EUTECH INSTRUMENTS TDScan Low User manual

INC

DEC

•Waterproof & Floats

•ReplaceableElectrode

•Auto-off

•AutomaticTemperature

Compensation(ATC)

Diagram 1

Openthisleafletforcalibration/testing/maintenance

instructions.

Changing Batteries

1. Open battery

compartment

lid (with

attached

lanyardloop).

2. Remove old

batteries;

replace

with fresh

ones. Note

polarity as

showninbatterycompartment.SeeDiagram1.

3. Recalibrateafterbatterychange.

Warranty

Eutech Instruments warrants its meter free from

manufacturing defects for 2 years and electrode

module for 6 months. If repair, adjustment or

replacementisnecessaryandhasnotbeentheresult

of abuse or misuse within the time period, please

returnthetester–freightprepaid–andcorrection

willbemadewithoutcharge.Outofwarrantyproducts

will be repaired on a charge basis.

Return Of Items

Authorization must be obtained from Eutech’s

distributor before returning items for any reason.

When applying for authorization, please include

informationregardingthereasontheitem(s)areto

bereturned.

Note:Wereservetherighttomakeimprovementsin

design, construction and appearance of products

withoutnotice.Pricesaresubjecttochangewithout

notice.

Waterproof ECScan High Instructions

Before You Begin

Removeelectrodecap.Soakelectrodeforafew

minutes in alcohol to remove oils.

Calibration

Tester is factory calibrated. However, to ensure

accuracy,calibrateconductivityonaregularbasis.

Selectacalibrationstandardappropriateforthe

ECScan High tester (between 2.00 mS and

19.90mS).Itisbesttoselectastandardclose

tothetestsolutionvalue.

1. Open battery compartment lid (end with

lanyardloop).

2. Orientate the battery compartment as

showninDiagram1.

3.Rinseelectrodeindeionizedwater,then

rinseitincalibrationstandard,thendip it

intoacontainer ofcalibrationstandard.

4. Switch unit on (ON/OFF key). Wait

severalminutesfordisplaytostabilize.

5. Pressthe INCorDEC keyto adjust

reading to match the calibration

standardvalue.

6. After3secondswithoutakeypress,

the display flashes 3 times, then

shows ‘ENT’. The tester accepts

calibration value; returns to

measurementmode.

7. Replacebattery cap.

Conductivity Testing

1. Removeelectrode cap.Switch uniton(ON/OFF

key).

2. Dipelectrodeintotestsolution.Makesuresensor

is fully covered.

3. Wait for reading to stabilize (Automatic

Temperature Compensation corrects for

temperaturechanges).Notereading.

4. PressON/OFFtoturnoff tester.Replaceelectrode

cap. Note: Tester automatically shuts off after

8.5 minutes of non-use.

HOLD Function

PressHOLDkeytofreezedisplay.PressHOLDagain

torelease.

Tester Maintenance

• To improve performance, clean the electrode

byrinsingtheminalcoholfor10to15minutes.

• Replace all batteries if low battery indicator

appears,or ifreadings arefaint orunstable.

• Ifyouexperience drift,periodicallylet electrode

fully dry.

When you need a new electrode, see “Electrode

Replacement” on insert in back of box.

Self-Diagnostic MessagesSelf-Diagnostic Messages

Self-Diagnostic Messages

bAt Weakbatteries–replacewithfreshonesspecified

bymanufacturer.

Err Wrong keypress.

Or,Ur Overrange/Underrangesignal,orelectrode

isnotincontactwithsolution,orelectrodeisfailing.

---- Calibrationmodeactivatedbutnotperformed.

68X247755 11/00 Rev 0

•Waterproof & Floats

•ReplaceableElectrode

•Auto-off

•AutomaticTemperature

Compensation(ATC)

INC

DEC

Diagram 1

Openthisleafletforcalibration/testing/maintenance

instructions.

Changing Batteries

1. Open battery

compartment

lid (with

attached

lanyardloop).

2. Remove old

batteries;

replace with

fresh ones.

Note polarity

as shown in

batterycompartment.See Diagram1.

3. Recalibrateafterbatterychange.

Warranty

Eutech Instruments warrants its meter free from

manufacturing defects for 2 years and electrode

module for 6 months. If repair, adjustment or

replacementisnecessaryandhasnotbeentheresult

of abuse or misuse within the time period, please

returnthetester–freightprepaid–andcorrection

willbemadewithoutcharge.Outofwarrantyproducts

will be repaired on a charge basis.

Return Of Items

Authorization must be obtained from Eutech’s

distributor before returning items for any reason.

When applying for authorization, please include

informationregardingthereasontheitem(s)areto

bereturned.

Note:Wereservetherighttomakeimprovementsin

design, construction and appearance of products

withoutnotice.Pricesaresubjecttochangewithout

notice.

Waterproof ECScan Low Instructions

68X247754 11/00 Rev 0

Conductivity Testing

1. Removeelectrode cap.Switchunit on(ON/OFF

key).

2. Dip electrode into test solution. Make sure

sensor is fully covered.

3. Wait for reading to stabilize (Automatic

Temperature Compensation corrects for

temperaturechanges).Notereading.

4. Press ON/OFF to turn off tester. Replace

electrode cap. Note: Tester automatically

shuts off after 8.5 minutes of non-use.

HOLD Function

PressHOLDkeytofreezedisplay.PressHOLDagain

torelease.

Tester Maintenance

••

• To improve performance, clean the electrode

byrinsingtheminalcoholfor10to15minutes.

• Replace all batteries if low battery indicator

appears,or ifreadings arefaint orunstable.

• Ifyouexperiencedrift,periodicallyletelectrode

fully dry.

When you need a new electrode, see “Electrode

Replacement” on insert in back of box.

Self-Diagnostic MessagesSelf-Diagnostic Messages

Self-Diagnostic Messages

bAt Weak batteries–replace with fresh ones

specified by manufacturer.

Err Wrong keypress.

Or,Ur Overrange/Underrangesignal,orelectrode

isnotincontactwithsolution,orelectrodeisfailing.

---- Calibrationmodeactivatedbutnotperformed.

Before You Begin

Removeelectrodecap.Soakelectrodeforafew

minutes in alcohol to remove oils.

Calibration

Tester is factory calibrated. However, to ensure

accuracy,calibrateconductivityonaregularbasis.

Selectacalibrationstandardappropriateforthe

ECScan Low tester (between 200 µS and

1990 µS).Itisbesttoselectastandardclose

tothetestsolutionvalue.

1. Open battery compartment lid (end with

lanyardloop).

2. Orientate the battery compartment as

showninDiagram1.

3.Rinseelectrodeindeionizedwater,then

rinseitincalibrationstandard,thendipit

intoacontainer ofcalibrationstandard.

4. Switch unit on (ON/OFF key). Wait

severalminutesfordisplaytostabilize.

5.PresstheINCorDECkeytoadjust

reading to match the calibration

standardvalue.

6. After 3 seconds without a key

press, the display flashes 3 times,

thenshows‘ENT’.Thetesteraccepts

calibration value; returns to

measurementmode.

7. Replacebattery cap.

Tester TDScan TDScan ECScan ECScan

Low High Low High

Range 0to 0to 0to 0to

1990 10.00 1990 19.90

ppm ppt µS/cm mS/cm

Resolution 10 0.10 10 0.10

ppm ppt µS/cm mS/cm

Accuracy ±1% Full Scale

TDSfactor 0.4 to 1.0 selectable -

Calibration 200to 2.00to 200to 2.00to

Standard 1990 10.00 1990 19.90

Range ppm ppt µS/cm mS/cm

Calibration 1 point (calibration range is ±30%

of factory default parameter)

ATC 0 to 50 °C

Temp 2% per °C

Coefficient

Operating 0to50°C

Temp

Power Four X 1.5V

Battery (Type:A76,LR 44 or V136A);

> 140 hrs continuous use

Dimension; Tester: 16.5 cmx 3.8 cm;90 g

Weight Boxed: 22 cm x6 cm x 5 cm; 170 g

•Push-buttoncalibration

•Fast,stable,repeatablereadings

•Availablethroughauthorizeddistributors

SPECIFICATIONS

Lanyard

connection

Replaceable

Sensor

Twist-off

Battery

Compartment

ManufacturedBy:

EutechInstrumentsPteLtd

Blk 55, Ayer Rajah Crescent,

#04-14/24, Singapore 139949

Tel: (65)778 6876 Fax: (65)773 0836

E-Mail: [email protected]

Web-Site: http://www.eutechinst.com

MadeinSingapore

68X247828 11/00 Rev 0

REMOVE THE OLD ELECTRODE

REPLACE THE ELECTRODE

(PictureB)

(PictureA)

You can replace the electrode module

at the fraction of the cost of a new

tester. When the tester fails to calibrate

or gives fluctuating readings in

calibration standards, you need to

change the electrode.

1. With dry hands, grip the ribbed tester

collar with electrode facing you. Twist

the collar counter clockwise (see picture

A). Save the ribbed tester collar and

O-ring for later use.

2. Pull the old electrode module away from

the tester.

3. Align the four tabs on the new module

so that they match the four slots on the

tester (see picture B).

4. Gently push the module onto the slots

to sit it in position. Push the smaller

O-ring fully onto the new electrode

module. Push the collar over the module

and thread it into place by firmly twisting

clockwise.

Electrode Replacement

Water quality testing • water and

Wastewater treatment • hydroponics

• pools • boilers • factories • ecology

studies • and more!

Applications

This manual suits for next models

Table of contents

Other EUTECH INSTRUMENTS Measuring Instrument manuals

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS POTASSIUM EPOXY User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS PC 700 User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ECOSCAN CON TDS 5 CONDUCTIVITY PORTABLE... Assembly instructions

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN DO 5000 DO METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS Ion 700 User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS WATERPROOF CYBERSCAN PH 300310 PHMV METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS TURBIDIMETER TN-100 WATERPROOF PORTABLE... User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ECOSCAN ION 6 IONPHMV METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PC 10 COMBINATION PHCONDUCTIVITY... User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PHION 510 PHION METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PH 10002500 PHION METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PH 110 PHMVRS232 METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS WATERPROOF EC User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS Oakton 450 Series User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PH ION 510 PH ION BENCH METER Mounting instructions

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN DO 100 DISSOLVED OXYGEN METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ION 700 - REV 3 User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS SODIUM GLASS User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS CYBERSCAN PC 5000 PHCONDUCTIVITY METER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS FLUORIDE EPOXY User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ION 6 PLUS PH ION MV TEMP User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS DO 6PLUS DISSOLVED OXYGEN TEMP User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS WATERPROOF C401 COLORIMETER User manual

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ?lpha-CON550 User manual

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Endress+Hauser

Endress+Hauser Deltabar FMD71 technical information

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Endress+Hauser

Endress+Hauser Proline Promag 50 Brief operating instructions

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual