Focal Point HANNINGTON Assembly Instructions

I STALLATIO & USER I STRUCTIO S

MODELS COVERED BY THESE I STRUCTIO S

HA I GTO

TAPER GAS I SET TRAY

I SET DECORATIVE GAS FIRE

Revision E - 12/13

'2013 Focal Point Fires plc.

GB IE

All instructions must be handed to the user

for safekeeping.

Please note : Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not per-

mitted to copy or adapt any of the content without the

prior written permission of Focal Point Fires plc.

I THE UK ALWAYS USE A GAS SAFE REGISTERED E GI EER TO I STALL, REPAIR OR SERVICE THIS APPLIA CE

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e : sales@focalpointfires.co.uk

MODEL SHOW : HA I GTO BRASS

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 01202 588601 we’re here to help

lines open between 9am and 5pm, Monday to Friday

• This appliance is an nset Decorative Fuel Effect appliance which provides radiant warmth utilising the latest type burner technology.

• The fire is designed to suit various types of fireplaces and natural draught flues as detailed in this manual.

• The appliance must be installed by a competent person in accordance with Gas Safety ( nstallation and Use) Regulations 1998. t is

strongly recommended that a GAS SAFE registered engineer be used for this purpose.

• Read all these instructions before commencing installation.

• This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space.

• The appliance is designed for installation on to a non-combustible hearth of at least 300mm depth.

• This appliance is factory set for operation on the gas type, and at the pressure stated on the appliance data plate.

• n the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.

• The appliance must be installed in accordance with the following:

• Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.

• The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.

• t should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the heater. nstalling the

heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air (such as tobacco smoke, candle smoke

etc.) exist, may cause the walls to become discoloured.

• WAR I G: The manufacturer of this appliance considers all surfaces as working surfaces with the exception of the control knob

and ash pan door.

• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the elder-

ly or infirm.

• Consult ALL instructions before installation and use of this appliance.

• This appliance is intended for decorative purposes.

• This appliance is free from any asbestos material.

• Refractories and fuel bed are constructed from ceramic fibre.

1.0 IMPORTA T OTES

I S T A L L A T I O I S T R U C T I O S

'2011 Focal Point Fires plc.

GB IE

'2013 Focal Point Fires plc.

•Manufacturers' nstructions.

•The Building Regulations issued by the Department for Communities and Local Government, the Building Standards

(Scotland)

(Consolidation) Regulations issued by the Scottish Development Department.

•Relevant British Standards insofar as the relevant areas are not covered by these instructions.

•For Republic of reland, reference should be made to the current edition of S813 (the relevant standards governing

installation).

Section

1.0

2.0

3.0

4.0

5.0

6.0

6.1

7.0

8.0

9.0

10.0

11.0

11.1

Contents

mportant Notes

Appliance Data

nstallation Requirements

Site Requirements

Ventilation

Unpacking the Appliance

Component Checklist

nstalling the Burner

Fuel Bed Layout

Fire Front

Testing & Commissioning

Operating the fire (Manual Models)

Operating the fire (Remote Models)

Page No.

Section

12.0

12.1

12.2

12.3

13.0

13.1

13.2

13.3

13.4

13.5

14.0

Contents

Spark Gap

Operating Pressure

Flue Spillage Monitoring System

Testing For Spillage

Briefing the Customer

Servicing

Cleaning the Ceramics

Removing the Burner

Servicing the Burner

Pilot Assembly

Replacing the Batteries (Remote Control Models)

Troubleshooting Guide

User nstructions

Page No.

2.0 APPLIA CE DATA

GB IE

'2013 Focal Point Fires plc.

3.0 I STALLATIO REQUIREME TS

This appliance MUST NOT be installed into a room containing a bath or shower, or where steam may be present. The fire has

been designed to fit into a builders’ opening or fireplace conforming to BS 1251 (and meeting certain dimensional requirements),

or a suitable flue box complying with the constructional requirements of BS 715. Either a ‘Replacement Chairbrick’ or a BS 1251

chairbrick should also be fitted into the builders’ opening. The flue box must be installed onto a suitable non-combustible insu-

lating surface at least 12mm thick, covering the entire base are of the box.

