Endress+Hauser FMB70 User manual

Products Solutions Services

Brief Operating Instructions

Deltapilot S FMB70

Hydrostatic level measurement

These Brief Operating Instructions are not a substitute for the

Operating Instructions pertaining to the device.

Detailed information about the device can be found in the

Operating Instructions and the additional documentation.

Available for all device versions via

• Internet: www.endress.com/deviceviewer

• Smartphone/tablet: Endress+Hauser Operations app

KA01020P/00/EN/17.22-00

71566247

2022-04-05

Associated documentation Deltapilot S FMB70

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Document function

The Brief Operating Instructions contain all the essential information from incoming

acceptance to initial commissioning.

Deltapilot S FMB70 About this document

Endress+Hauser 3

2.2 Symbols used

2.2.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.2.2 Electrical symbols

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding

system.

Protective earth (PE)

Ground terminals that must be connected to ground prior to establishing any other

connections.

The ground terminals are located on the interior and exterior of the device:

• Interior ground terminal: protective earth is connected to the mains supply.

• Exterior ground terminal: device is connected to the plant grounding system.

2.2.3 Symbols for certain types of information and graphics

Permitted

Procedures, processes or actions that are permitted

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Reference to page

Reference to graphic

Basic safety instructions Deltapilot S FMB70

4 Endress+Hauser

Visual inspection

Notice or individual step to be observed

1, 2, 3, ...

Item numbers

A, B, C, ...

Views

2.3 Registered trademarks

KALREZ®

Trademark of E.I. Du Pont de Nemours & Co., Wilmington, USA

TRI-CLAMP®

Trademark of Ladish & Co., Inc., Kenosha, USA

HART®

Registered trademark of the FieldComm Group, Austin, USA

GORE-TEX®

Trademark of W.L. Gore & Associates, Inc., USA

3 Basic safety instructions

3.1 Requirements for the personnel

Personnel must meet the following requirements for their tasks:

‣Trained, qualified specialists must be suitably qualified to perform this function and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣Before starting work, read and understand the instructions in the manual and

supplementary documentation as well as the certificates (depending on the application)

‣Follow instructions and comply with basic conditions

3.2 Intended use

The Deltapilot S is a hydrostatic pressure sensor for measuring level and pressure.

3.2.1 Foreseeable incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability.

Deltapilot S FMB70 Basic safety instructions

Endress+Hauser 5

3.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

‣Switch off the supply voltage before connecting the device.

3.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

‣If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability:

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous

area (e.g. explosion protection, pressure vessel safety):

‣Based on the nameplate, check whether the ordered device is permitted for the intended

use in the hazardous area.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

3.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the- art safety requirements, has been tested, and left the factory in a condition in which

they are safe to operate.

It fulfills general safety requirements and legal requirements. It also conforms to the EC

directives listed in the device-specific EC declaration of conformity. Endress+Hauser confirms

this fact by applying the CE mark.

3.6 Functional safety SIL3 (optional)

The Functional Safety Manual must be strictly observed for devices that are used in functional

safety applications.

Incoming acceptance and product identification Deltapilot S FMB70

6 Endress+Hauser

4 Incoming acceptance and product identification

4.1 Incoming acceptance

DELIVERY NOTE

1 = 2

A0016870

• Is the order code on the delivery note (1) identical to the order code on the product sticker

(2)?

• Are the goods undamaged?

• Do the data on the nameplate correspond to the order specifications and the delivery note?

• Is the documentation available?

• If required (see nameplate): Are the safety instructions (XA) present?

If one of these conditions is not fulfilled, please contact your Endress+Hauser sales office.

4.2 Product identification

The device can be identified in the following ways:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣Enter serial number from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer)

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

‣Enter the serial number from the nameplate in the Endress+Hauser Operations app or scan

the 2-D matrix code on the nameplate with the camera

 All of the information on the measuring device and on the scope of the technical

documentation pertaining to the device is displayed.

4.3 Storage and transport

4.3.1 Storage conditions

Use original packaging.

Store the measuring device in clean and dry conditions and protect from damage caused by

shocks (EN 837-2).

Deltapilot S FMB70 Mounting

Endress+Hauser 7

5 Mounting

5.1 Mounting requirements

5.1.1

Dimensions → see the Technical Information for Deltapilot S TI00416P, "Mechanical

construction" section.

5.1.2 General installation instructions

• Devices with a G 1 1/2 thread:

When screwing the device into the tank, the flat seal has to be positioned on the sealing

surface of the process connection. To avoid additional strain on the process membrane, the

thread should never be sealed with hemp or similar materials.

• Devices with NPT threads:

• Wrap Teflon tape around the thread to seal it.

• Tighten the device at the hexagonal bolt only. Do not turn at the housing.

• Do not overtighten the thread when screwing. Max. tightening torque:

20 to 30 Nm (14.75 to 22.13 lbf ft)

5.2 Mounting the device

• Due to the orientation of the Deltapilot S, a zero point shift may occur, i.e. when the vessel

is empty, the measured value does not display zero. You can correct this zero point shift

either directly on the device via the  button or via remote operation.

• To ensure optimum readability of the local display, it is possible to rotate the housing by up

to 380°.

• The local display can be rotated in 90° stages.

• Endress+Hauser offers a mounting bracket for installation on pipes or walls.

5.2.1 Installation instructions

NOTICE

Damage to the device!

If a heated device is cooled during a cleaning process (e.g. by cold water), a vacuum develops

for a short time and, as a result, moisture can enter the sensor through the pressure

compensation element (1).

‣Mount the device with the pressure compensation element (1) pointing diagonally

downwards or to the side as much possible.

Mounting Deltapilot S FMB70

8 Endress+Hauser

A0031804

• Keep the pressure compensation and GORE-TEX® filter (1) free from contamination and

water.

• Do not clean or touch process membranes with hard or pointed objects.

• The device must be installed as follows in order to comply with the cleanability

requirements of the ASME-BPE (Part SD Cleanability):

A0031805

Deltapilot S FMB70 Mounting

Endress+Hauser 9

Level measurement

• Always install the device below the lowest measuring point.

• Do not install the device at the following positions:

• In the filling curtain

• In the tank outlet

• In the suction area of a pump

• At a point in the tank which could be affected by pressure pulses from the agitator

• The adjustment and functional test can be carried out more easily if you mount the device

downstream from a shutoff device.

• The Deltapilot S must also be insulated in the case of media that can harden when cold.

Pressure measurement in gases

Mount the Deltapilot S with shutoff device above the tapping point so that any condensate

can flow into the process.

Pressure measurement in vapors

• Mount the Deltapilot S with the water pocket pipe above the tapping point.

• Fill the water pocket pipe with liquid before commissioning. The water pocket pipe reduces

the temperature to almost ambient temperature.

Pressure measurement in liquids

Mount the Deltapilot S with the shutoff device below or at the same level as the tapping point.

5.2.2 Turning the housing

The housing can be rotated by up to 380° by loosening the setscrew.

T14 T15 T17

A0019996

1. T14 and T15 housing: loosen the setscrew with a 2 mm (0.08 in) Allen key. T17

housing: loosen the setscrew with a 3 mm (0.12 in) Allen key.

2. Rotate the housing (max. up to 380°).

3. Retighten the setscrew with 1 mm (0.74 lbf ft)1 Nm (0.74 lbf ft).

Electrical connection Deltapilot S FMB70

10 Endress+Hauser

5.2.3 Closing the housing covers

NOTICE

Devices with EPDM cover seal - leaking transmitter!

Mineral-, animal- or plant-based lubricants cause the EPDM cover seal to swell and the

transmitter to leak as a result.

‣It is not necessary to grease the thread due to the coating applied to the thread at the

factory.

NOTICE

The housing cover can no longer be closed.

Damaged thread!

‣When closing the housing covers make sure that the threads on the covers and the housing

are free from dirt, such as sand. If you encounter resistance when closing the covers, then

check the threads again for dirt.

Closing the covers on the hygienic stainless steel housing (T17)

The covers for the terminal compartment and electronics compartment are hooked into the

housing and closed with a screw in each case. These screws must be tightened finger-tight (2

Nm (1.48 lbf ft)) to the stop to ensure that the covers are securely seated and leak-tight.

6 Electrical connection

6.1 Connecting the device

LWARNING

Risk of electric shock!

If the operating voltage is > 35 VDC: Dangerous contact voltage at terminals.

‣In a wet environment, do not open the cover if voltage is present.

LWARNING

An incorrect connection compromises electrical safety!

‣

• Risk of electric shock and/or explosion! Switch off the supply voltage before connecting the

device.

• When using the measuring device in hazardous areas, installation must also comply with

the applicable national standards and regulations and the Safety Instructions or Installation

or Control Drawings.

• Devices with integrated overvoltage protection must be grounded.

• Protective circuits against reverse polarity, HF influences and overvoltage peaks are

integrated.

• The supply voltage must match the power supply on the nameplate, see Operating

Instructions.

• Switch off the supply voltage before connecting.

• Remove the housing cover of the terminal compartment.

Table of contents

Other Endress+Hauser Measuring Instrument manuals

Endress+Hauser

Endress+Hauser Liquiphant FTL63 User manual

Endress+Hauser

Endress+Hauser Levelflex M FMP45 User manual

Endress+Hauser

Endress+Hauser CPM280 User manual

Endress+Hauser

Endress+Hauser Proline Promag W 400 User manual

Endress+Hauser

Endress+Hauser Proline Prosonic Flow93C Application guide

Endress+Hauser

Endress+Hauser Raman Rxn2 User manual

Endress+Hauser

Endress+Hauser Levelflex FMP53 User manual

Endress+Hauser

Endress+Hauser OUSAF44 User manual

Endress+Hauser

Endress+Hauser Proline Promass A 100 User manual

Endress+Hauser

Endress+Hauser Smartec S CLD134 User manual

Endress+Hauser

Endress+Hauser Levelflex FMP51 User manual

Endress+Hauser

Endress+Hauser HART Proline Promag 51 User manual

Endress+Hauser

Endress+Hauser Proline Promass I 300 PROFIBUS PA User manual

Endress+Hauser

Endress+Hauser Proline Promass 80H Manual

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Technical specifications

Endress+Hauser

Endress+Hauser Micropilot NMR84 Technical specifications

Endress+Hauser

Endress+Hauser Liquiphant FTL62 Technical specifications

Endress+Hauser

Endress+Hauser Liquiline System CA80NO User manual

Endress+Hauser

Endress+Hauser TOC Analyzer CA79 User manual

Endress+Hauser

Endress+Hauser Prosonic S FMU90 PROFIBUS DP User manual

Endress+Hauser

Endress+Hauser silopilot FMM 460 User manual

Endress+Hauser

Endress+Hauser Proline Promag H 100 EtherNet/IP User manual

Endress+Hauser

Endress+Hauser SpectraSensors OXY5500 User manual

Endress+Hauser

Endress+Hauser Proline Prowirl O 200 Technical specifications

Popular Measuring Instrument manuals by other brands

Suaoki

Suaoki D40 user manual

Elster

Elster BK-G1.6 operating instructions

Duratool

Duratool D03128 manual

Vega

Vega VEGAPULS 65 Quick setup guide

Tonghui

Tonghui TH2618B Operation manual

Tenmars

Tenmars TM-801 user manual

MSR

MSR 145 user manual

TPS

TPS WP-82 manual

ELMETRON

ELMETRON CP-511 user manual

PCB Piezotronics

PCB Piezotronics 003C30 Installation and operating manual

Tenma

Tenma 72-10465 manual

Siemens

Siemens SITRANS F Coriolis FCT030 Function manual

KLINGER

KLINGER CMF V Series instruction manual

EXFO

EXFO FTB-2 Notice

Keysight

Keysight M8290A Getting started guide

ADTEK

ADTEK MW-5 operating manual

Acterna

Acterna MS1400 Operation manual

R&S

R&S ZPH manual