Installation and Operation Manual – SILOTEC 8000 Table of Contents
Doc.-ID: SILOTEC_11022020_EN 3
Table of Contents
1System Description 4
1.1System Overview of the SILOTEC 8000 .............4
1.2Measuring Principles...........................................5
1.3Intended Use....................................................... 5
1.4Safety Hazards....................................................6
1.5Disruption of the Process ....................................6
1.6Storage instructions ............................................6
1.7Name Plates .......................................................7
1.8System description – Contents of GRP housing .8
2Installation 9
2.1Installation requirements for electronic unit.........9
2.2Installation of probe signal cable FEP-0007/8...10
2.3Access to the Terminals....................................11
2.4Ferrite Sleeves (EMC).......................................11
2.5Wiring diagram of the Electronic Unit ................12
2.6Wiring Diagram of the SILOTEC 8000 ..............13
2.7Gas Plans .........................................................16
2.8Installation of the probe.....................................18
2.9Mounting the Probe...........................................18
2.10Electrical Connections of the Cuvette ...............19
2.11Requirements for Pneumatic Cable FEP-0002 .19
2.12Preparation of the pneumatic Cable..................20
2.13Connections at the probe ..................................20
2.14Pneumatic Connections of Electronic Units ......21
3Initial Operation 22
3.1Checklist before commissioning the system .....22
3.2System Power Up .............................................22
3.3Display - Probe Heating Phase .........................23
3.4Display - Measuring Mode ................................23
3.5Keypad and Display ..........................................23
3.6Status LEDs ......................................................24
3.7Softkey Symbols ...............................................24
3.8System Code.....................................................24
4Software Overview and Explanations 25
4.1Software Overview - SYS-MENU ...................... 25
4.2Software Explanations - SYS-MENU ................29
4.2.1O2Measuring Ranges (Scaling)........................29
4.2.2Limit alarm settings ...........................................29
4.2.3O2Sensor calibration values.............................29
4.2.4Measuring value averaging for O2/ COe...........29
4.2.5mA output on system errors (O2/ COe).............29
4.2.6COeMeasuring Ranges (Scaling) .....................30
4.2.7COeSensor Calibration values..........................30
4.2.8Time per test gas apply.....................................30
4.2.9Delay time to process........................................30
4.2.10Pre-purge time ..................................................30
4.2.11Automatic Calibration (ACAL) ...........................30
4.2.12ENOTEC REMOTE...........................................31
4.2.13Measuring units.................................................31
4.2.14Language ..........................................................32
4.2.15Change system code ........................................32
4.2.16Load factory settings .........................................32
4.2.17Set COemeasurement to off/on ........................32
4.2.18Service.............................................................. 32
4.3System Checks................................................. 33
4.4CAL MENU ....................................................... 34
4.4.1Calibration Menu - Display Overview................ 34
4.4.21-point calibration (O2and/or COe) (manual) .... 35
4.4.32-point calibration (O2and/or COe) (manual) .... 35
5Service and Maintenance 36
5.1Exchange fuses ................................................ 36
5.2Pressure and flow rates .................................... 36
5.3Position of the adjustment valves ..................... 37
5.4Adjusting Flow Rate (SME-54 19” rack)............ 37
5.5Adjusting the sample gas extraction rate .......... 38
5.6Working on the Meauring Cuvette .................... 38
5.6.1Replace the probe inner part ............................ 39
5.6.2Replace the probe tube with O2sensor ............ 40
5.6.3Replace the COesensor ................................... 40
5.6.4Seal the COesensor guide tube........................ 41
5.7Blow-back (optional) ......................................... 41
5.8Relay Outputs / Functions and Correlation ....... 42
6Status Messages 43
6.1Error Messages ................................................ 43
6.2Alarm Messages ............................................... 45
6.3Service Messages ............................................ 45
7Troubleshooting 46
ATechnical Data 48
A.1Technical Specifications SME-53 Electronic Unit
.......................................................................... 48
A.2Technical Specifications - Probes ..................... 49
A.3Requirements of the Gas Supply ...................... 50
BDimensional drawings 51
B.1Electronic units dimensions ............................. 51
B.2Probe dimensions ............................................. 52
B.3Probe inner part SIK-0501 ................................ 52
CSILOTEC 8000 spare parts 53
C.1Overview........................................................... 53
C.2Mounting Plates of SME-53 Electronic Unit ...... 54
C.3Mounting Plates of 19" Rack SME-54............... 54
C.4Display Board ................................................... 55
DWarranty 56
EDeclaration of Conformity 57
Index 58