The flue must have an effective height of at least three meters, as measured from the hearth to the top of the flue. Any flue damper

plates or restrictors should be removed and no other restriction fitted to the flue. Where removal is not practical, the restric-

tion must be fixed in the fully open position. A natural draught flue system is required, and if previously used for solid fuel or oil

burning, the flue and chimney must be swept prior to appliance installation. The flue must be checked before installation by using

a smoke pellet or similar to ensure proper draw and that leakage is not evident at any joints. Repair and re-test as necessary

before the appliance is installed. The flue must be connected to only one fireplace, and the flue must not vent more than one appli-

ance (i.e. not shared with a gas back boiler). There must be no opening in the flue apart from the one that the appliance is installed

into, and the one venting the gases into the air. A suitable terminal may be fitted, such as class GC1, as regulations allow.

This appliance has been tested for use with circular flues of a minimum internal diameter of 175mm. The flue termination (cowl)

must be of a type suitable for use with an inset Decorative Fuel Effect Fire BS5871 part 3 contains further details.

The fireplace opening should be inspected and repairs made where nec-

essary. Any chair brick may be left in place.

The opening W DTH and HE GHT dimensions should be between

405mm and 440mm wide, and 565mm to 575mm high.

Opening DEPTH should be 220mm or greater. Opening DEPTHS

include any plaster or infill panels which form part of the installation.

This appliance requires a natural draught flue system which may be one

of the following;

• 225mm x 225mm (9in x 9in) brick or stone.

• 175mm (7in) minimum diameter lined brick or stone.

• 175mm (7in) minimum diameter twin wall flue conforming to BS 715.

Any existing under grate draught device must be sealed off.

The opening wall must be non-combustible.

The appliance requires a hearth with

non-combustible surface of at least

12mm thick.

The top surface must be at least 50mm

above the surrounding floor level, or be

surrounded by a raised edge or fender

50mm high.

4.0 SITE REQUIREME TS

A. Opening height: 565mm min/575 mm max.

B. Opening width: 405mm min/440mm max.

C. Mounting depth: 220mm

D. Hearth must extend minimum of 150mm either side of the opening.

E. Hearth must extend minimum of 300mm in front of the opening.

F. Non-combustible hearth must be a minimum of 50mm in height, or be sur-

rounded by a 50mm high fender.

‘A’

‘B’

‘C’

‘D’

‘E’

‘F’

Figure 1

Model Destination

Country Cat

Operating Pressure

(±2.0 mbar) Max Energy nput (kW) Min Energy nput (kW)

Natural gas G20 G25 G30 G31 Gross Net Gross Net

Sonora GB - E 2H 20 - - - 6.8 6.1 3.5 3.15

Specifications Manual control models Remote control models

Main burner injector Stereo size 76 Stereo size 81

Oxypilot S T 9081 S T 9081

Gas Control Copreci 21400/342 Mertik Maxitrol GV30 series

Gas nlet 8mm compression - nlet restrictor elbow 8mm compression - nlet restrictor elbow

gnition Piezo Spark Piezo Spark

Spark Gap 3.5 - 4.5mm 3.5 - 4.5mm

Flue specification

225mm x 225mm (9in x 9in) brick or stone.

175mm (7in) minimum diameter lined brick or stone.

175mm (7in) minimum diameter twin wall flue conforming to BS 715.

4.0 SITE REQUIREME TS - CO TI UED

Any type of fire surround used with this appliance must be adequately sealed to the wall and floor.

A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening.

Combustible materials, such as wood, may be fitted to within 100mm (4in) of either side of the fireplace opening , providing the forward

projection does not exceed 100mm (4in).

Any combustible side walls must be at least 500mm to the side of the radiant heat source.

As with all heating appliances, any decorations, soft furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper) positioned

too close to the appliance may discolour or scorch.

No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the same

room or space must be taken into consideration when assessing ventilation.

f spillage is detected when commissioning the appliance then amongst other problems there may be insufficient natural ventilation for

the correct operation of the flue. This is potentially a greater problem should the property be of modern nature. f the appliance does

not spill with windows open but does with windows closed, this proves that lack of ventilation is the problem, if not, it will be the flue

at fault. nstallation of an air brick in these circumstances may be the best solution. Any ventilation fitted must comply with BS 5871 part

2 and BS 5440 part 2. Ventilation located underneath or within the immediate vicinity (one metre) of the fire MUST NOT be used as it

may adversely affect the performance of the O.D.S. system.

Spillage detected during commissioning is almost always a result of poor flue performance, which cannot be corrected by any amount

of ventilation. For Republic of reland ventilation may be required, see S 813, CP3, S 327, and any other rules in force.

Read all the instructions before continuing to unpack or install this appliance.

Remove the box containing the firefront, and the bag containing the coals. Remove the cardboard packing pieces, and any bags contain-

ing other fittings or parts. Remove the burner unit from the remaining packaging.

Check that the components supplied correlate with the checklist given in section 6.1. Please dispose of the packaging materials at your

local recycling centre.

Note: Ensure that the gas supply is isolated before co encing installation of the appliance.

Smoke test the flue to ensure proper draw and that there are no leaks present.

Locate the gas supply point. This appliance is suitable for all gas connections, including those concealed behind the opening.

I portant Note: Check that the ther ocouple connection nut into the rear of the valve is secure.

Place the appliance into the shaped firebrick, ensuring it does not protrude forward of the fireplace opening. Mark the location of the

front support of the tray. Remove the tray and drill the two marked holes with an appropriate masonry bit. Place wall plugs into the

holes. Remove the front support from the appliance by unscrewing from the two front legs. Position the front foot in the over the holes

and secure the front support using suitable screws into the prepared holes. Re-fit the tray into the shaped firebrick, and secure the front

legs of the tray to the support.

Using 8mm diameter pipe, connect the appliance to the gas supply point. The appliance must be fitted with rigid or semi-rigid pipe of

8mm external diameter. The appliance is factory fitted with an inlet restrictor elbow.

Use a minimum length of 8mm pipe, less than 1.5m where possible, as a long run of pipe may cause an unacceptable drop in the supply

pressure.

GB IE

4'2013 Focal Point Fires plc.

Maxi u depth of shelf Mini u distance fro finished hearth

surface to underside of shelf

100mm 745mm

150mm 845mm

203mm 895mm

5.0 VE TILATIO

6.0 U PACKI G THE APPLIA CE

6.1 COMPO E T CHECKLIST

QUANTITY DESCRIPTION

1 Burner tray assembly.

1 Cast firefront with separate ashpan cover.

1 Moulded ceramic fibre combustion matrix.

16 ndividual ceramic coals.

1 Moulded ceramic front coal strip.

1 Set of manufacturers instructions.

1 Screw pack.

7.0 I STALLI G THE BUR ER

Please refer to the relevant section of the user manual.

Unwrap the firefront and ashpan door. Place the firefront directly in front of the fire and slide the ashpan door into place.

Do not use any firefront other than the one supplied with the appliance.

Turn on and test the gas supply up to the fire for any leaks, in accordance with current edition of BS6891.

The pilot is visible through the left hand side of ceramic fuel matrix. When cold, the coals or peb-

bles may be rotated for good viewing. The fire features a ‘twin spark’ ignition system to aid light-

ing, Push the control knob in fully and turn anti-clockwise through both of the SPARK positions,

keeping fully depressed, hold there for a few seconds. f the fire has not been used for some time,

hold the knob in this position for longer, to allow any air in the pipes to be purged.

Ensure the pilot has lit. f not, return the knob clockwise, and repeat. When the pilot lights after

one of the two sparks, keep the knob depressed in the nine o’clock position for approximately

ten seconds. Now release the knob and the pilot should stay alight. f the pilot is extinguished

during use, wait three minutes before repeating the ignition procedure.

To achieve the H GH setting, push the control knob in slightly and continue turning anti-clock-

wise to the high position. The main burner should light after a few seconds. To decrease the setting to LOW, push the knob in slightly

and turn the control knob clockwise to the low setting. To turn to the pilot only position from the H GH or LOW positions, press the

control knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep the knob pressed in, return to the off

position and release.

The pilot is visible through the left hand side of ceramic fuel matrix. When cold,

the coals or pebbles may be rotated for good viewing. Turn the main burner

control (shown in figure 3 on left hand side of control valve) knob fully anti-

clockwise.

Turn ignition knob (shown on right hand side of control valve) slightly left

towards the ignition position until reaching the stop, press down and hold for

5 seconds (only pilot gas is flowing).

Continue pressing down the knob while turning further to the left to activate

the piezo spark, continue to hold the knob down for a further 10 seconds after

the pilot has been lit. f the pilot does not light repeat the previous steps.

Upon lighting and after the further 10 seconds, release the knob and turn further to the left to

the ON position. The main burner will light and be controlled in accordance with the main burn-

er control knob setting. Adjust the main burner control knob to the desired setting.

f the pilot is extinguished during use of the fire, you MUST wait ten minutes before repeating

the ignition procedure.

To turn the main burner OFF whilst keeping the pilot flame lit, turn the ignition control knob

to the pilot position then only the pilot will remain lit.

To shut the fire off completely, press the ignition control knob down and continue turning to

the right from the pilot position to the OFF position.

A safety interlock prevents re-ignition of the pilot flame until the thermocouple has cooled suf-

ficiently to allow the magnetic valve unit to reset itself.

The remote control unit allows operation of the main burner setting between maximum and

pilot only setting. t does not permanently turn the pilot on or off.

The remote control handset incorporates an inbuilt safety feature to prevent the main burner

being activated or turned up accidentally. t is necessary to press buttons 1 and 2 (see figure 4)

simultaneously to turn the fire up.

To turn the fire down press button 3 only.

8.0 FUEL BED LAYOUT

5'2013 Focal Point Fires plc.

GB IE

9.0 FITTI G THE FIREFRO T

10.0 TESTI G A D COMMISSIO I G

11.0 OPERATI G THE FIRE (Manual Control Models)

FIN:

Figure 2

FIN:

Figure 3

Figure 4

11.1 OPERATI G THE FIRE (REMOTE CO TROL MODELS)

The gap between the spark electrode and the pilot should be 3.5 - 4.5mm to produce a good

spark.

There should be no need to adjust this. f under any circumstances the electric spark fails, the

pilot may be lit manually by proceeding with the ignition sequence as previously described, and

after turning the control knob through the spark position, the knob should be held in and the

pilot lit with a taper.

Release the pressure test point screw, and attach a pressure gauge. Light the fire on

the H GH setting. To commission the appliance, the operating pressure must be in

accordance with the figures stated in section 2.0 of these instructions. The fire is

factory set to achieve the correct flow rates at the specified inlet pressure.

Any significant variation in the inlet pressure could indicate a supply problem. f the

inlet pressure is too high, the gas supply meter/governor may be set incorrectly.

This should be checked with the fire running and if necessary reset by the gas sup-

plier. f the inlet pressure is too low, then check the meter/governor pressure with

the appliance running. f this is less than the inlet pressure stated in section 2.0 of

these instructions it will need to be reset by the gas supplier. f the inlet pressure

is too low, but the meter/governor pressure is acceptable, then a problem in the

supply pipework is to be suspected. Upon satisfactory checking of the inlet pres-

sure, turn the fire off, disconnect the pressure gauge and refit the test point screw.

Light the fire and check for gas soundness. n the event that the inlet pressure is not in accordance with the figures stated in the data

section of these instructions, the appliance must not be commissioned, and the problem investigated and rectified.

This fire is fitted with a flue spillage safety device (ODS). f the fire shuts down during use for no apparent reason then several things

may be suspected. f a door or window has been opened creating a draught, then pilot disturbance is the problem, and removal of the

draught should resolve this. f a grommet seal has been left out of the firebox (if fitted) then this also will also cause intermittent shut-

down. The gas pressure reaching the fire must also be checked. The thermocouple connection into the back of the gas control valve may

also have worked loose during installation, simply tighten to remedy if this is the case.

f pilot disturbance is not the cause, then the ODS safety system may be in operation. Switch the appliance OFF, check the flue and carry

out any remedial work required. Re-light the fire and carry out a spillage test. DO NOT allow the appliance to be used if it continues to

fail a spillage test.

The aeration hole of the pilot must be carefully cleaned out on each annual service to ensure continued function of the ODS.

The spillage monitoring system shall not be adjusted, modified, or put out of operation by the installer. Any spare parts fitted MUST be

of a type supplied for the purpose by the appliance manufacturer.

f the fire is not spilling, then further guidance should be sought, using the Troubleshooting section as a guide.

Close all doors and windows to the room containing the appliance. Let the fire run on H GH for five minutes. Take a smoke match, light

it, and using a smoke match tube, hold it at the top edge of the fire opening, 25mm down and 25mm in. Starting 50mm in from either

side, run the smoke match across the opening. All the smoke should be drawn away up the flue. Any smoke returning into the room indi-

cates that spillage is occurring. f the initial spillage test fails, run the fire for a further 10 minutes and repeat the test. When the test has

been completed satisfactorily, repeat with any extractor fans in the premises running on the highest setting, and any communicating doors

open. Finally, repeat with all doors open.

NOTE: If spillage is still indicated after undertaking all of the above, there ay be a fault in the flue, or insufficient ventila-

tion is present. f the problem cannot be rectified immediately, then expert advice should be sought. nform the user, disconnect the

fire, and attach an explanatory label.

12.0 SPARK GAP

12.1 OPERATI G PRESSURE

FIN:

Figure 5 Spark gap

FIN:

Figure 5

6'2013 Focal Point Fires plc.

12.2 FLUE SPILLAGE MO ITORI G SYSTEM

12.3 TESTI G FOR SPILLAGE

Match

Crimp

Tube

Figure 6 : Cross section of smoke match tube

Make a smoke match tube from 10mm diameter

tube. Seal off one end and crimp the tube to pre-

vent the smoke match from sliding down inside.

Spillage test - Figure 7

A.25mm down from top of

opening

B. 25mm in from front of

opening.

C. Disregard outer 50mm

either side of fireplace

opening

Fireplace Opening

Smoke Match

n Tube

Figure 7

All instructions must be handed to the user for safekeeping. Show the customer how to light and control the fire. After com-

missioning the appliance, the customer should be instructed on the safe use of the appliance and the need for regular servicing. Frequency

of service depends on usage, but MUST be carried out at least every 12 months. Advise that cleaning of the fire may be achieved when

the fire is cold using a damp cloth and mild detergent on most surfaces.

Scratched and other superficial damage to the matt black paintwork of the appliance can be covered with matching heatproof spray. Use

only the manufacturers’ recommended spray paint. Paint only when the fire is OFF and cold. Always mask off the surrounding area to

prevent contamination with overspray. Ventilate the room during the use of the spray. DO NOT attempt to spray paint the coals or

ceramics, or wash them in water.

Advise that the fire may emit a “newness” smell for a time after initial commissioning and that extra ventilation may be needed during

this time. Advise that the fire is fitted with a spillage safety device (O.D.S.). f the fire shuts down, this system may be in operation.

f spillage is suspected, SW TCH APPL ANCE OFF and call in the installer to investigate any problems.

Ensure that the fire is fully cold before attempting service. A suggested procedure for servicing is detailed below.

1. Lay out the dust sheet and tools.

2. Carefully remove the firefront casting, and ceramic components.

3. Check around the top of the fireplace opening for signs of spillage.

4. solate the gas supply at the appliance inlet elbow, and disconnect the gas supply pipe. Remove the two screws

securing the tray to the front support.

5. Lift the burner tray from the chair brick.

6. Check the flue with smoke pellet for correct operation.

7. Strip off the burner pipes and clean thoroughly.

8. Clean out the injector and pilot assembly. DO NOT attempt to dismantle the pilot unit.

9. Ensure the injector is aligned squarely with the venturi tube. Re-assemble and re-fit the burner tray.

10. Re fit and replace the ceramics, using genuine spares where necessary.

11. Re-fit the decorative front.

12. Turn on the gas supply, and leak test.

13. Check any purpose provided ventilation is un-obstructed.

14. Light the fire and test for spillage.

15. Check operating pressure and safe operation of the appliance.

For specific servicing instructions, see the relevant sections.

Remove the firefront and place to one side. Remove the ceramic components. Gently clean in the open air. Be careful not to create

dust from the coals. Where necessary replace damaged components with genuine spares. Seal scrap components in plastic bags and

dispose of at proper refuse sites as directed. Re-fit the ceramics carefully by referring to the relevant section of the user instructions.

Protect the hearth from potential damage. Remove the two screws securing the tray to the front support and withdraw from the

fireplace opening/chairbrick.

Remove the burner unit as previously described. The pilot unit can be removed by withdrawing the tubing nut, the thermocouple nut on

the rear of the valve, and the two securing screws, and lifting away. Remove the tubing nut from the valve end of the pilot pipe, and blow

through to dislodge any debris.

Remove the two tubing nuts on the ends of the gas pipe to the injector elbow and blow clear. Release the screw through the supporting

leg and lift assembly clear. The injector pipe can now be checked for debris. Remove the nut retaining the injector elbow. Blow through

the elbow to remove any debris.

12.4 BRIEFI G THE CUSTOMER

13.0 SERVICI G

GB IE

13.1 CLEA I G THE CERAMICS

13.2 REMOVI G THE BUR ER

13.3 SERVICI G THE BUR ER

'2013 Focal Point Fires plc.

Remove the burner unit as in relevant section and pilot unit as described.

Clean the pilot assembly with a soft brush and blow through. Check the aeration holes are free of any dirt or lint. Clean thoroughly

internally, the connection can be removed from the base of the pilot unit using two spanners to make cleaning easier. Do not damage

or try to remove the pilot injector. The unit is factory set and the only check necessary is to ensure the spark gap is correct. See spec-

ifications for gap setting.

Handset - Remove cover from rear of handset and insert 1 x ‘PP3’ (9 volt) battery - Replace cover

Appliance - Ensure appliance is off and cool. Remove cover from top of receiver box. The cover is protected by reflective foil, and

located towards the right hand side, underneath the burner unit. nsert 4 x ‘AA’ (1.5 volt) batteries - Replace cover.

Fire sparks but pilot does not light No gas to fire, check isolators are open.

Pipework blockage, clean out.

Air not fully purged, re-purge supply or wait longer.

Spark earthing to metal work, reset gap correctly.

Blocked pilot, clean out internally.

Pilot lights but then goes out Severe restriction in gas supply, clear obstruction.

Faulty thermocouple, replace pilot unit.

Hold control knob in for longer.

Fire does not spark at pilot HT lead detached, refit.

Spark gap too large or small, reset correctly.

Faulty piezo unit, replace.

Debris shorting out electrode, clean.

Fire runs for a ti e and then cuts off Excessive room draught or flue pull, rectify.

Loose or faulty thermocouple, rectify.

ODS system in operation.

Lint in pilot aeration hole, clean thoroughly internally

Pilot fla e shrinks when fire is on high Poor gas flow to fire, check pressure with fire on high.

f pressure is low, remove any restriction in pipework or valve.

Check all isolators are adequately sized and fully open.

