also display the timing icon . When the timer setting has

only 99 seconds left, the digital tube will show the seconds left.

2) Press for 5 seconds to set the weekly timer.

Press for 5 seconds, and the display panel will show ON and MON , while the digital display showing'…',

Weekly timer set, start from Monday, for example setting Monday: (Monday on status-Monday off status-Thursday on

status-…..Sunday off status.)

1) Press the first time, through the ' ' button to set the start working time on Monday, while the display board

shows ON and MON will flash at the same time. First, set the hour, the first two digital of the tube showing hours, you can

press button to set the hour.

2) Press the second time to set minutes. Ten minutes is consider to be a unit and you could press button to adjust

minutes (from 10,20-50-00 minutes).

3) Press for the third time, to set the power off-working time on Monday. The ON icon will be disappear and at the same

time the OFF icon will flash on (the MON icon will not disappear). First, set hours by pressing plus and minus button. The first

two digit will display hours.

4) Press a fourth time to set the minutes, you can adjust the minutes by pressing plus and minus button.

You will finish setting the Monday timer setting after four time setting operation. Press again to change the setting on-off

situation on Tuesday. The operation method is same as Monday. When you finish to set the whole week, the digital tube will

show the ambient temperature. This indicate the setting have been finished.

3. If you do not want to set the on-off timer on a certain day of the week, you need to press the timer key

continuously for four times to skip this day.

For example, you do not need to set on-off status on Tuesday. When the Monday timer setting is finished, press the timer

setting key, then you could set Tuesday. ON and MON will disappear. Instead, ON and TUE will lit up. At the same time the

first two digital of the tube display: : .’ . You should not press plus and minus button to set time. You should press the timer again

, and the digital tube will display‘: . : . : . :’( minutes). At this time, do not press the plus and minus button, press the timer third

time, the ON icon on the display board will disappear while OFF icon lit up. TUE icon will appear and the first two digit of

the tube display ‘: : .’(hour setting). Do not press plus and minus button at this time. Press the timer the fourth time, the digit

tube will display ‘: . : . : . :’(minutes). Press again the timer button. By this way, it will not set on that day and the display board

and the digit tube will transfer to Wednesday set.

4. The same day timing and weekly timing conflict, according to the principle of first switch to the first set, all

settings need memory function

5.Child lock：The child safety lock is adjustable from remote control only.

Holding the child safety lock button for 5 seconds disables or enables all functions on the control panel and remote control.

6.Temperature control energy-saving features: (additional hidden features)

1 When the difference between acutal detected temperature and set temperature are within 3°C (for example, set 18°C and

detected 16°C -18°C), heating power 750w.

2 When the difference between acutal detected temperature and set temperature exceeds 3°C (for example, set 18°C,

detected as 15°C or below), heating power 1500w.

3 when the actual detected temperature is 1°C higher than the set temperature, the heating will be off (for example, set to

27°C, the actual test is 28°C), the fan will stop working after 10 seconds.

4 Press the power off button on the control panel, the temperature control function will record the last setting when power

on again.

GB IE

Other manuals for EBONY ELECTRIC

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point L30 PIANO NG Assembly Instructions

Focal Point

Focal Point F500115 User manual

Focal Point

Focal Point F500283 Assembly Instructions

Focal Point

Focal Point blenhein multiflue Assembly Instructions

Focal Point

Focal Point Fuego User guide

Focal Point

Focal Point PANORAMIC COMPLETE ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point Envy Guide

Focal Point

Focal Point Excelsior Expanse Guide

Focal Point

Focal Point COMO L23 User manual

Focal Point

Focal Point SAN FRANCISCO CHARLESTON Assembly Instructions

Focal Point

Focal Point Purist Guide

Focal Point

Focal Point NERO CUBE LCD Assembly Instructions

Focal Point

Focal Point COLUMBUS EF12-36 Assembly Instructions

Focal Point

Focal Point PI27 BLENHEIM Assembly Instructions

Focal Point

Focal Point MALMESBURY LED ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point PINOIR Guide

Focal Point

Focal Point KAVACHI Assembly Instructions

Focal Point

Focal Point oregon User guide

Focal Point

Focal Point F820590 FPFBQ392 User manual

Focal Point

Focal Point EF11-36 PASADENA Assembly Instructions

Focal Point

Focal Point DS-EHS01-41E Assembly Instructions

Focal Point

Focal Point AVANT User guide

Focal Point

Focal Point HANNINGTON BRASS F500310 Assembly Instructions

Focal Point

Focal Point BLENHEIM HE Assembly Instructions

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual