Fluke 362 User manual
362
Clamp Meter
Users Manual
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for two years
from the date of purchase. This warranty does not cover fuses, disposable batteries, or
damage from accident, neglect, misuse, alteration, contamination, or abnormal
conditions of operation or handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. To obtain service during the warranty period, contact your
nearest Fluke authorized service center to obtain return authorization information, then
send the product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS
FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE
IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR
THEORY. Since some states or countries do not allow the exclusion or limitation of an
implied warranty or of incidental or consequential damages, this limitation of liability
may not apply to you.
i
Table of Contents
Title Page
Introduction................................................................................................................. 1
Contact Fluke ............................................................................................................. 2
Safety Information ...................................................................................................... 3
The Meter ................................................................................................................... 11
Specifications ............................................................................................................. 17
Electrical Specifications.......................................................................................... 17
Mechanical Specifications ...................................................................................... 18
Environmental Specifications ................................................................................. 19
Safety Specifications .............................................................................................. 20
362
Users Manual
ii
1
Introduction
Warning
Read "Safety Information" before you use the Meter.
The Fluke 362 is a hand-held, battery-operated clamp meter (the Meter) that measures:
•ac and dc current and voltage
•resistance
•continuity
The Meter ships with:
•TL75 test leads
•two AAA batteries (installed)
•362 User Manual
Clamp Meter
Safety Information
3
Safety Information
A Warning identifies conditions and actions that pose hazard(s) to the user. A Caution identifies
conditions and procedures that could cause Meter damage, equipment under test damage, or
permanent loss of data.
Symbols used on the Meter and in this manual are explained in Table 1.
Warning
To prevent possible electrical shock or personal injury, follow these guidelines:
•Use the Meter only as specified in this manual or the protection provided by the
Meter can be compromised.
•Examine the case before you use the Meter. Look for cracks or missing plastic.
Carefully look at the insulation around the connectors.
•Never measure current while the test leads are inserted into the input jacks.
•Make sure the battery door is closed and latched before operating the Meter.
362
Users Manual
4
•Remove the test leads from the Meter before the battery door is opened.
•Examine the test leads for damaged insulation or exposed metal. Check test lead
continuity. Replace damaged test leads before using the Meter.
•Do not use the Meter if it operates incorrectly. Protection can be compromised.
When in doubt, have the Meter serviced.
•Do not use the Meter around explosive gas, vapor or in damp or wet
environments.
•Use only type AAA batteries, properly installed in the Meter case, to power the
Meter.
•When batteries are changed, make sure the calibration seal in the battery
compartment is not damaged. If damaged, the Meter may not be safe to use.
Return the Meter to Fluke for replacement of the seal.
•When measuring, keep fingers behind the Tactile Barrier. See "The Meter" .
Clamp Meter
Safety Information
5
•To avoid false readings that can lead to electrical shock and injury, replace the
batteries as soon as the low battery indicator () appears.
•When servicing the Meter, use only specified replacement parts.
•Have the Meter serviced only by qualified service personnel.
•Be careful around voltages > 30 V ac rms, 42 V ac peak, or 60 V dc. Such
voltages pose a shock hazard.
•Do not apply more than the rated voltage, as marked on the Meter, between the
terminals or between any terminal and earth ground.
•When using the probes, keep fingers behind the finger guards on the probes.
•Connect the common test lead before connecting the live test lead. When
disconnecting test leads, disconnect the live test lead first.
•Do not work alone so assistance can be rendered in an emergency.
362
Users Manual
6
•Use extreme caution when working around bare conductors or bus bars. Contact
with the conductor could result in electric shock.
•Adhere to local and national safety codes. Individual protective equipment must
be used to prevent shock and arc blast injury where hazardous live conductors
are exposed.
•Disconnect circuit power and discharge all high-voltage capacitors before you
do diode tests or measure resistance or continuity.
•Do not measure ac/dc current in circuits carrying more than 600 V or 200 A with
the Meter Jaw.
•Never operate the Meter with the back cover removed or the case open.
•Remove the batteries if the Product is not used for an extended period of time, or
if stored in temperatures above 50 °C. If the batteries are not removed, battery
leakage can damage the Product.
Clamp Meter
Safety Information
7
•Measure a known voltage first to make sure that the Product operates correctly.
•Only use probes, test leads, and accessories that have the same measurement
category, voltage, and amperage ratings as the Product.
•Use Product-approved measurement category (CAT), voltage, and amperage
rated accessories (probes, test leads, and adapters) for all measurements.
•Do not exceed the Measurement Category (CAT) rating of the lowest rated
individual component of a Product, probe, or accessory.
Caution
To avoid possible damage to the Meter or to equipment under test:
•Use the proper jacks, function, and range for the measurement application.
•Clean the case and accessories with a damp cloth and mild detergent only. Do
not use abrasives or solvents.
Table of contents
Other Fluke Measuring Instrument manuals
Fluke
Fluke PM6690 User manual
Fluke
Fluke 416D User manual
Fluke
Fluke 1550 User manual
Fluke
Fluke FI-500 FiberInspector Micro User manual
Fluke
Fluke i3000s Flex Series User manual
Fluke
Fluke i6000s Flex Series User manual
Fluke
Fluke Hart Scientific 914 Series User manual
Fluke
Fluke VR1710 User manual
Fluke
Fluke ScopeMeter 199B User manual
Fluke
Fluke 377 Use and care manual
Fluke
Fluke NORMA 4000 Operators User manual
Fluke
Fluke 80K-4 User manual
Fluke
Fluke 175 User manual
Fluke
Fluke 55XXA/COIL 50 User manual
Fluke
Fluke ProcessMeter 787 Original instructions
Fluke
Fluke 726 Configuration guide
Fluke
Fluke 1653B User manual
Fluke
Fluke 165X User manual
Fluke
Fluke 377 Use and care manual
Fluke
Fluke 3210-PR-TF User manual