Check meter pressure is adequate.

Lint in pilot aeration hole, clean thoroughly internally.

Fire s ells when first lit or in use Newness smell from brand new appliance.

Spillage occurring. Carry out spillage test and rectify any problems.

Low temperature sealants or combustible materials used in incorrect positions.

13.5 REPLACI G THE BATTERIES (REMOTE CO TROL VERSIO S)

13.4 PILOT ASSEMBLY GB IE

14.0 TROUBLESHOOTI G GUIDE

• The installation and Servicing of this fire MUST only be carried out by a competent person in accordance with local Codes

and/or Regulations, Building Regulations and the manufacturer's instructions. Failure to comply with these could lead to pros-

ecution and invalidate the appliance warranty. n the event of gas leakage from the appliance, the gas supply must be turned off

at the nearest isolating valve. This appliance is only suitable for the gas type for which it is supplied.

• Keep a note of the installer's name and address, GAS SAFE registration number and the original purchase receipt and the date

of installation. Failure to produce this information may invalidate the warranty. The appliance should be serviced regularly to

ensure continued safe operation. See the servicing section for further reference.

• Parts of this appliance become naturally hot during use. t is recommended that a suitable fireguard is used, especially where

young children, pets, the elderly or infirm are concerned. The manufacturer of this appliance considers all surfaces as working

surfaces with the exception of the control knob and ash pan door.

• As with any gas fire, a fire guard complying with BS 8423 must be used in presence of pets, children, and the

elderly or infirm.

• The appliance should be serviced regularly to ensure continued safe operation. Frequency of service will depend on use, but

MUST be carried out at least once annually.

• Combustible items, such as flooring and furniture and soft wall coverings (such as blown vinyl or embossed paper), low tem-

perature surrounds etc may discolour if fitted too close to the fire. See relevant section for further details on clearances to

combustibles. No combustible materials or flooring should protrude onto the hearth.

• This appliance incorporates a combustion monitoring system (ODS).

• DO NOT burn any foreign material on this fire, the coals must be of the correct type and laid out in accordance with the rel-

evant section of these instructions. Failure to do so could create a hazard or lead to sooting.

• The fire is only suitable for use with the gas type for which it is supplied.

• This appliance is fitted with a flue blockage safety device which will shut down the fire if abnormal flue conditions occur. t is

NOT a substitute for an independently mounted Carbon Monoxide detector.

• This fire is supplied with a particular style of firefront. Use of the firefront will ensure an adequate airflow under the firebed

for the correct functioning of this appliance. Use ONLY the firefront supplied with the appliance. Use of any other firefront

could be dangerous.

• Should any home improvements be carried out to the property after the fire is installed, such as installation of extractor fans

for example, the fire should be re-checked by a competent person for safe operation.

U S E R I S T R U C T I O S

2.0 CLEARA CES TO COMBUSTIBLES

A combustible shelf may be fixed to the wall above the fire, providing that it complies with the dimensions given below.

A non-combustible shelf may be fitted to within 10mm of the top edge of the fireplace opening.

Combustible materials, such as wood, may be fitted to within 100mm of either side of the fireplace opening, providing the for-

ward projection does not exceed 100mm.

Any combustible side walls must be at least 500mm to the side of the radiant heat source.

As with all heating appliances, any decorations, soft furnishings, and wall coverings (i.e. flock, blown vinyl and embossed paper)

positioned too close to the appliance may discolour or scorch.

1.0 IMPORTA T OTES

1'2013 Focal Point Fires plc.

GB IE

Maxi u depth of shelf Mini u distance fro finished hearth

surface to underside of shelf

100mm 745mm

150mm 845mm

203mm 895mm

Section

1.0

2.0

3.0

4.0

5.0

6.0

6.1

7.0

8.0

Contents

mportant Notes

Clearances To Combustilbles

Fire Guards

Servicing

Ventilation

Operating The Fire (Manual Control Versions)

Operating The Fire (Remote Control Versions)

Flue Spillage Monitoring Systerm

Fuel Bed Layout (Coal Effect)

Page No.

Section

8.1

8.2

9.0

10.0

11.0

12.0

13.0

14.0

Contents

Fuel Bed Layout (Pebble Effect)

Fuel Bed Layout (Log Effect)

Cleaning

Replacing The Batteries (Remote

Control Versions)

List Of Replacement Parts

nstallation Details

Service History

Guarantee

Page No.

The fireguards specified in BS 8423 are intended to protect people from falling into a fire, prevent burns and reduce the risk of

injury, particularly to young children and the infirm. n addition it is intended to reduce the risk of fire resulting from clothing

and/or other flammable materials coming into contact with, or in proximity to, burning fuel and/or hot surfaces.

Fireguards can be permanently fixed in position or can be moveable, and can incorporate open fires including combination grates,

or closed fires, including room heaters and stoves. See figures 1 & 2 for fireguard examples.

The fireguards specified are not intended to reduce the risk of fires caused by flying particles, which are covered by BS 3248.

The fire and flue should be checked on an annual basis to ensure all of the product of combustion are entering the flue and that

there is no excessive build up of soot. The frequency of service will depend on usage, but MUST be carried out every 12 months.

Servicing must be carried out by a GAS SAFE registered person.

Cleaning of the coals may be carried out by following the instructions given in the nstallation section. The nstallation instructions

carry full servicing details for the use of the installer.

f debris from the flue or other foreign matter is found on the fire it may indicate a need for servicing. Do not use the fire until

the source of the debris has been found and rectified. Air vents (where fitted) should be checked periodically to ensure they are

free from obstruction.

No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the

same space or room, and the results of a spillage test must be taken into consideration when assessing ventilation requirements,

this will have been carried out by your registered installer.

For Republic of reland, ventilation may be required, see S 813, CP3, S 327, and any other rules in force.

WAR I G : Ventilation openings (where fitted) must never be blocked or restricted in any way.

3.0 FIRE GUARDS GB IE

Figure 1

Example of moveable fireguard for portable heating appliances

Key

1. Optional base section for total enclosure of a wall mounted appliance

2. Points for attachment to a wall.

Figure 2

Example of detachable fireguard

Key

1. Detachable fireguard

2. Screw eye

4.0 SERVICI G

5.0 VE TILATIO

2'2013 Focal Point Fires plc.

This manual suits for next models

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point SAN FRANCISCO CHARLESTON Assembly Instructions

Focal Point

Focal Point AVANT User guide

Focal Point

Focal Point KAVACHI F500181 Assembly Instructions

Focal Point

Focal Point NOIR L23 Assembly Instructions

Focal Point

Focal Point POLARIS User manual

Focal Point

Focal Point HORIZON Guide

Focal Point

Focal Point P23 EBONY NG - F500229 Assembly Instructions

Focal Point

Focal Point EVOKE LED ELECTRIC Assembly Instructions

Focal Point

Focal Point AMERSHAM LED ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point L27G Guide

Focal Point

Focal Point PANORAMIC COMPLETE ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point Ebony LED Electric Fire Assembly Instructions

Focal Point

Focal Point OBLIQUE Guide

Focal Point

Focal Point Excelsior Fanflue User guide

Focal Point

Focal Point EF11-36 PASADENA Assembly Instructions

Focal Point

Focal Point Charmouth Assembly Instructions

Focal Point

Focal Point L30 PIANO NG Assembly Instructions

Focal Point

Focal Point EF461L-E Assembly Instructions

Focal Point

Focal Point BLENHEIM STYLE Guide

Focal Point

Focal Point LJSF4009E-EHS88 Assembly Instructions

Focal Point

Focal Point AVONBURY CUBE LED ELECTRIC COMPLETE SUITE... Assembly Instructions

Focal Point

Focal Point LULWORTH Guide

Focal Point

Focal Point Fuego User guide

Focal Point

Focal Point ExcelsiorRadiant MAN User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual